RESUMEN
Superconducting magnets used for Magnetic Resonance Imaging (MRI) scanners need to keep temperature gradients minimized in order to retain thermal and operating current margin. We have used 3D finite element analysis (FEA) simulation in COMSOL Multiphysics software that includes both conductive heat transfer and radiative heating to calculate the temperature distribution both along the winding direction and across the cross-section of an MRI segment coil at its equilibrium operating temperature. We have also modelled the evolution of the thermal properties during cool-down from ambient temperature. The heat capacity and thermal conductivity of the magnet winding were computed for use within this simulation. The heat capacity as a function of temperature was calculated using a rule of mixtures. This procedure was also used for the thermal conductivity along the direction of the wire. However, the thermal conductivity within the composite cross section (x- and y-directions) was computed using a 2D FEA model. Based on this, a time-dependent, 3D coil model was built to calculate the coil temperature throughout the winding during cool-down in our test cryostat system. The model included a heat leak component to the coil current contacts via conduction through the current leads as well as a radiative component from the surfaces of the cryostat. A key result was that a maximum coil ΔTmax = 5.1 K (=maximum temperature within the winding -minimum temperature in the winding) was seen and a coil Ic margin of 12.75 A was predicted at steady state, with our first current lead design. A second set of more optimized current leads significantly lowered the ΔTmax within the coil at the steady state. The coil Ic margin has been analyzed for different current lead designs.
RESUMEN
The paper begins by emphasizing the clinical and commercial importance of proton or other charged particle such as carbon ion therapy, refers to the manufacturers of such systems of which more than 120 are installed or under construction worldwide by April 2021. A general review of charged particle therapy systems refers to six manufacturers and provides in tabular form some details of systems installed in the US, Europe, Asia, and elsewhere. In a description of the principles of particle beam therapy a comparison is made of the properties of photons (x-rays) versus protons and protons versus carbon ions. A brief discussion of accelerators in general is followed by descriptions of cyclotrons (including the isosynchronous cyclotron and the synchrocyclotron) and synchrotrons. An interesting case study describes the evolution of a normal-conducting 220 ton cyclotron into an iron-free synchrocyclotron weighing only 5 tons. The general principles of beam handling and gantry design are described. Subsequent sections describe gantry magnets in detail - normal conducting gantry magnets, superconducting gantry magnets for proton- and carbon therapy. Mention is made of a novel CERN-designed superconducting toroidal gantry for hadron therapy, GaToroid. This device, operating under steady state current and magnetic field, is able to deliver a beam at discrete angles over a range of treatment energies. Also considered are low temperature superconducting (LTS) and high temperature superconducting (HTS) magnet windings, and the choice of REBCO conductors for cryogen-free carbon-ion gantries. Finally, the paper mentions an important "Prospect for Improvement", viz: the introduction of MRI image guidance. A well-known property of the particle beam as it passes through tissue is its energy dependent absorption that rises to a pronounced peak (the Bragg peak) at the end of its range. In order to take advantage of this effect the exact targeting of the tumor and positioning of the patient should be guided by imaging visualization using X-ray, CT, and hopefully advanced MRI. Unlike MRI-guided photon therapy the direct interaction of the magnetic field with the charged particle beam presents a huge challenge such that MRI image-guided proton/particle therapy has not yet been available in clinical practice. Modeling studies have been undertaken on the general topic of beam-line/magnetic field interaction using, for example, the software GEANT4 (GEometry And Tracking) a platform for simulating the passage of charged particles through matter using a Monte Carlo method.
RESUMEN
A series of SnO2 added MgB2 bulk superconductors were prepared by in situ route to study the effect of oxygen doping on superconducting and structural properties of MgB2. Several (MgB2)1-x (SnO2) x samples were fabricated with x ranging from 0, 3 wt%, 4 wt%, and 6 wt%. Upper critical field (B C2) and irreversible field (B irr) were measured by physical property measurement system. Thermal analysis was performed on the as-received SnO2 powder. Critical current densities (J cm ) were obtained at 4.2 K using magnetic measurement. X-ray diffraction results showed evidence of full SnO2 decomposition in all the doped bulk samples and a shift of a-axis in MgB2 lattice was seen. Oxygen was successfully released during heat treatment, yet no enhancement of B C2 or B irr was seen, indicating that oxygen atoms did not end up in the host lattice. Further exploration of different processing procedures is still needed in order to get oxygen substitution on the host lattice sites.