RESUMEN

The recovery of ammonium from urine requires distinguishing and excluding sodium and potassium. A polymer inclusion membrane selective for ammonium is developed using an ionophore based on pyrazole substituted benzene. The interactions of the components are studied, as well as their effect on transport and selectivity. Spectroscopic and thermogravimetric measurements show no extensive physical interactions of the components, and that the plasticizer reduces the intermolecular forces (rigidity) of the membrane. The ionophore turns the membrane more rigid, although it increases its swelling degree and therefore the affinity of cations. A ratio of plasticizer (DEHP) and polymer (PVC) of 1:3 in mass gives the highest ammonium flux. Tested contents of ionophore (2 and 5 wt%) show that the higher the content of the ionophore, the fastest the flux is (7.5 × 10(-3) mmol cm(-2) h(-1) ). Selectivity of NH4 (+) over Na(+) and over K(+) is reduced from 13.07 to 9.33 and from 14.15 to 9.57 correspondingly.

Asunto(s)

RESUMEN

Potassium is an important nutrient used in fertilizers but is not always naturally available We investigated the properties of polymer inclusion membranes (PIM) regarding their selective recovery of K⁺ over competitive ions typically present in urine (Na⁺ and NH4⁺). The greatest flux was observed when the ratio of mass 2-nitrophenyl octyl ether (2-NPOE) used as plasticizer to cellulose triacetate (CTA) used as polymer was 0.25. The highest flux was achieved with a content of 24.8 wt % of dicyclohexan-18-crown-6 (DCH18C6) used as carrier, although the highest selectivity was observed with a content of 14.0 wt % of DCH18C6. We also studied whether the transport mechanism occurring in our system was based on co-transport of a counter-ion or ion exchange. Two different receiving phases (ultrapure water and 100 mM HCl) were tested. Results on transport mechanisms suggest that co-transport of cations and anions is taking place across our PIMs. The membrane deteriorated and lost its properties when the receiving phase was acidic; we suggested that this was due to hydrolysis of CTA. The greatest flux and selectivity were observed in ultrapure water as receiving phase.

RESUMEN

In this paper we studied the performance of bioanodes under different experimental conditions using polarization curves and impedance spectroscopy. We have identified that the large capacitances of up to 1 mF·cm(-2) for graphite anodes have their origin in the nature of the carbonaceous electrode, rather than the microbial culture. In some cases, the separate contributions of charge transfer and diffusion resistance were clearly visible, while in other cases their contribution was masked by the high capacitance of 1 mF·cm(-2). The impedance data were analyzed using the basic Randles model to analyze ohmic, charge transfer and diffusion resistances. Increasing buffer concentration from 0 to 50mM and increasing pH from 6 to 8 resulted in decreased charge transfer and diffusion resistances; lowest values being 144 Ω·cm(2) and 34 Ω·cm(2), respectively. At acetate concentrations below 1 mM, current generation was limited by acetate. We show a linear relationship between inverse charge transfer resistance at potentials close to open circuit and saturation (maximum) current, associated to the Butler-Volmer relationship that needs further exploration.

Asunto(s)

RESUMEN

Energy extraction based on capacitive Donnan potential (CDP) is a recently suggested technique for sustainable power generation. CDP combines the use of ion-exchange membranes and porous carbon electrodes to convert the Gibbs free energy of mixing sea and river water into electric work. The electrodes geometry has a relevant impact on internal resistance and overall performance in CDP. In this work, we present the first effort to use wire-shaped electrodes and its suitability for improving CDP. Analytical evaluation and electrical measurements confirm a strong nonlinear decrease in internal resistance for distances between electrodes smaller than 3 mm. We also demonstrated that we get more power per material invested when compared to traditional flat plate designs. These findings show the advantages of this design for further development of CDP into a mature technology.

Asunto(s)