RESUMEN
The elevated co-occurrence of arsenic and fluoride in surface and groundwater poses risks to human health in many parts of the world. Using single and competitive batch equilibrium adsorption studies, this research focuses on As(V) and F adsorption by activated carbon and its modeling. BET, XRD, FESEM, EDS, and FTIR analysis were used to discern the structural characteristics of activated carbon. The influence of dosage, pH, and contact time were also investigated in single and simultaneous adsorption systems. The maximum adsorption capacity of activated carbon for arsenic and fluoride were found to be 3.58 mg/g and 2.32 mg/g, respectively. Kinetics studies indicated that pseudo-second-order kinetic model fit better than pseudo-first-order, Elovich, and intraparticle diffusion kinetic models. The non-linear regression analysis of Langmuir, Freundlich, Toth, Redlich Petersons, and Modified Langmuir Freundlich models was used to determine single-component asorption model parameters. Additionally, the simultaneous adsorption was rigorously modeled and compared using the Extended Langmuir (EL), Extended Langmuir Freundlich (ELF), Modified Competitive Langmuir (MCL), and Jeppu Amrutha Manipal Multicomponent (JAMM) isotherm models, and competitive mechanisms were interpreted for the simultaneous adsorption system. Further, the model performances were evaluated by statistical error analysis using the normalized average percentage error (NAPE), root mean square errors (RMSE), and the correlation coefficient (R2). According to the modeling results, single equilibrium data fitted better with the Modified Langmuir Freundlich isotherm model, with a higher R2 of 0.99 and lower NAPE values of 3.8 % and 1.28 % for As(V) and F, than other models. For the binary adsorption, the Extended Langmuir Freundlich isotherm model demonstrated excellent fit with lowest errors. All the competitive isotherm models fit the As(V) and F simultaneous sorption systems reasonably well. Furthermore, the research unveiled a nuanced hierarchy of isotherm fitting, with ELF > EL > MCL > JAMM in varying arsenic at a constant fluoride concentration, and ELF > JAMM > EL > MCL in varying fluoride at a constant arsenic concentrations. In addition, competitive studies divulged crucial insights into selective adsorption, as As(V) exhibits a pronounced adsorption selectivity over F on activated carbon. In essence, As(V) showed a more pronounced antagonistic behavior over F, whereas F exhibited a much lesser competitive behavior in the adsorption of arsenic.
RESUMEN
Researchers have made significant efforts over the past few decades to understand adsorption by developing various simple adsorption isotherm models. However, though many contaminants usually occur as multicomponent mixtures in nature, multicomponent adsorption isotherms have received limited attention and remain an area of inadequate research. We have presented here in a new multicomponent adsorption isotherm model, named the Jeppu Amrutha Manipal Multicomponent (JAMM) isotherm, that can alleviate this problem. We first developed the JAMM multicomponent isotherm using our experimental data sets of arsenic and fluoride competitive adsorption on activated carbon. We then tested the JAMM multicomponent isotherm for a case study of cadmium and zinc competitive adsorption. Next, we further assessed the JAMM isotherm using another competitive adsorption case study of copper and chromium. Through extensive validation studies and error analysis, the JAMM isotherm was able to demonstrate its efficacy in predicting the adsorption behavior in several multicomponent adsorption systems accurately. The main advantage of JAMM isotherm over other multicomponent isotherms is that it utilizes and leverages the single-component adsorption parameters to simulate multicomponent isotherms. The proposed JAMM analytical isotherm model furthermore incorporates the interaction between the components, a mole fraction parameter, and a heterogeneity index, providing a more comprehensive modeling framework for multicomponent adsorption. The mole fraction term was introduced for the distribution of adsorption sites based on the relative number of molecules of each component. An additional term for interaction coefficient was introduced for the representation of interactions. During the validation of JAMM with three experimental case studies with negligible, small, and high competition systems of adsorbates, impressive predictions were exhibited, with the average normalized absolute percentage error as 6.05% and average R2 as 0.86, highlighting the model's robustness, versatility, and reliability. We propose that the new JAMM isotherm modeling framework might profoundly help in chemical engineering, environmental engineering, and materials science applications by providing a potent tool for analyzing and predicting multicomponent adsorption systems.
RESUMEN
Functional surfaces and polymers with branched structures have a major impact on physicochemical properties and performance of membrane materials. With the aim of greener approach for enhancement of permeation, fouling resistance and detrimental heavy metal ion rejection capacity of polyetherimide membrane, novel grafting of poly (4-styrenesulfonate) brushes on low cost, natural bentonite was carried out via distillation-precipitation polymerisation method and employed as a performance modifier. It has been demonstrated that, modified bentonite clay exhibited significant improvement in the hydrophilicity, porosity, and water uptake capacity with 3 wt. % of additive dosage. SEM and AFM analysis showed the increase in macrovoides and surface roughness with increased additive concentration. Moreover, the inclusion of modified bentonite displayed an increase in permeation rate and high anti-irreversible fouling properties with reversible fouling ratio of 75.6%. The humic acid rejection study revealed that, PEM-3 membrane having rejection efficiency up to 87.6% and foulants can be easily removed by simple hydraulic cleaning. Further, nanocomposite membranes can be significantly employed for the removal of hazardous heavy metal ions with a rejection rate of 80% and its tentative mechanism was discussed. Conspicuously, bentonite clay-bearing poly (4-styrenesulfonate) brushes are having a synergistic effect on physicochemical properties of nanocomposite membrane to enhance the performance in real field applications.