RESUMEN

An approach is established for fabricating high-strength and high-stiffness composite laminates with continuous carbon nanotube (CNT) yarns for scaled-up mechanical tests and potential aerospace structure applications. Continuous CNT yarns with up to 80% degree of nanotube alignment and a unique self-assembled graphitic CNT packing result in their specific tensile strengths of 1.77 ± 0.07 N/tex and an apparent specific modulus of 92.6 ± 3.2 N/tex. Unidirectional CNT yarn reinforced composite laminates with a CNT concentration of greater than 80 wt % and minimal microscale voids are fabricated using filament winding and aerospace-grade resin matrices. A specific tensile strength of up to 1.71 GPa/(g cm-3) and specific modulus of 256 GPa/(g cm-3) are realized; the specific modulus exceeds current state-of-the-art unidirectional carbon fiber composite laminates. The specific modulus of the laminates is 2.76 times greater than the specific modulus of the constituent CNT yarns, a phenomenon not observed in carbon fiber reinforced composites. The results demonstrate an effective approach for fabricating high-strength CNT yarns into composites for applications that require specific tensile modulus properties that are significantly beyond state-of-the-art carbon fiber composites and potentially open an unexplored performance region in the Ashby chart for composite material applications.

RESUMEN

As the aerospace industry is increasingly demanding stronger, lightweight materials, ultra-strong carbon nanotube (CNT) composites with highly aligned CNT network structures could be the answer. In this work, a novel methodology applying topological data analysis (TDA) to scanning electron microscope (SEM) images was developed to detect CNT orientation. The CNT bundle extensions in certain directions were summarized algebraically and expressed as visible barcodes. The barcodes were then calculated and converted into the total spread function, V(X, θ), from which the alignment fraction and the preferred direction could be determined. For validation purposes, the random CNT sheets were mechanically stretched at various strain ratios ranging from 0 to 40%, and quantitative TDA was conducted based on the SEM images taken at random positions. The results showed high consistency (R2 = 0.972) compared to Herman's orientation factors derived from polarized Raman spectroscopy and wide-angle X-ray scattering analysis. Additionally, the TDA method presented great robustness with varying SEM acceleration voltages and magnifications, which might alter the scope of alignment detection. With potential applications in nanofiber systems, this study offers a rapid and simple way to quantify CNT alignment, which plays a crucial role in transferring the CNT properties into engineering products.

RESUMEN

Huntsman-Merrimack MIRALON® carbon nanotubes (CNTs) are a novel, highly entangled, commercially available, and scalable format of nanotubes. As-received and acid-treated CNTs were added to aerospace grade epoxy (CYCOM® 977-3), and the composites were characterized. The epoxy resin is expected to infiltrate the network of the CNTs and could improve mechanical properties. Epoxy composites were tested for flexural and viscoelastic properties and the as-received and acid treated CNTs were characterized using Field-Emission Scanning and Transmission Electron Microscopy, X-Ray Photoelectron Spectroscopy, and Thermogravimetric Analysis. Composites containing 0.4 wt% as-received CNTs showed an increase in flexural strength, from 136.9 MPa for neat epoxy to 147.5 MPa. In addition, the flexural modulus increased from 3.88 GPa for the neat epoxy to 4.24 GPa and 4.49 GPa for the 2.0 wt% and 3.0 wt% as-received CNT/epoxy composites, respectively. FE-SEM micrographs indicated good dispersion of the CNTs in the as-received CNT/epoxy composites and the 10 M nitric acid 6 h treatment at 120 °C CNT/epoxy composites. CNTs treated with 10 M nitric acid for 6 h at 120 °C added oxygen containing functional groups (C-O, C=O, and O=C-O) and removed iron catalyst present on the as-received CNTs, but the flexural properties were not improved compared to the as-received CNT/epoxy composites.

RESUMEN

Microstructures of typical carbon fibers (CFs) from polyacrylonitrile (PAN) and pitch-based precursors were studied using a novel digital twin approach with individual carbon fibers for a local crystal scale model. The transmission electron microscopy (TEM) samples were prepared using a focused-ion beam (FIB) for both longitudinal and transverse directions of carbon fibers. Measurements of the crystal size and orientation were estimated from X-ray scattering. TEM imaging of graphitic packing facilitated further comprehension of associations between processing and final material properties, which could enable customization of microstructures for property targets. Then the detailed microstructural information and their X-ray scattering properties were incorporated into the simulation model of an individual carbon fiber. Assuming that graphene properties are the same among different forms of carbon fiber, a reasonable physics-based explanation for such a drastic decrease in strength is the dislocations between the graphitic units. The model reveals critical defects and uncertainty of carbon fiber microstructures, including skin/core alignment differences and propagating fracture before ultimate failure. The models are the first to quantify microstructures at the crystal scale with micromechanics and to estimate tensile and compressive mechanical properties of carbon fiber materials, as well as potentially develop new fundamental understandings for tailoring carbon fiber and composites properties.

RESUMEN

Double-walled carbon nanotubes (DWCNTs) were synthesized and continuously collected using a water-assisted floating catalyst chemical vapor deposition (FCCVD) method. Differing from the conventional water-assisted synthesis in which water vapor is one part of the carrier gas mixture, we included de-ionized water in the catalyst system, which achieved a more uniform and controlled distribution for efficient DWCNT production. Using a water-assisted FCCVD process with optimized conditions, a transition from multi- to double-walled CNTs was observed with a decrease in diameters from 19-23 nm to 10-15 nm in tandem with an elevated Raman IG/ID ratio up to 10.23, and corroborated from the decomposition peak shifts in thermogravimetric data. To characterize the mechanical and electrical improvements, the FCCVD-CNT/bismaleimide (BMI) composites with different water concentrations were manufactured, revealing high electrical conductivity of 1720 S/cm along the bundle alignment (collection) direction, and the nano-indentation tests showed an axial reduced modulus at 65 GPa. A consistent value of the anisotropic ratio at ~3 was observed comparing the longitudinal and transverse properties. The continuous capability of the presented method while maintaining high quality is expected to result in an improved DWCNT mass production process and potentially enhance the structural and electrical applications of CNT nanocomposites.

RESUMEN

Disordered packings of colloidal spheres show angle-independent structural color when the particles are on the scale of the wavelength of visible light. Previous work has shown that the positions of the peaks in the reflectance spectra can be predicted accurately from a single-scattering model that accounts for the effective refractive index of the material. This agreement shows that the main color peak arises from short-range correlations between particles. However, the single-scattering model does not quantitatively reproduce the observed color: the main peak in the reflectance spectrum is much broader and the reflectance at low wavelengths is much larger than predicted by the model. We use a combination of experiment and theory to understand these features. We find that one significant contribution to the breadth of the main peak is light that is scattered, totally internally reflected from the boundary of the sample, and then scattered again. The high reflectance at low wavelengths also results from multiple scattering but can be traced to the increase in the scattering cross section of individual particles with decreasing wavelength. Both of these effects tend to reduce the saturation of the structural color, which limits the use of these materials in applications. We show that while the single-scattering model cannot reproduce the observed saturations, it can be used as a design tool to reduce the amount of multiple scattering and increase the color saturation of materials, even in the absence of absorbing components.

RESUMEN

The inter-particle interference of lignocellulosic materials describes the order of the macromolecules at a larger size scale, which can give information about the pore structure, and interface of cellulose and lignin. The pore structure and interface influence the rate of enzymatic hydrolysis and thermal decomposition in cellulosic ethanol manufacturing. In this study, the inter-particle interference of cellulose and lignin of three major categories of lignocellulosic materials: wood-based (cedar and oak), energy crop (bamboo), and agricultural or forestry waste (palm) were evaluated. Scanning electron microscopy (SEM) reveals morphological irregularities in the case of bamboo and palm, which may form nucleation sites for faster accessibility to enzyme molecules. Small-angle X-ray scattering (SAXS) shows increased power-law exponent for palm, suggesting a less clustered structure, which was consistent with the rough surface morphology as detected by the SEM. Differential Scanning Calorimetry (DSC) showed a higher temperature maximum for cedar and oak, which is indicative of higher intermolecular forces within their organic compounds, and could result in slower disintegration of the macromolecules during biochemical processing. This study will help to estimate the activity of the macromolecules and absorption capacity of lignocellulosic materials during biochemical processing.

Asunto(s)

RESUMEN

The study of lignocellulosic materials calls for understanding the structure, and function of different cellulosic materials from diverse sources to scale-up cellulosic ethanol production. For the first time, a systematic assessment of the molecular and supramolecular structure highlighting the similarities and dissimilarities of three major categories of lignocellulosic materials: wood-based (cedar and oak), energy crop (bamboo), and agricultural or forestry waste (palm) are reported. The cellulose, hemicellulose, and lignin constituents were compared for their suitability in cellulosic ethanol production. FTIR showed structural variations within the functional groups with notable OH group in the palm and CC group in cedar. From the X-ray scattering, bamboo exhibited the highest crystallinity (49.5%), and palm showed the lowest crystallinity (22.6%) and crystallite size (2.6 nm). TGA revealed high cellulose amount and stable structure for cedar and oak, and the most unstable structure in the palm, which indicates a better cellulose/hemicellulose accessibility and biodegradability for enzymatic or chemical action in the palm. This comparative assessment can greatly facilitate material selection and component mixture, for developing an efficient and cost-effective biochemical process in ethanol manufacturing.

Asunto(s)

RESUMEN

This paper presents simulation results for double nanohole and inverted bowtie nanoapertures optimized to resonate in the short-wave infrared regime (1050 nm and 1550 nm). These geometries have shown great promise for trapping nanoparticles with applications in optical engineering, physics, and biology. Using a finite element analysis tool, we found that the outline length for inverted bowtie nanoapertures in a 100 nm thick gold film with a 20 nm gap dimension having an optimized transmission resonance for 1050 nm and 1550 nm optical wavelengths is 106.5 nm and 188.5 nm, respectively. With the same gap size, the radii of the circles for the double nanohole nanoapertures are 72 nm and 128 nm. The near-field enhancements of the two structures are almost the same, while the double nanohole geometries have a 20% larger full width at half-maximum than the inverted bowtie. Next, by studying the effect of changing the inner radii of the inverted bowtie corners, we found that the difference between 2 nm and 6 nm corner radii can blue-shift the optical resonance by up to 45 nm. As a result of not having any inner corners, the double nanohole structure requires less precise fabrication and therefore could potentially have a higher successful yield of nanoapertures during the manufacturing process. Lastly, we will show experimental results that confirm the optical resonance of the nanoapertures at 1550 nm. These results will enable better performance and signal-to-noise ratio in nanoaperture trapping for the short-wave infrared wavelength regime.

RESUMEN

Stretchable materials are indispensable for applications such as deformable devices, wearable electronics, and future robotics. However, designs for new elastomers with high stretchability have undergone only limited research. Here we have fabricated highly stretchable Ag+/polyacrylonitrile elastomer with nanoreservoirs of lubricant using cyano-silver complexes. The prepared products feature nanoconfinement structures of lubricant surrounded by polymer chains with coordination bond through chelates of cyano-silver, resulting in an enhanced stretchability of more than 600% from 2%. The elastomeric properties were investigated, and a mechanical response model was proposed, which explained the structural evolution including the polymer chain fluidity under external deformation. Also, the easy breakage and dynamic reformation of cyano-silver coordination complexes promises a strain recovery under various stretching conditions. This elastomer itself can directly work as sensors and open paths to alternative substrates for soft electronics development.

RESUMEN

Colloidal particles with a repulsive interparticle potential spontaneously form crystalline lattices, which are used as a motif for photonic materials. It is difficult to predict the crystal arrangement in spherical volume as lattices are incompatible with a spherical surface. Here, the optimum arrangement of charged colloids is experimentally investigated by encapsulating them in double-emulsion drops. Under conditions of strong interparticle repulsion, the colloidal crystal rapidly grows from the surface toward the center of the microcapsule, forming an onion-like arrangement. By contrast, for weak repulsion, crystallites slowly grow and fuse through rearrangement to form a single-crystal phase. Single-crystal structure is energetically favorable even for strong repulsion. Nevertheless, a high energy barrier to colloidal rearrangement kinetically arrests the onion-like structure formed by heterogeneous nucleation. Unlike the isotropic onion-shaped product, the anisotropic single-crystal-containing microcapsules selectively display-at certain orientations but not others-one of the distinct colors from the various crystal planes.

RESUMEN

Technologies to monitor microenvironmental conditions and its spatial distribution are in high demand, yet remain unmet need. Herein, photonic microsensors are designed in a capsule format that can be injected, suspended, and implanted in any target volume. Colorimetric sensors are loaded in the core of microcapsules by assembling core-shell colloids into crystallites through the depletion attraction. The shells of the colloids are made of a temperature-responsive hydrogel, which enables the crystallites to rapidly and widely tune the structural color in response to a change in temperature while maintaining close-packed arrays. The spherical symmetry of the microcapsules renders them optically isotropic, i.e., displaying orientation-independent color. In addition, as a solid membrane is used to protect the delicate crystallites from external stresses, their high stability is assured. More importantly, each microcapsule reports the temperature of its microenvironment so that a suspension of capsules can provide information on the spatial distribution of the temperature.

RESUMEN

Free-standing carbon nanotube films or buckypaper can provide a significant platform to develop practical applications of nanocarbon materials. For this research, buckypaper with high thermal conductivity (20 W/m K) and large surface area (350 m2/g) was mass produced in-house to investigate for use in lightweight thermal management devices. Floating catalyst chemical vapor deposition carbon nanotube sheets were also studied in this work. We introduced two manufacturing techniques to use the sheets for heat dissipation: (1) printing conductive composite ink on the sheets to make lightweight thermal devices, such as heat sinks and (2) assembling the sheets directly into 3D structures that were mounted on the back of heat-generating devices. These manufacturing techniques resulted in extremely lightweight, high-performance heat dissipation devices compared with other heat sink materials.

RESUMEN

Large scale manufacturing of electrically conductive carbon nanotube (CNT) sheets with production capability, low cost, and long-term electrical performance stability is still a challenge. A new method to fabricate highly conductive continuous buckypaper (CBP) with roll-to-roll production capability and relatively low cost is reported. The electrical conductivity of CBP can be improved to 7.6 × 104 S m-1 by using an oxidant chemical (i.e. HNO3 and I2) doping method. To compensate for the conductivity degradation caused by the instability of the oxidant chemical doping, a polymer layer of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) was coated on the chemically doped CBP. The fabricated highly conductive CBP showed stable electrical performance in air for more than a month. This CBP material with high electrical conductivity, relatively low cost, and roll-to-roll manufacturing capability could enable a wide range of engineering applications including flexible conductors, electromagnetic interference (EMI) shielding materials, and electrodes in energy devices.

RESUMEN

AIMS: Although circumferential pulmonary vein isolation (CPVI) has been considered as the cornerstone for paroxysmal atrial fibrillation (PAF) ablation, there has been a substantial recurrence rate. We conducted a prospectively randomized study to evaluate whether additional linear ablation from the superior vena cava (SVC) to the right atrial (RA) septum (SVC-L) improves the clinical outcome. METHODS AND RESULTS: This study enroled 200 patients with PAF (male 74.5%, 56.8 ± 11.7 years old) randomly assigned to either the CPVI (n = 100) or CPVI + SVC-L (n = 100) groups. An RA isthmus ablation was performed in all patients. The CPVI + SVC-L group required a longer ablation procedure time (82.7 ± 17.9 min) than the CPVI group (63.6 ± 16.8 min, P < 0.001). The complication rates were 5% in CPVI + SVC-L group and 2% in CPVI group, respectively (P = 0.445). Two CPVI + SVC-L group patients had post-procedural sinus node dysfunction, which recovered within 24 h. During 12.2 ± 5.3 months of follow-up, the recurrence rate was significantly lower in the CPVI + SVC-L group (6%) than the CPVI group (27%, P < 0.001). The post-procedural 3-month follow-up heart rate variability in the CPVI + SVC-L group showed a significantly greater reduction in the rMSSD (25.2 ± 13.7 vs. 13.7 ± 8.5 ms, P < 0.001), HF (10.2 ± 7.1 vs. 5.5 ± 5.8 ms(2), P < 0.001), and LF/HF (1.6 ± 0.5 vs. 0.9 ± 0.3, P < 0.001) than in the CPVI group. CONCLUSION: In spite of a longer procedure time and risk of transient sinus node dysfunction, an SVC-L in addition to CPVI improved the clinical outcome of catheter ablation, and was associated with post-procedural autonomic neural remodelling in patients with PAF.

Asunto(s)

Asunto(s)

RESUMEN

Structurally colored materials could potentially replace dyes and pigments in many applications, but it is challenging to fabricate structural colors that mimic the appearance of absorbing pigments. We demonstrate the microfluidic fabrication of "photonic pigments" consisting of microcapsules containing dense amorphous packings of core-shell colloidal particles. These microcapsules show non-iridescent structural colors that are independent of viewing angle, a critical requirement for applications such as displays or coatings. We show that the design of the microcapsules facilitates the suppression of incoherent and multiple scattering, enabling the fabrication of photonic pigments with colors spanning the visible spectrum. Our findings should provide new insights into the design and synthesis of materials with structural colors.

RESUMEN

Colloidal crystals are promising structures for photonic applications requiring dynamic control over optical properties. However, for ease of processing and reconfigurability, the crystals should be encapsulated to form 'ink' capsules rather than confined in a thin film. Here we demonstrate a class of encapsulated colloidal photonic structures whose optical properties can be controlled through osmotic pressure. The ordering and separation of the particles within the microfluidically created capsules can be tuned by changing the colloidal concentration through osmotic pressure-induced control of the size of the individual capsules, modulating photonic stop band. The rubber capsules exhibit a reversible change in the diffracted colour, depending on osmotic pressure, a property we call osmochromaticity. The high encapsulation efficiency and capsule uniformity of this microfluidic approach, combined with the highly reconfigurable shapes and the broad control over photonic properties, make this class of structures particularly suitable for photonic applications such as electronic inks and reflective displays.

RESUMEN

Colloidal glasses, bird feathers, and beetle scales can all show structural colors arising from short-ranged spatial correlations between scattering centers. Unlike the structural colors arising from Bragg diffraction in ordered materials like opals, the colors of these photonic glasses are independent of orientation, owing to their disordered, isotropic microstructures. However, there are few examples of photonic glasses with angle-independent red colors in nature, and colloidal glasses with particle sizes chosen to yield structural colors in the red show weak color saturation. Using scattering theory, we show that the absence of angle-independent red color can be explained by the tendency of individual particles to backscatter light more strongly in the blue. We discuss how the backscattering resonances of individual particles arise from cavity-like modes and how they interact with the structural resonances to prevent red. Finally, we use the model to develop design rules for colloidal glasses with red, angle-independent structural colors.

Asunto(s)

RESUMEN

OBJECTIVE: This study simultaneously addresses the issues of the scarcity of information about pediatric patient color preferences, conflicting findings about the impact of culture on color preferences, and limitations of previous research instruments. Effects of culture and gender on color preferences were investigated using American and Korean pediatric patients. BACKGROUND: Much of the existing research in environmental design has focused on environments for healthy children and adults, but those findings cannot be confidently applied to environments for pediatric patients. In previous studies, the impact of culture on color preferences has been suggested, though the effects appear to vary. Moreover, the results of previous studies were typically based on perceptions of small color chips, which are different from seeing a color on wall surfaces. Previous studies also failed to control for confounding variables such as color attributes and light sources. METHODS: Instead of using color chips, this study used physical model simulation to investigate environmental color preferences in real contexts. RESULTS: Cultural difference was found in white. Other than white, no significant cultural difference was found. Gender differences were found across both of the groups. CONCLUSIONS: Korean pediatric patients showed significantly higher preference scores for white than Americans did. Other than white, both groups reported blue and green as their most preferred colors; white was the least preferred. Both groups reported similar gender effects. Overall, male patients reported significantly lower preference scores for red and purple than female patients did. These results can help healthcare providers and professionals better understand appropriate colors for pediatric populations. KEYWORDS: Evidence-based design, healing environment, patients, pediatric, satisfaction.

Asunto(s)