RESUMEN
OBJECTIVES: Two 3-dimensional models, one of a lower second premolar and one of a lower central incisor were used to investigate effects of load on the location and magnitude of cervical strains. METHODS: Point loads of 100 N were applied to the model premolar (at the cusp tip, parallel and 45 degrees to the long axis of the tooth) and incisor (at the mid-buccal point on incisal edge, parallel and 45 degrees to the long axis of the tooth). Outputs were presented in the form of tensile-strain contours and vector plots. RESULTS: Strains were concentrated near the cementoenamel junction (CEJ) regardless of load direction, and oblique loading showed higher tensile strains, opposite to the point of loading, than vertical loading for both models. For the premolar model, regardless of loading direction, strains were concentrated at the mid- buccal CEJ. In contrast, under vertical loading on the incisor model, tensile strains were concentrated at the line-angle of CEJ. From oblique loads, vector plots of both models showed tensile vectors in vertical directions while vertical loads showed tensile vectors in horizontal directions. CONCLUSION: Mechanisms of non-carious cervical lesions (NCCLs) may in part be due the changing orientation of tensile strains as well as their magnitude. Stress concentration at the CEJ related well to the common location of clinical NCCLs. The crown-root morphology may have an influence on the initial location of non-carious cervical lesions.
Asunto(s)
Diente Premolar/química , Análisis del Estrés Dental/métodos , Incisivo/química , Cuello del Diente/química , Diente Premolar/anatomía & histología , Fuerza Compresiva , Análisis de Elementos Finitos , Humanos , Incisivo/anatomía & histología , Modelos Dentales , Resistencia a la Tracción , Soporte de PesoRESUMEN
BACKGROUND: The marginal ridge is considered fundamental to the ability of the tooth to resist functional and parafunctional occlusal loads without damage. Despite this role, very little is known of patterns of stress and strain in marginal ridges under load. This study investigated strains in proximal enamel of mandibular premolars using finite element analysis (FEA) and strain gauge measurements. METHODS: A three-dimensional FEA model of a human mandibular premolar was developed using commercial FEA software, and strains were computed in response to loads simulating clenching and chewing functions. Strains were measured in extracted premolars using strain gauges mounted on the proximal surfaces, under similar occlusal loading conditions. RESULTS: Strains in the vicinity of contact areas and marginal ridges were lower than near the cemento-enamel junction and on buccal and lingual surfaces. The magnitude of proximal strains increased with oblique loading on cuspal inclines. Finite element analysis results correlated well with strain gauge measurements and can be used to predict strain directions and magnitudes. CONCLUSIONS: At least for mandibular premolars, the marginal ridges are not highly stressed areas during simulated occlusal loading.
Asunto(s)
Diente Premolar/fisiología , Fuerza de la Mordida , Esmalte Dental/fisiología , Corona del Diente/fisiología , Análisis de Varianza , Diente Premolar/anatomía & histología , Bruxismo/fisiopatología , Simulación por Computador , Esmalte Dental/anatomía & histología , Análisis de Elementos Finitos , Humanos , Mandíbula , Masticación/fisiología , Modelos Biológicos , Estrés Mecánico , Cuello del Diente/anatomía & histología , Cuello del Diente/fisiología , Corona del Diente/anatomía & histología , Soporte de PesoRESUMEN
OBJECTIVES: This study was designed to measure the dissolution of buccal enamel of extracted teeth exposed to acid with or without simultaneous cyclic occlusal loading. METHODS: Twenty mandibular premolars were mounted in pairs in a servohydraulic testing machine, and immersed in 1% lactic acid (pH 4.5) or water. One tooth of each pair was subjected to cyclic loading (100 N at 2 Hz for 200,000 cycles), with the load applied at 45 degrees to the tooth axis on the buccal incline of the buccal cusp. The second tooth of each pair was immersed in acid but not subjected to load. Control teeth were immersed in water, with one tooth of each pair undergoing cyclic loading. Impressions of the teeth were taken before and after exposure to acid and occlusal loading, and a profiling system was used to measure the depth and volume loss of enamel on the buccal surface. RESULTS: The depth of enamel dissolved ranged from approximately 50-200 microm. In certain locations teeth undergoing cyclic loading during acid exposure showed greater volumetric loss than teeth not subjected to load. Loaded teeth showed a complex pattern of enamel dissolution; volumetric loss in the cervical third was greater than in the middle third, and was much greater in the mesiobuccal segment (under tension) than in the distobuccal segment (under compression). Unloaded teeth showed greater volumetric loss in the cervical third than in the middle third, with a uniform pattern of enamel dissolution from mesiobuccal to distobuccal aspects. SIGNIFICANCE: Enamel dissolution is increased significantly in sites subjected to cyclic tensile load.
Asunto(s)
Fuerza de la Mordida , Solubilidad del Esmalte Dental/fisiología , Esmalte Dental/fisiopatología , Ácido Láctico/efectos adversos , Análisis de Varianza , Diente Premolar , Esmalte Dental/efectos de los fármacos , Esmalte Dental/ultraestructura , Solubilidad del Esmalte Dental/efectos de los fármacos , Resinas Epoxi , Humanos , Concentración de Iones de Hidrógeno , Inmersión , Microscopía Electrónica de Rastreo , Técnicas de Réplica , Estadística como Asunto , Estrés Mecánico , Cuello del Diente/efectos de los fármacos , Cuello del Diente/fisiopatología , Cuello del Diente/ultraestructura , Agua , Soporte de PesoRESUMEN
OBJECTIVES: This study was planned to investigate the variations in strains in enamel under different patterns of occlusal loading, using three-dimensional finite element analysis (3D FEA) and strain gage measurements in extracted teeth. METHODS: A 3D FEA model of a mandibular second premolar was used to investigate effects of occlusal load on enamel surface strains, particularly in response to oblique directions of cuspal loading. Point loads of 100 N were applied axially and at 45 degrees from the vertical on the buccal or lingual incline of the buccal cusp, either in the bucco-lingual plane or at varying mesio-distal angulations (up to +/- 20 degrees). Patterns of strain observed in the FEA model were confirmed experimentally using strain gages on extracted premolars mounted in a servohydraulic testing machine. RESULTS: Strains predicted from the FEA model were in excellent agreement with the strain gage measurements. Strains were concentrated near the cementoenamel junction (CEJ) regardless of load direction. A vertical load on the buccal cusp tip resulted in compressive strains on the buccal surface but small tensile strains in lingual cervical enamel. Strains resulting from oblique loads on buccal cusp inclines were complex and asymmetric, with either tension or compression occurring in any location depending on the site and angle of loading. SIGNIFICANCE: The magnitude, direction and character of strains in cervical enamel are highly dependent on patterns of loading. The asymmetric pattern of strains in buccal cervical enamel in response to oblique occlusal forces is consistent with the common clinical picture of asymmetric non-carious cervical lesions.