RESUMEN

BACKGROUND: 2-Heptanone is a volatile liquid known to be effective in protecting honey bees from parasitic mite infestations in hives. The present study aimed to show that chemical derivatives of 2-heptanone would release the ketone for a significantly longer time than it takes for the pure ketone to evaporate and preferably for as long as two brood cycles of a honey bee (42 days). RESULTS: A liquid ketal of 2-heptanone with glycerol (Glyc-Ket) and solid ketals of the ketone with polyvinyl alcohol (PVAl-Ket), containing different amounts of the ketone, were synthesized. The fully resolved 1 H and 13 C nuclear magenetic resonance (NMR) spectra of the ketals are discussed. In the case of the polymer, differential scanning calorimetry (DSC) of a ketal was also compared with the unketalized polyvinyl alcohol. The length of time for which 2-heptanone was released by the ketals was determined by gas chromatography-mass spectrometry of the headspace. In the case of Glyc-Ket, the concentration of the 2-heptanone in the liquid phase was also monitored by 1 H NMR spectroscopy. The deketalization was pH dependent, ranging between 2.0 and 2.5 for Glyc-Ket and between 2.0 and 3.5 for PVAl-Ket. CONCLUSION: Under bee hive conditions, the release of 55 mmol 2-heptanone from Glyc-Ket lasted for 42 days, whereas the release of the ketone from the PVAl-Ket with a similar amount of the ketone lasted for 23 days, versus a maximum of 17 days for an equivalent amount of the pure ketone. These ketals therefore have the potential to be effective mite repellants for the protection of honey bees. © 2019 Society of Chemical Industry.

Asunto(s)

RESUMEN

A heat expansion process similar to that used for expanded bead polystyrene was used to expand starch-based compositions. Foam beads made by solvent extraction had the appearance of polystyrene beads but did not expand when heated due to an open-cell structure. Nonporous beads, pellets, or particles were made by extrusion or by drying and milling cooked starch slurries. The samples expanded into a low-density foam by heating 190-210 degrees C for more than 20 s at ambient pressures. Formulations containing starch (50-85%), sorbitol (5-15%), glycerol (4-12%), ethylene vinyl alcohol (EVAL, 5-15%), and water (10-20%) were studied. The bulk density was negatively correlated to sorbitol, glycerol, and water content. Increasing the EVAL content increased the bulk density, especially at concentrations higher than 15%. Poly(vinyl alcohol) (PVAL) increased the bulk density more than EVAL. The bulk density was lowest in samples made of wheat and potato starch as compared to corn starch. The expansion temperature for the starch pellets decreased more than 20 degrees C as the moisture content was increased from 10 to 25%. The addition of EVAL in the formulations decreased the equilibrium moisture content of the foam and reduced the water absorption during a 1 h soaking period.

Asunto(s)

RESUMEN

Volatile agrochemicals such as 2-heptanone have potential in safely and effectively controlling important agricultural pests provided that they are properly delivered. The present study reports the permeability of starch gel matrices and various coatings, some of which are agricultural-based, that could be used in controlled release devices. Low-density, microcellular starch foam was made from wheat, Dent corn, and high amylose corn starches. The foam density ranged from 0.14 to 0.34 g/cm3, the pore volume ranged from 74 to 89%, and the loading capacity ranged from 2.3 to 7.2 times the foam weight. The compressive properties of the foam were not markedly affected by saturating the pore volume with silicone oil. The vapor transmission rate (VTR) and vapor permeability (VP) were measured in dry, porous starch foam and silicone-saturated starch gels. VTR values were highest in foam samples containing solvents with high vapor pressures. Silicone oil-saturated gels had lower VTR and VP values as compared to the dry foam. However, the silicone oil gel did not markedly reduce the VP for 2-heptanone and an additional vapor barrier or coating was needed to adequately reduce the evaporation rate. The VP of films of beeswax, paraffin, ethylene vinyl alcohol, a fruit film, and a laminate comprised of beeswax and fruit film was measured. The fruit film had a relatively high VP for polar solvents and a very low VP for nonpolar solvents. The laminate film provided a low VP for polar and nonpolar solvents. Perforating the fruit film portion of the laminate provided a method of attaining the target flux rate of 2-heptanone. The results demonstrate that the vapor flux rate of biologically active solvents can be controlled using agricultural materials.

Asunto(s)

RESUMEN

Vitamin B12-catalyzed reductive dechlorination of perchloroethylene (PCE) and trichloroethylene (TCE) is a potential strategy for cleanup of polluted environments. Presented are crystal structures of vinylcobalamin 2 and cis-chlorovinylcobalamin 1. They show a strong resistance toward photolysis. Reduction of 2 is difficult, but reduction of 1 occurs readily and produces 2. The mechanism of this latter reaction involves acetylene as an intermediate. These and other findings are discussed in the context of environmental studies on B12-catalyzed dechlorination of PCE and TCE and investigations of the haloalkene reductive dehalogenases that catalyze similar reactions.

Asunto(s)

RESUMEN

In the presence of catalytic vitamin B(12) and a reducing agent such as Ti(III)citrate or Zn, arylalkenes are dimerized with unusual regioselectivity forming a carbon [bond] carbon bond between the benzylic carbons of each coupling partner. Dimerization products were obtained in good to excellent yields for mono- and 1,1-disubstituted alkenes. Dienes containing one aryl alkene underwent intramolecular cyclization in good yields. However, 1,2-disubstituted and trisubstituted alkenes were unreactive. Mechanistic investigations using radical traps suggest the involvement of benzylic radicals, and the lack of diastereoselectivity in the product distribution is consistent with dimerization of two such reactive intermediates. A strong reducing agent is required for the reaction and fulfills two roles. It returns the Co(II) form of the catalyst generated after the reaction to the active Co(I) state, and by removing Co(II) it also prevents the nonproductive recombination of alkyl radicals with cob(II)alamin. The mechanism of the formation of benzylic radicals from arylalkenes and cob(I)alamin poses an interesting problem. The results with a one-electron transfer probe indicate that radical generation is not likely to involve an electron transfer. Several alternative mechanisms are discussed.