RESUMEN

A thin and conductive coating on an environmentally friendly polymer is imperative for protecting sensitive electronic devices. In this regard, a series of silver nanowires (AgNWs) coated nitrocellulose (NC) papers are fabricated by a simple and fast processed vacuum-assisted filtration method by varying filtrate volume to address electromagnetic interference. Their structural and EMI shielding performance is analyzed. The submicron thick and the lighter paper reveal the conductive AgNWs interwoven on the rough NC surface, making a 2D in-planar structure. Due to a strongly interconnected network, the coated paper displays an exceptional electrical conductivity of 8603 S/m. Despite having a minimum AgNW coating thickness of ∼0.69 µm and an area density of 0.041 mg/cm2, an ultrahigh EMI shielding effectiveness (SE) of about 69.4 dB (a specific EMI SE (SE/t) of 1005797 dB/cm) in the entire X-band (8-12 GHz) region is achieved. The effective material parameters, extracted using plane-wave theory, indicate that AgNWs form closed current loops resulting in magnetic losses. These AgNWs coated NC papers synthesized by a simple procedure are promising EMI shielding materials for current emerging electronic devices.

RESUMEN

We present an experimental system that combines differential electrochemical mass spectrometry with hydrodynamic flow consisting of an impinging jet in a wall-tube configuration. This assembly allows simultaneous detection of electrochemical signals along with monitoring of dissolved gas species using differential electrochemical mass spectrometry under well-defined hydrodynamic conditions and over a wide range of mass transfer rates. The working electrode is deposited directly onto a thin, hydrophobic membrane, which also serves as the inlet to the mass spectrometer. This inlet provides extremely rapid mass detection as well as a high flux of products from the electrode surface into the mass spectrometer. The impinging jet is designed in a wall-tube configuration, in which the jet diameter is large compared to the electrode diameter, thus providing uniform and rapid mass transfer conditions over the entirety of the electrode surface. This combination of rapid detection and controllable flow conditions allows a wide range of hydrodynamic conditions to be accessed with simultaneous electrochemical and mass spectrometric detection of dissolved gas species, which is important in the analysis of a range of electrochemical reactions. The capabilities of this configuration are illustrated using a platinum-coated electrode and several electrochemical reactions, including ferrocyanide oxidation, proton reduction, and oxalic acid oxidation.

RESUMEN

Microwave sintering of materials significantly depends on dielectric, magnetic and conductive Losses. Samples with high dielectric and magnetic loss such as ferrites could be sintered easily. But low dielectric loss material such as dielectric resonators (paraelectrics) finds difficulty in generation of heat during microwave interaction. Microwave sintering of materials of these two classes helps in understanding the variation in dielectric and magnetic characteristics with respect to the change in grain size. High-energy ball milled Ni0.6Cu0.2Zn0.2Fe1.98O4-delta and ZnTiO3 are sintered in conventional and microwave methods and characterized for respective dielectric and magnetic characteristics. The grain size variation with higher copper content is also observed with conventional and microwave sintering. The grain size in microwave sintered Ni0.6Cu0.2Zn0.2Fe1.98O4-delta is found to be much small and uniform in comparison with conventional sintered sample. However, the grain size of microwave sintered sample is almost equal to that of conventional sintered sample of Ni0.3Cu0.5Zn0.2Fe1.98O4-delta. In contrast to these high dielectric and magnetic loss ferrites, the paraelectric materials are observed to sinter in presence of microwaves. Although microwave sintered zinc titanate sample showed finer and uniform grains with respect to conventional samples, the dielectric characteristics of microwave sintered sample are found to be less than that of conventional sample. Low dielectric constant is attributed to the low density. Smaller grain size is found to be responsible for low quality factor and the presence of small percentage of TiO2 is observed to achieve the temperature stable resonant frequency.

Asunto(s)

RESUMEN

Development of materials and structures leading to lithium ion batteries with high energy and power density is a major requirement for catering to the power needs of present day electronic industry. Here, we report an in situ formation of a sandwiched structure involving single-walled carbon nanotube film, copper oxide, and copper during the direct synthesis of nanotube macrofilms over copper foils and their electrochemical performance in lithium ion batteries. The sandwiched structure showed a remarkably high reversible capacity of 220 mAh/g at a high cycling current of 18.6 A/g (50 C), leading to a significantly improved electrochemical performance which is extremely high compared to pure carbon nanotube and any other carbon based materials.