RESUMEN
13-93 bioglass (BG) scaffolds reinforced with graphene oxide (GO) were fabricated by robocasting (direct-ink-writing) technique. Composite scaffolds with 0-4 vol% content of GO platelets were printed, and then consolidated by pressureless spark plasma sintering at 650⯰C. It was found that, despite hampering densification of the bioglass, the addition of GO platelets up to a certain content enhanced the mechanical performance of the 13-93 bioglass scaffolds in terms of strength and, especially, toughness. Best performance was obtained for 2â¯vol.% GO, which increased strain energy density (toughness) of the scaffolds by â¼894%, and their compressive strength by â¼26%. At higher contents, agglomeration of the nanoplatelets and increased porosity significantly reduced the mechanical enhancement obtained. Implications of the results on the fabrication of novel bioglass scaffolds that may find use in load-bearing bone tissue engineering applications are discussed.
Asunto(s)
Sustitutos de Huesos , Huesos/química , Cerámica/química , Grafito/química , Ingeniería de Tejidos/métodos , Andamios del Tejido , Carboximetilcelulosa de Sodio/química , Fuerza Compresiva , Humanos , Ensayo de Materiales , Microscopía Electrónica de Rastreo , Nanotecnología , Porosidad , Reología , Difracción de Rayos XRESUMEN
Ring-opening polymerization of ε-caprolactone (ε-CL) and L-lactide (LLA) was performed to impregnate ß-tricalcium phosphate (ß-TCP) scaffolds fabricated by robocasting. Concentrated colloidal inks prepared from ß-TCP commercial powders were used to fabricate porous structures consisting of a 3D mesh of interpenetrating rods. ε-CL and LLA were in situ polymerized within the ceramic structure by using a lipase and stannous octanoate, respectively, as catalysts. The results show that both the macropores inside the ceramic mesh and the micropores within the ceramic rods are full of polymer in either case. The mechanical properties of scaffolds impregnated by in situ polymerization (ISP) are significantly increased over those of the bare structures, exhibiting similar values than those obtained by other, more aggressive, impregnation methods such as melt-immersion (MI). ISP using enzymatic catalysts requires a reduced processing temperature which could facilitate the incorporation of growth factors and other drugs into the polymer composition, thus enhancing the bioactivity of the composite scaffold. The implications of these results for the optimization of the mechanical and biological performance of scaffolds for bone tissue engineering applications are discussed.
Asunto(s)
Fosfatos de Calcio/química , Polimerizacion , Ingeniería de Tejidos/métodos , Andamios del Tejido/química , Fuerza Compresiva , Ensayo de Materiales , Microscopía Electrónica de Rastreo , Poliésteres/química , Estrés MecánicoRESUMEN
The effect of polymer infiltration on the compressive strength of ß-tricalcium phosphate (TCP) scaffolds fabricated by robocasting (direct write assembly) is analyzed in this work. Porous structures consisting of a tetragonal three-dimensional mesh of interpenetrating rods were fabricated from concentrated TCP inks with suitable viscoelastic properties. Biodegradable polymers (polylactic acid (PLA) and poly(ε-caprolactone) (PCL)) were infiltrated into selected scaffolds by immersion of the structure in a polymer melt. Infiltration increased the uniaxial compressive strength of these model scaffolds by a factor of three (PCL) or six (PLA). It also considerably improved the mechanical integrity of the structures after initial cracking, with the infiltrated structure retaining a significant load-bearing capacity after fracture of the ceramic rods. The strength improvement in the infiltrated scaffolds was attributed to two different contributions: the sealing of precursor flaws in the ceramic rod surfaces and the partial transfer of stress to the polymer, as confirmed by finite element analysis. The implications of these results for the mechanical optimization of scaffolds for bone tissue engineering applications are discussed.