RESUMEN

OBJECTIVES: To biomechanically compare the stiffness of midshaft synthetic clavicle osteotomies fixed with either superior anatomic pre-contoured locking plates, anterior anatomic pre-contoured locking plates, or short-segment dual orthogonal mini-plate fixation. DESIGN AND SETTING: Controlled laboratory study. Specimens Twenty-one synthetic pre-osteotomized clavicles were separated into three groups: superior plating, anterior plating, or dual-plating. Each clavicle was sequentially tested in non-destructive cycles of axial compression, three-point bending, and torsion. Load and displacement were recorded. Stiffness was calculated. RESULTS: No statistically significant differences were found between construct stiffness during axial compression, three-point bending, or torsional testing. One superior plated clavicle suffered catastrophic failure during axial compression. One dual mini-fragment plated clavicle suffered catastrophic failure during torsion. CONCLUSIONS: Orthogonal dual mini-fragment fixation of transverse clavicle fractures is biomechanically similar to superior and anterior pre-contoured anatomic locking plate fixation. No statistically significant differences in construct stiffness were found in axial compression, three-point bending, or torsion testing. Further clinical research is required to determine the long-term stability of dual mini-fragment plate fixation. LEVEL OF EVIDENCE: IV.

Asunto(s)

RESUMEN

AIMS: In countries with social healthcare systems, such as Canada, patients may experience long wait times and a decline in their health status prior to their operation. The aim of this study is to explore the association between long preoperative wait times (WT) and acute hospital length of stay (LoS) for primary arthroplasty of the knee and hip. METHODS: The study population was obtained from the provincial Patient Access Registry Nova Scotia (PARNS) and the Canadian national hospital Discharge Access Database (DAD). We included primary total knee and hip arthroplasties (TKA, THA) between 2011 and 2017. Patients waiting longer than the recommended 180 days Canadian national standard were compared to patients waiting equal or less than the standard WT. The primary outcome measure was acute LoS postoperatively. Secondarily, patient demographics, comorbidities, and perioperative parameters were correlated with LoS with multivariate regression. RESULTS: A total of 11,833 TKAs and 6,627 THAs were included in the study. Mean WT for TKA was 348 days (1 to 3,605) with mean LoS of 3.6 days (1 to 98). Mean WT for THA was 267 days (1 to 2,015) with mean LoS of 4.0 days (1 to 143). There was a significant increase in mean LoS for TKA waiting longer than 180 days (2.5% (SE 1.1); p = 0.028). There was no significant association for THA. Age, sex, surgical year, admittance from home, rural residence, household income, hospital facility, the need for blood transfusion, and comorbidities were all found to influence LoS. CONCLUSION: Surgical WT longer than 180 days resulted in increased acute LoS for primary TKA. Meeting a shorter WT target may be cost-saving in a social healthcare system by having shorter LoS. Cite this article: Bone Jt Open 2021;2(8):679-684.

RESUMEN

Humeral avulsion of the glenohumeral ligament (HAGL) is a rare cause of anterior shoulder instability. Recurrent instability and anterior shoulder pain could be caused by an unrepaired HAGL; therefore, making the diagnosis is crucial. Only a few articles describe arthroscopic HAGL repair. This uncommon technique uses lateral decubitus arthroscopy and standard Bankart instrumentation. Different methods used to facilitate visualization of the working space as well as anchor placements are described.

RESUMEN

Spinoglenoid cysts are associated with labral tears; however, little is known about their associated bony pathology. This Technical Note describes an arthroscopic technique to decompress and subsequently graft a spinoglenoid cyst and associated bony defect. Appropriate preoperative imaging is key to understanding the location of the bony defect and therefore crucial to the success of the bone graft. Adequate release of the labrum should be performed to fully visualized the bony lesion. A subchondroplasty cannulated drill is then placed in the bony defect under direct visualization and said defect is then filled with calcium phosphate cement. Care is taken to ensure no cement is allowed to extrude into the shoulder joint. After the cement has cured, labral pathology is repaired and the usual postoperative physiotherapy protocol is initiated.

Asunto(s)