RESUMEN
In the actual context of growing concerns over sustainability and energy efficiency, Phase Change Materials (PCMs) have gained attention as promising solutions for enhancing energy storage and release efficiency. On another hand, materials based on graphene oxide (GO) have proven antibacterial activity, biocompatibility, efficiency in microbial growth inhibition, and pollutant removal. Integrating nanoparticles into PCMs and creating Nano-Enhanced Phase Change Materials (NEPCMs) have opened new horizons for optimizing the performance of these systems and sustainable development. The key objective of this work is to gain insight into NECPMs, which are used in solar wall systems to enhance solar energy storage. Paraffin RT31 was mixed with Cu nanoparticles, graphene oxide (GO), and Cu-decorated GO (Cu@GO) at loading ratios ranging from 1% to 4% (w/w nanoparticles with respect to RT31). The compositions were characterized through Differential Scanning Calorimetry (DSC) and rheology tests. The decoration of the carbon-based nanoparticles was performed using the ultrasonication procedure, and the decoration efficiency was confirmed through X-ray Photoelectron Spectroscopy (XPS). The rheologic measurements were performed to correlate the flow behavior of the NEPCM with their composition at various temperatures. The study methodically investigated these composites' latent heat values, phase change peak temperatures, and solidification phase change temperatures. Compared to pure paraffin, the solidification of the formulations obtained using Cu@GO exhibits the largest increase in latent heat, with a 12.07% growth at a concentration of 2%. Additionally, at a 4% concentration of NEPCM, the largest increase in thermal conductivity was attained, namely 12.5%.
RESUMEN
The study presents a new analytical model capable to reveal the thermal behaviour of all the components of the solar ammonia-water absorption system, powered by parabolic trough collectors, serving different types of food storages: refrigeration chamber, refrigerated food storage, freezing chamber and frozen food storage. The heat inputs, that determine the total cooling load, for each food storage spaces consist of: heat gains through walls, heat gains through ventilation (fresh air), heat that must be dissipated from the stored products (technological cooling load required to cool down the products) and heat gains through operation. The influence of the number of solar parabolic trough collectors and of the storage tank size on different parameters of the refrigeration plant are investigated under low and high storage temperatures.â¢Food cooling with solar absorption refrigeration system.â¢Hourly based variation of NH3-H2O solar absorption system performances.â¢Long term simulation of solar absorption cooling for refrigeration and cooling.
RESUMEN
The paper proposed an alternative optical metrology to classical methods (strain gauge measurements and numerical simulation) for strain determination on printed circuit board (PCBs) due to thermal loads. The digital image correlation (DIC) technique was employed to record the strain distribution in some particular areas of the PCB. A thermal load was applied using a heating chamber, and the measurements were performed at four different temperature steps (25 °C, 50 °C, 85 °C and 120 °C). An increase in the principal strains with temperature was observed. For validation, the principal strains on the PCB obtained with DIC were compared with the values from gauge strain measurements and numerical simulation. The conclusions highlighted that DIC represents a technique with potential for strain measurement caused by thermal deformation, with the advantages of full field measurement, less preparation of the surface and good accuracy.
RESUMEN
The study proposes a method for preliminary and estimative sizing of the main components of solar district heating systems, with seasonal thermal storage. The main parameters determined by this method, are the aperture area of the solar thermal collectors and the volume of the seasonal thermal storage. The proposed method is only estimative, but it provides the necessary input data for the investigation ofthe dynamic thermal behavior of such systems. The main advantage of the method is that it requires only very few and accessible input data. Two situations are considered: the first in which available climatic data such as annual global solar radiation on horizontal plane and annual average temperature can be used in calculations, and the second in which such data is not available and should be determined through interpolation. With the proposed interpolation functions the annual global solar radiation on horizontal plane, the annual average temperature and the annual global efficiency of the solar thermal collectors were determined. The errors of the estimations are ranging within the intervals of (-15.6 +25.8) % for annual global solar radiation on horizontal plane and (-10.8 19.1) % for annual global efficiency of the solar thermal collectors. The maximum deviations for the annual average temperature estimations were (-4.23 +5.37) °C. With this limited accuracy, the proposed interpolation functions can be used for latitudes between (0-70) °, annual global solar radiation on horizontal plane between (704-2337) kWh/m2/year and annual average temperatures ranging within the interval of (2-30) °C.