RESUMEN
Starch-based materials seem to be an excellent alternative for conventional plastics used in various applications. Microfibralted cellulose can be used to improve the surface properties of starch-based materials. This study aims to analyze the surface properties of starch-microfibrillated cellulose materials. The surface properties of films were evaluated by ATR-FTIR, surface roughness, water wettability, and surface free energy. The surface homogeneity between corn starch and microfibrillated cellulose (MFC) fibers was confirmed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Microscopic analyses of the film surfaces confirm good compatibility of starch and MFC. The addition of MFC increased the surface roughness and polarity of developed starch/MFC materials. The surface roughness parameter has increased from 1.44 ± 0.59 to 2.32 ± 1.13 for pure starch-based materials and starch/MFC material with the highest MFC content. The WCA contact angle has decreased from 70.3 ± 2.4 to 39.1 ± 1.0°, while the surface free energy is 46.2 ± 3.4 to 66.2 ± 1.5 mJ·m-2, respectively. The findings of this study present that surface structure starch/MFC films exhibit homogeneity, which would be helpful in the application of MFC/starch materials for biodegradable packaging purposes.
RESUMEN
This study aimed to analyze the influence of the thermal treatment of shear thickening fluids, STFs, on their viscosity. For this purpose, shear thickening fluids based on polypropylene glycols PPG400 and PPG1000 and Aerosil®200 were developed. The shear thickening behavior of obtained fluids was confirmed by using a parallel-plate rheometer. Next, thermogravimetric (TG) analyses were used to characterized thermal stability and weight loss of the STFs at a constant temperature. Finally, the thermal treatment of the STFs obtained was provided using the apparatus developed for this purpose. The received STFs exhibited a very high maximum viscosity up to 15 kPa. The rheology of the STFs measured after thermal treatment indicated that the proposed method allowed the development of STFs with a very high maximum viscosity. The maximum viscosity of the STFs increased twofold when thermal treatment of the STFs at elevated temperature for 210 min was performed. TG confirmed the convergence of the weight loss in the apparatus. Our results show that controlling the thermal treatment of STFs allows STFs to be obtained with high viscosity and a dilatation jump of the STFs by degradation of the liquid matrix.
RESUMEN
Shear thickening fluids (STFs) are innovative materials that can find applications in smart body armor. However, the usage of STFs is limited by the aging of these materials. This work aims to analyze the influence of UV radiation on the aging process of STFs. The investigation was done experimentally, and artificial aging was applied to investigate the impact of UV radiation on the properties of STFs. The shear-thickening properties of obtained STFs were confirmed by viscosity measurements. The STFs based on PPG425, PPG2700, and KE-P10 exhibited a very high maximum viscosity of up to 580.7 Pa·s and 3313 Pa·s for the STF425 and STF2700, respectively. The aging of the obtained STFs caused the liquid matrix degradation, causing damage to the STFs and their change from liquid into solid. Furthermore, the FT-IR, 1H NMR, and 13C NMR spectroscopies were used for the confirmation of the breakdown of STFs. The FT-IR spectroscopy revealed the appearance of carbonyl groups in STFs after aging. Moreover, 1H NMR and 13C NMR spectroscopy confirmed the formation of the typical groups containing carbonyl groups. Our results demonstrate that STFs are UV light-sensitive and may lose their properties during storage.
RESUMEN
Poly(hydroxyurethane)s (PHU) are alternatives for conventional polyurethanes due to the use of bis-cyclic dicarbonates and diamines instead of harmful and toxic isocyanates. However, the surface properties of poly(hydroxyurethane)s are not well known. In this work, we focus on the analysis of the surface properties of poly(hydroxyurethane) coatings. Poly(hydroxyurethane)s were obtained by a catalyst-free method from commercially available carbonated diglycidyl ether of bisphenol A (Epidian 6 epoxy resins) and various diamines: ethylenediamine, trimethylenediamine, putrescine, hexamethylenediamine, 2,2,4(2,4,4)-trimethyl-1,6-hexanediamine, m-xylylenediamine, 1,8-diamino-3,6-dioxaoctane, 4,7,10-trioxa-1,13-tridecanediamine, and isophorone diamine, using a non-isocyanate route. The structures of the obtained polymers were confirmed by FT-IR, 1H NMR and 13C NMR spectroscopy, and thermogravimetric (TGA) and differential scanning calorimetry (DSC) analyses were performed. The rheological characteristic of the obtained polymers is presented. The static contact angles of water, diidomethane, and formamide, deposited on PHU coatings, were measured. From the measured contact angles, the surface free energy was calculated using two different approaches: Owens-Wendt and van Oss-Chaudhury-Good. Moreover, the wetting envelopes of PHU coatings were plotted, which enables the prediction of the wetting effect of various solvents. The results show that in the investigated coatings, a mainly dispersive interaction occurs.
RESUMEN
This article contains original experimental data, figures and methods to the preparation of non-isocyanate poly(hydroxyurethanes) by an environmentally friendly method without the use of toxic phosgene and isocyanates from bis(2,3-dihydroxypropyl)ether dicarbonate and various diamines (Tryznowski et al., Submitted for publication) [1]. Bis(2,3-dihydroxypropyl)ether dicarbonate was obtained from a one-step procedure from commercially available diglycerol. The product was characterized by (1)H NMR, (13)C NMR, and FTIR spectroscopies and for the first time by X-Ray diffraction measurements. Then, the bis(cyclic carbonate) monomer was used as a precursor for the synthesis of various NIPUs. The NIPUs were prepared in a non-solvent process. Spectral and thermal properties of the NIPUs are compered. Here we give the procedure in order to perform bis(2,3-dihydroxypropyl)ether dicarbonate with high yield and the procedure NIPU synthesis and the complete set of monomer and NIPU analysis ((1)H NMR, (13)C NMR, FTIR, X-Ray).