RESUMEN

AIM: The selectivity of a water jet (WJ) is already used with clinical advantage in the surgery of liver, brain, kidney and herniated lumbar discs. The aim of the present study was to determine whether a WJ can be used for synovectomy without damaging the joint capsule and the cartilage. METHOD: 60 human cadaver knee specimens (67 +/- 14 years) were dissected into synovial and cartilage samples. They were randomly assessed to four pressure groups (pW = 3; 6; 9; 12 MPa) and three jet surface angles (beta = 30; 60; 90 degrees) The nozzle diameter was dD = 0.12 mm, the stand off distance of the jet was s = 10 mm with a feed rate of vV = 2 mm/s. The acquired parameters were depth of the cuts, histological layer, and change of the samples thickness. RESULT: There was a correlation of the cutting depth and the pressure (pW), whereas the jet-surface angle (beta) showed no correlation. The synovial layer of the cut likewise correlated with the pressure. At pW = 6 MPa the stratum subsynoviale could be cut selectively without damaging the fibrous capsule or the cartilage. The increase of the samples thickness was caused by an interstitial oedema. CONCLUSION: The different mechanical properties of the joint capsule and the stratum subsynoviale lead to the selective cutting of the water jet. Since the joint capsule was not damaged, the feasibility of WJ synovectomy has been proven. The device can be used for synovectomy in parts of the joint that are not visible as well as in very small joints.

Asunto(s)

RESUMEN

We have investigated the effect of the long-range Coulomb interaction on the one-particle excitation spectrum of n-type germanium, using tunneling spectroscopy on mechanically controllable break junctions. At low temperatures, the tunnel conductance shows a minimum at zero bias voltage due to the Coulomb gap. Above 1 K, the gap is filled by thermal excitations. This behavior is reflected in the variable-range hopping resistivity measured on the same samples: up to a few degrees Kelvin the Efros-Shklovskii lnR infinity T(-1/2) law is obeyed, whereas at higher temperatures deviations from this law occur. The type of crossover differs from that considered previously in the literature.

RESUMEN

Water-jet cutting techniques have been used in industrial applications for many different materials. Recently these techniques have been developed into a revolutionary cutting tool for soft tissues in visceral surgery. The present study investigates the usage of this cutting technology for the revision surgery of endoprostheses. In the first part of the study, samples of bovine bone and acrylic bone cement (PMMA) were cut using an industrial jet cutting device with pure water. Below 400 bar, only PMMA was cut; above 400 bar, bone was also cut, but only pressures above 800 bar resulted in clinically useful rates of material removal (cut depth 2. 4 mm at 10 mm/min traverse speed). In the second part of the study, the effect of adding biocompatible abrasives to the water in order to reduce the required pressure was investigated, resulting in a significantly higher removal of material. At 600 bar, PMMA was cut 5. 2 mm deep with plain water and 15.2 mm deep with added abrasives. The quality of the cuts was increased by the abrasive. Though there was no clear selectivity between bone and PMMA any more, the rate of material removal at similar pressures was significantly higher for PMMA than for bone (600 bar: 1.6 mm cut depth for bone samples, 15.2 mm for PMMA). The measured cut depths with either method were not influenced by a change of the cutting direction with respect to the main direction of the osteons in the bone. However, a reduction of the jet surface angle (90 degrees to 23 degrees ) resulted for bone in a significantly lower cut depth at 600 bar (plain water: 0.62 mm vs. 0.06 mm; abrasive: 1.61 mm vs. 0.60 mm). The laboratory experiments indicate that abrasive water jets may be suitable for cutting biomaterials like bone and bone cement.

Asunto(s)

RESUMEN

Water jet techniques have been used in industrial cutting, drilling and cleaning applications for more than 30 years. Plain water is typically used for the cutting of non-metallic materials. The addition of abrasive substances to the stream allows almost any material to be cut. The first medical applications were reported in the early 1980s, when the water jet was used to cut organs. The present study investigates the use of water jet cutting technology for endoprosthesis revision surgery. Bone and PMMA (polymethylmethacrylate) samples were cut at different pressures using an industrial water jet cutting device. Using plain water at 400 bar, PMMA was cut selectively without damaging the bone; above 400 bar, bone was also cut, but the cutting depths in PMMA were significantly greater (p < 0.05). Adding a water-soluble abrasive disaccharide to the water results in a significantly higher removal rate for both materials (p < 0.05), but selectivity is lost, although the differences in cutting depth between the two materials was significant (p < 0.05). With an abrasive, the quality of the cut was better for both materials. The water jet technology--in particular the abrasive technique--can be used to cut biomaterials such as bone and bone cement. The diameter of the jet is a great advantage when working in the confined area at the prosthesis interface. The cutting process is essentially cold, thus eliminating a thermal effect, and the jet reaction forces are relatively low. Accurate manipulation of the hydro jet nozzle is possible both manually and by robot. The results obtained show that it is possible to remove prostheses with this cutting technique, rapidly and with little damage to the surrounding tissue. Problem areas are the development of sterile pumps and the "depth control" of the jet.

Asunto(s)