RESUMEN
Porous, tubular, flexible, and elastic poly(trimethylene carbonate) (PTMC) scaffolds (length 8 cm and inner diameter 3 mm) for vascular tissue engineering were prepared by means of a dip-coating and particulate leaching procedure. Using NaCl as porogen, scaffolds with an average pore size of 110 µm and a porosity of 85% were obtained. Before leaching the salt, the structures were made creep-resistant by means of crosslinking at 25 kGy gamma irradiation. To increase the efficiency of cell seeding, the scaffolds were provided with a microporous outer layer of 0.2 mm with an average pore size of 28 µm and a porosity of 65% (total wall thickness 1 mm). Human smooth muscle cells (SMCs) were seeded in these scaffolds with an efficiency of 43%, as determined after 24 h cell adhesion. SMCs were cultured in the scaffolds up to 14 days under stationary conditions or under pulsatile flow conditions in a bioreactor (pressure 70-130 mmHg, 69 pulsations/min, and average wall shear rate 320 s(-1)). Although SMCs proliferated under both conditions, cell numbers were three to five times higher in case of dynamic culturing. This was qualitatively confirmed by means of histology. Also, in terms of mechanical properties, the dynamically cultured constructs performed better than the statically cultured constructs. After culturing for 14 days, the maximum tensile strengths of the constructs, determined in the radial direction, had increased from 0.16 MPa (unseeded scaffold) to 0.48 MPa (dynamic culturing) and 0.38 MPa (static culturing). The results of this study indicate that a potentially useful medial layer for tissue-engineered vascular grafts can be prepared by dynamic culturing of human SMCs seeded in porous tubular poly(trimethylene carbonate) scaffolds.
Asunto(s)
Vasos Sanguíneos/crecimiento & desarrollo , Miocitos del Músculo Liso/citología , Miocitos del Músculo Liso/fisiología , Poliésteres/síntesis química , Ingeniería de Tejidos/instrumentación , Andamios del Tejido , Materiales Biocompatibles/síntesis química , Técnicas de Cultivo de Célula/instrumentación , Proliferación Celular , Análisis de Falla de Equipo , Humanos , Diseño de PrótesisRESUMEN
CD151 is a cell surface protein that belongs to the tetraspanin superfamily. It forms complexes with the laminin-binding integrins alpha3beta1, alpha6beta1 and alpha6beta4 and is codistributed with these integrins in many tissues at sites of cell-matrix interactions. In this study we show that CD151 can also form stable complexes with the laminin-binding integrin alpha7beta1. The strength of this interaction is comparable to that between CD151 and alpha3beta1. Complexes of alpha3beta1, alpha6beta1 and alpha7beta1 with CD151 are equally well formed with all splice variants of the alpha3, alpha6 and alpha7 subunits, and complex formation is not affected by mutations that prevent the cleavage of the integrin alpha6 subunit. Like the expression of alpha3beta1 and alpha6beta1, expression of alpha7beta1 in K562 cells results in increased levels of CD151 at its surface. Two non-integrin laminin receptors, dystroglycan and the polypeptide on which the Lutheran blood group antigens are expressed, are also often colocalized with CD151, but no association with CD151-alpha3beta1 complexes was found with biochemical analysis. The anti-CD151 antibody TS151R detects an epitope at a site at which CD151 interacts with integrins, and therefore it cannot react with CD151 when it is bound to an integrin. Comparison of the straining patterns produced by TS151R with that by of an anti-CD151 antibody recognizing an epitope outside the binding site (P48) revealed that most tissues expressing one or more laminin-binding integrins reacted with P48 but not with TS151R. However, smooth muscle cells that express alpha7beta1 and renal tubular epithelial cells that express alpha6beta1 were stained equally well by TS151R and P48. These results suggest that the interactions between CD151 and laminin-binding integrins are subject to cell-type-specific regulation.