RESUMEN

Lignin is the natural binder in wood and lignocellulosic plants and is regarded as the main natural and renewable source of phenolic compounds. Its incorporation in the composition of fiberboards will enhance both the environmental performance of the panels and the complex use of natural resources. In recent years, the increased valorization of hydrolysis lignin in value-added applications, including adhesives for bonding fiberboard panels, has gained significant research interest. Markedly, a major drawback is the retention of lignin in the pulp until the hot-pressing process. This problem could be overcome by using a small content of phenol-formaldehyde (PF) resin in the adhesive mixture as an auxiliary binder. The aim of this research work was to investigate and evaluate the effect of the hot-pressing temperature, varied from 150 °C to 200 °C, in a modified hot-press cycle on the main physical and mechanical properties of fiberboard panels bonded with unmodified technical hydrolysis lignin (THL) as the main binder and PF resin as an auxiliary one. It was found that panels with very good mechanical properties can be fabricated even at a hot-pressing temperature of 160 °C, while to provide the panels with satisfactory waterproof properties, it is necessary to have a hot-pressing temperature of at least 190 °C.

RESUMEN

The present study aimed at utilizing technically hydrolyzed lignin (THL), industrial biomass residue, derived in high-temperature diluted sulfuric acid hydrolysis of softwood and hardwood chips to sugars. The THL was carbonized in a horizontal tube furnace at atmospheric pressure, in inert atmosphere and at three different temperatures (500, 600, and 700 °C). Biochar chemical composition was investigated along with its HHV, thermal stability (thermogravimetric analysis), and textural properties. Surface area and pore volume were measured with nitrogen physisorption analysis often named upon Brunauer-Emmett-Teller (BET). Increasing the carbonization temperature reduced volatile organic compounds (40 ÷ 96 wt. %), increased fixed carbon (2.11 to 3.68 times the wt. % of fixed carbon in THL), ash, and C-content. Moreover, H and O were reduced, while N- and S-content were below the detection limit. This suggested biochar application as solid biofuel. The biochar Fourier-transform infrared (FTIR) spectra revealed that the functional groups were gradually lost, thus forming materials having merely polycyclic aromatic structures and high condensation rate. The biochar obtained at 600 and 700 °C proved having properties typical for microporous adsorbents, suitable for selective adsorption purposes. Based on the latest observations, another biochar application was proposed-as a catalyst.

Asunto(s)

RESUMEN

This study aimed to propose an alternative technological solution for manufacturing fiberboard panels using a modified hot-pressing regime and hydrolysis lignin as the main binder. The main novelty of the research is the optimized adhesive system composed of unmodified hydrolysis lignin and reduced phenol-formaldehyde (PF) resin content. The fiberboard panels were fabricated in the laboratory with a very low PF resin content, varying from 1% to 3.6%, and hydrolysis lignin addition levels varying from 7% to 10.8% (based on the dry wood fibers). A specific two-stage hot-pressing regime, including initial low pressure of 1.2 MPa and subsequent high pressure of 4 MPa, was applied. The effect of binder content and PF resin content in the adhesive system on the main properties of fiberboards (water absorption, thickness swelling, bending strength, modulus of elasticity, and internal bond strength) was investigated, and appropriate optimization was performed to define the optimal content of PF resin and hydrolysis lignin for complying with European standards. It was concluded that the proposed technology is suitable for manufacturing fiberboard panels fulfilling the strictest EN standard. Markedly, it was shown that for the production of this type of panels, the minimum total content of binders should be 10.6%, and the PF resin content should be at least 14% of the adhesive system.

RESUMEN

This work presents a kinetic investigation of dilute sulfuric acid hydrolysis of bleached hardwood kraft pulp. The temperature-time dependence shows fast xylose extraction during the initial period of the process, while the glucose content increases slowly and permanently over the period. A conversion of xylose into furfural and furfural-derived chromophores is observed. It is established that only a low-brightness microcrystalline cellulose when a degree of polymerization below 300 can be obtained from hardwood pulp. The study of the acid hydrolysis kinetics, with respect to the degree of polymerization of microcrystalline cellulose, shows that the modified Prout-Tompkins equation describes most adequately the process. According to that kinetic model, the hydrolysis rate depends on a combination of chemical interaction and diffusion processes. It is evident that the activation energy does not change in the course of the process, i.e. the cellulose active centers do not change their activity.

Asunto(s)