RESUMEN

Surface acoustic wave (SAW) radio-frequency identification (RFID) tags are soon expected to be produced in very high volumes. The size and cost of a SAW RFID tag will be key parameters for many applications. Therefore, it is of primary importance to reduce the chip size. In this work, we describe the design principles of a 2.4-GHz SAW RFID tag that is significantly smaller than earlier reported tags. We also present simulated and experimental results. The coded signal should arrive at the reader with a certain delay (typically about 1 micros), i.e., after the reception of environmental echoes. If the tag uses a bidirectional interdigital transducer (IDT), space for the initial delay is needed on both sides of the IDT. In this work, we replace the bidirectional IDT by a unidirectional one. This halves the space required by the initial delay because all the code reflectors must now be placed on the same side of the IDT. We reduce tag size even further by using a Z-path geometry in which the same space in x-direction is used for both the initial delay and the code reflectors. Chip length is thus determined only by the space required by the code reflectors.

Asunto(s)

RESUMEN

Recent developments in wide bandwidth SAW filter design led to the use of complex electroacoustic cells, such as the Hanma-Hunsinger cell. For this kind of structure, it is not sufficient to use only a single electrode periodic FEM/BEM model to derive the P-matrix parameters. The present paper proposes a mixed FEM/BEM numerical model for the simulation of a periodic array of metallic electrodes, the elementary cell of which can be as complex as necessary: it can contain several electrodes, connected to active ports, or short-circuited, or floating.

RESUMEN

Surface acoustic wave (SAW) resonators on lithium tantalate (LiTaO3) and lithium niobate (LiNbO3) are investigated. The amplitude of the acoustic fields in the resonators are measured using a scanning laser interferometer. The amplitude profiles of the surface vibrations reveal the presence of distinct acoustic beams radiated from the transducer region of the SAW resonators and propagating with low attenuation. We suggest that this radiation is generated by the charges accumulating at the tips of the finger electrodes. The periodic system of sources, namely oscillating charges at the fingertips, generates Rayleigh-wave beams in the perpendicular and oblique directions. Green's function theory is used to calculate the coupling strength and slowness of the Rayleigh waves on 42 degrees Y-cut LiTaO3 and Y-cut LiNbO3 substrates as a function of the propagation direction. Furthermore, the propagation angles of the Rayleigh-wave beams as a function of frequency are calculated. The computed angles are compared with the measured ones for both the LiTaO3 and LiNbO3 substrates.

Asunto(s)

RESUMEN

The need for high-frequency, wide-band filters has instigated many developments based on combining thin piezoelectric films and high acoustic velocity materials (sapphire, diamond-like carbon, silicon, etc.) to ease the manufacture of devices operating above 2 GHz. In the present work, a technological process has been developed to achieve thin-oriented, single-crystal lithium niobate (LiNbO3) layers deposited on (100) silicon wafers for the fabrication of radio-frequency (RF) surface acoustic wave (SAW) devices. The use of such oriented thin films is expected to favor large coupling coefficients together with a good control of the layer properties, enabling one to chose the best combination of layer orientation to optimize the device. A theoretical analysis of the elastic wave assumed to propagate on such a combination of material is first exposed. Technological aspects then are described briefly. Experimental results are presented and compared to the state of art.

Asunto(s)

RESUMEN

The high-phase velocity (above 6100 m/s in an aluminum (Al) grating on lithium niobate (LiNbOs)) of the longitudinal leaky surface acoustic wave (SAW) (LLSAW) mode makes it attractive for application in high-frequency SAW ladder filters in the 2-5 GHz range. We investigate the dependence of one-port synchronous LLSAW resonator performance on YZ-LiNbO3 on the metallization thickness and metallization ratio, both experimentally and theoretically. Our results indicate a strong dependence of the Q factor and resonance frequency on the aluminum thickness, with the optimal thickness that produces the highest Q values being about 8%. The optimal thickness increases with the metallization ratio. The observed behavior is interpreted with the help of simulations using a combined finite element method (FEM)/boundary element method (BEM) technique. As an application, bandpass filters have been fabricated in the 2.8 GHz frequency regime, based on LLSAWs. The synchronous resonators constituting the ladder filters operate in the fundamental mode. The filters feature low insertion losses below 3 dB and wide relative passbands of 4.5-5%.

RESUMEN

Analysis of the quartz properties shows the existence of unexplored angular domains for which Rayleigh waves can be efficiently excited, exhibiting physical characteristics better than the ones of the (ST,X) cut. This paper presents a family of quartz cuts allowing significant improvements of surface acoustic wave (SAW) devices on quartz. A first set of experiments has been performed, confirming the theoretical predictions of the basic properties of SAW on these cuts. A second set of measurements then was achieved to refine the identification of coefficients needed to perform industrial SAW design. A demonstration of the improvements accessible using this new cut is presented. A low loss SAW filter working at 71 MHz has been fabricated using smaller aluminum thickness than that for standard quartz cuts, and exhibiting all the properties required for its industrial implementation.