RESUMEN
PURPOSE: To investigate the bending moment of implants restored with a directly screwed single-unit fixed dental prosthesis (FDP) compared to implants restored with an FDP polymerized to a titanium base before and after thermomechanical aging. MATERIALS AND METHODS: A total of 240 implants (120 with and 120 without a titanium base) were restored with FDPs manufactured from conventionally sintered 3Y-TZP, 5Y-TZP, 4Y-TZP, and CoCrMo, as well as high-speed sintered 4Y-TZP. Half the specimens per subgroup were aged using chewing simulation combined with thermocycling (1,200,000 cycles at 50 N; 6,000 cycles at 5° to 55°). Initial and aged fracture load were measured. The bending moment was calculated and subjected to statistical analysis (Kolmogorov-Smirnov test, one-way ANOVA followed by post hoc Scheffé, t, and chi-square tests; P < .05). Failure types were analyzed. RESULTS: Implants without a titanium base showed higher bending moments for all initially tested zirconia groups compared to implants with a titanium base. The highest initial values were observed for 4Y-TZP FDPs regardless of implant type. High-speed sintered FDPs demonstrated higher initial bending moments compared to conventionally sintered FDPs. Artificial aging led to a decrease of the bending moment in most subgroups. After aging, no differences were found within the restoration materials, sintering protocols, or implant types. Implant deformation occurred mainly with directly screwed FDPs, whereas FDP mobility was predominantly observed among implants with a titanium base. FDP fractures were mainly observed for 5Y-TZP. CONCLUSIONS: Both implant types exhibited similar values after aging. Thus, implants without a titanium base seem to show equally sufficient stability for clinical applications with all tested materials.
Asunto(s)
Fracaso de la Restauración Dental , Titanio , Ensayo de Materiales , Análisis del Estrés Dental , Materiales Dentales , CirconioRESUMEN
PURPOSE: To investigate the bending moment of implants restored with a directly screwed single-unit fixed dental prosthesis (FDP) compared to implants restored with an FDP polymerized to a titanium base before and after thermomechanical aging. MATERIALS AND METHODS: A total of 240 implants (120 with and 120 without a titanium base) were restored with FDPs manufactured from conventionally sintered 3Y-TZP, 5Y-TZP, 4Y-TZP, and CoCrMo, as well as high-speed sintered 4Y-TZP. Half of the specimens per subgroup were aged using chewing simulation combined with thermocycling (1,200,000 cycles at 50 N; 6,000 cycles at 5°C to 55°C). Initial and aged fracture load were measured. The bending moment was calculated and subjected to statistical analysis (Kolmogorov-Smirnov test, one-way ANOVA followed by post hoc Scheffé, t, and chi-square tests; P < .05). Failure types were analyzed. RESULTS: Implants without a titanium base showed higher bending moments for all initially tested zirconia groups compared to implants with a titanium base. The highest initial values were observed for 4Y-TZP FDPs regardless of implant type. High-speed sintered FDPs demonstrated higher initial bending moments compared to conventionally sintered FDPs. Artificial aging led to a decrease of the bending moment in most of the subgroups. After aging, no differences were found within the restoration materials, sintering protocols, or implant types. Implant deformation occurred mainly with directly screwed FDPs, whereas FDP mobility was predominantly observed among implants with a titanium base. FDP fractures were mainly observed for 5Y-TZP. CONCLUSION: Both implant types exhibited similar values after aging. Thus, implants without a titanium base seem to show equally sufficient stability for clinical applications with all tested materials.
RESUMEN
OBJECTIVES: To test and compare two types of implant systems restored with four monolithic polymer-based materials with regard to their bending moments (BM) before and after aging. METHODS: A total of 192 tissue-level implants (TRI Dental Implants) differing in the presence (TiB, Octa line, n = 96) or absence (NTiB, Matrix line, n = 96) of a titanium base were restored with mandibular right first molar crowns manufactured from composite (CC), polymer-infiltrated ceramic (VE), PMMA (PM) and a 3D printed resin (ND) (n = 24). Half of the specimens (n = 12) were loaded for 1,200,000 cycles (50 N, 1.3 Hz, TC: 5/55 °C, 6000×) and examined for failures. Fracture load was measured according to ISO standard 14801, BM was calculated, and fracture types were examined. Data were analyzed using parametric statistics (p < 0.05). RESULTS: No failures were observed after 600,000 cycles. After 1,200,000 cycles, wear traces were recorded in all groups except PM, VE and CC on TiB implants. In group CC on NTiB implants, three specimens were rated zero in BM testing as they showed fracture of the screw. Regarding BM, TiB implants exhibited higher values than NTiB implants with aged CC (p = 0.023), aged PM (p < 0.001), initial PM (p = 0.011) and initial VE (p < 0.001). No differences occurred among the implant types with initial CC, initial ND, aged ND and aged VE. With regard to initial BM values, NTiB implants showed higher values for ND and CC compared with PM and VE (p < 0.001). No differences in initial BM values were found for the tested materials on TiB implants (p > 0.116). When aged, restoration material had no impact on the BM values of NTiB implants (p ≥ 0.233). Aged TiB implants showed higher values in combination with CC than with ND (p = 0.001). PM and VE showed similar values as ND and CC. Artificial aging led to a decrease of BM within PM, CC and ND on NTiB implants and ND on TiB implants. The majority of failures after testing were characterized by crown fractures in two to four pieces. Fractures in more pieces with smaller fragments occurred primarily for ND. SIGNIFICANCE: The use of NTiB implants with the polymer-based materials tested can only be recommended for clinical use as interim prostheses. CC seems to show a positive effect on the BM. Clinical research investigating the in vivo behavior is necessary to confirm these findings.