RESUMEN
An experimental setup, making use of a Flash DSC 1 prototype, is presented in which materials can be studied simultaneously by fast scanning calorimetry (FSC) and synchrotron wide angle X-ray diffraction (WAXD). Accumulation of multiple, identical measurements results in high quality, millisecond WAXD patterns. Patterns at every degree during the crystallization and melting of high density polyethylene at FSC typical scanning rates from 20 up to 200 °C s(-1) are discussed in terms of the temperature and scanning rate dependent material crystallinities and crystal densities. Interestingly, the combined approach reveals FSC thermal lag issues, for which can be corrected. For polyamide 11, isothermal solidification at high supercooling yields a mesomorphic phase in less than a second, whereas at very low supercooling crystals are obtained. At intermediate supercooling, mixtures of mesomorphic and crystalline material are generated at a ratio proportional to the supercooling. This ratio is constant over the isothermal solidification time.
Asunto(s)
Rastreo Diferencial de Calorimetría , Polietileno/química , Poliestirenos/química , Difracción de Rayos X , CristalizaciónRESUMEN
A novel, powerful analytical technique, preparative temperature rising elution fractionation (prep TREF)/high-temperature (HT)-HPLC/Fourier transform infrared spectroscopy (FTIR)/high-performance differential scanning calorimetry (HPer DSC)), has been introduced to study the correlation between the polymer chain microstructure and the thermal behaviour of various components in a complex impact polypropylene copolymer (IPC). For the comprehensive analysis of this complex material, in a first step, prep TREF is used to produce less complex but still heterogeneous fractions. These chemically heterogeneous fractions are completely separated by using a highly selective chromatographic separation method--high-temperature solvent gradient HPLC. The detailed structural and thermal analysis of the HPLC fractions was conducted by offline coupling of HT-HPLC with FTIR spectroscopy and a novel DSC method--HPer DSC. Three chemically different components were identified in the mid-elution temperature TREF fractions. For the first component, identified as isotactic polypropylene homopolymer by FTIR, the macromolecular chain length is found to be an important factor affecting the melting and crystallisation behaviour. The second component relates to ethylene-propylene copolymer molecules with varying ethylene monomer distributions and propylene tacticity distributions. For the polyethylene component (last eluting component in all semi-crystalline TREF fractions), it was found that branching produced defects in the long crystallisable ethylene sequences that affected the thermal properties. The different species exhibit distinctively different melting and crystallisation behaviour, as documented by HPer DSC. Using this novel approach of hyphenated techniques, the chain structure and melting and crystallisation behaviour of different components in a complex copolymer were investigated systematically.
RESUMEN
In order to fully exploit the graft copolymer poly(ethyleneglycol-g-vinylalcohol) (EG/VA) in the formulation of solid dispersions, a characterization of its phase behavior before, during and after spray-drying and hot-melt extrusion is performed. Solid state characterization was performed using MDSC and XRPD. The effect of heating/cooling rate on the degree of crystallinity was studied using HPer DSC and ultra-fast chip calorimetry. EG/VA consists of two semi-crystalline fractions, one corresponding to the polyethyleneglycol (PEG) fraction (T(g)=-57 degrees C, T(m)=15 degrees C) and one corresponding to the polyvinylalcohol (PVA) fraction (T(g)=45 degrees C, T(m)=212 degrees C). XRPD analysis confirmed its semi-crystallinity, and EG/VA showed Bragg reflections comparable to those of PVA. Spray-drying at a temperature lower than 170 degrees C resulted in amorphization of the PVA fraction, while after hot-melt extrusion at different temperatures, the crystallinity of this fraction increases. In both cases, the PEG fraction is not influenced. Plasticization of the amorphous domains of the PEG or PVA fraction of the copolymer was dependent on the type and concentration of plasticizer, suggesting that also other small organic molecules like drugs may not homogeneously mix with both amorphous domains. A controlled cooling rate of 3000 degrees C/s was necessary to make the copolymer completely amorphous.