RESUMEN
BACKGROUND: Angina is common in hypertrophic cardiomyopathy (HCM) and is associated with abnormal myocardial perfusion. Wave intensity analysis improves the understanding of the mechanics of myocardial ischemia. OBJECTIVES: Wave intensity analysis was used to describe the mechanisms underlying perfusion abnormalities in patients with HCM. METHODS: Simultaneous pressure and flow were measured in the proximal left anterior descending artery in 33 patients with HCM and 20 control patients at rest and during hyperemia, allowing calculation of wave intensity. Patients also underwent quantitative first-pass perfusion cardiac magnetic resonance to measure myocardial perfusion reserve. RESULTS: Patients with HCM had a lower coronary flow reserve than control subjects (1.9 ± 0.8 vs. 2.7 ± 0.9; p = 0.01). Coronary hemodynamics in HCM were characterized by a very large backward compression wave during systole (38 ± 11% vs. 21 ± 6%; p < 0.001) and a proportionately smaller backward expansion wave (27% ± 8% vs. 33 ± 6%; p = 0.006) compared with control subjects. Patients with severe left ventricular outflow tract obstruction had a bisferiens pressure waveform resulting in an additional proximally originating deceleration wave during systole. The proportion of waves acting to accelerate coronary flow increased with hyperemia, and the magnitude of change was proportional to the myocardial perfusion reserve (rho = 0.53; p < 0.01). CONCLUSIONS: Coronary flow in patients with HCM is deranged. Distally, compressive deformation of intramyocardial blood vessels during systole results in an abnormally large backward compression wave, whereas proximally, severe left ventricular outflow tract obstruction is associated with an additional deceleration wave. Perfusion abnormalities in HCM are not simply a consequence of supply/demand mismatch or remodeling of the intramyocardial blood vessels; they represent a dynamic interaction with the mechanics of myocardial ischemia that may be amenable to treatment.
Asunto(s)
Cardiomiopatía Hipertrófica/diagnóstico por imagen , Cardiomiopatía Hipertrófica/fisiopatología , Circulación Coronaria , Imagen por Resonancia Magnética , Isquemia Miocárdica/diagnóstico por imagen , Isquemia Miocárdica/fisiopatología , Adulto , Anciano , Velocidad del Flujo Sanguíneo , Presión Sanguínea , Técnicas de Imagen Cardíaca , Cardiomiopatía Hipertrófica/complicaciones , Femenino , Humanos , Masculino , Persona de Mediana Edad , Isquemia Miocárdica/etiología , Adulto JovenRESUMEN
AIMS: This study aimed to compare the acute expansion behaviour of a polymer-based bioresorbable scaffold and a second-generation metallic DES platform in a realistic coronary artery lesion model. Experimental mechanical data with conventional methods have so far shown little difference between metallic stents and currently available polymer-based bioresorbable scaffolds (BRS). Nevertheless, differences in acute results have been observed in clinical studies comparing BRS directly with metallic DES platforms. METHODS AND RESULTS: We examined the expansion behaviour of the bioresorbable vascular scaffold (3.0×18 mm Absorb BVS; Abbott Vascular, Santa Clara, CA, USA) and a metallic DES (3.0×18 mm XIENCE Prime; Abbott Vascular) after expansion at 37°C using identical coronary artery stenosis models (in total 12 experiments were performed). Device expansion was compared during balloon inflation and after deflation using microscopy to allow assessment of plaque recoil. Minimal lumen diameter (MLD) and minimal lumen area (MLA) and stent eccentricity were quantified from optical coherence tomography (OCT) imaging at nominal diameter and after post-dilation at 18 atm. The MLA in the models with BVS deployed was 4.92±0.17 mm² while in the metallic DES it was 5.40±0.13 mm2 (p=0.02) at nominal pressure (NP), and 5.41±0.20 and 6.07±0.25 mm2 (p=0.02), respectively, after expansion at 18 atm. Stent eccentricity index at the MLA was 0.71±0.02 in BVS compared to 0.81±0.02 in the metal stent at NP (p=0.004), and 0.73±0.03 compared to 0.75±0.02 at 18 atm (p=0.39). CONCLUSIONS: Results obtained in this in vitro lesion model were comparable to the results in randomised clinical trials comparing BVS and XIENCE stents in vivo. Such models may be useful in future BRS developments to predict their acute response in vivo in eccentric lesions.
Asunto(s)
Implantes Absorbibles , Prótesis Vascular , Enfermedad Coronaria/cirugía , Stents Liberadores de Fármacos , Andamios del Tejido , Análisis de Elementos Finitos , Humanos , HidrodinámicaRESUMEN
AIMS: Left main stenting is increasingly performed and often involves deployment of a single stent across vessels with marked disparity in diameters. Knowing stent expansion capacity is critical to ensure adequate strut apposition after post-dilatation of the stent has been performed. Coronary stents are usually manufactured in only two or three different model designs with each design having a different maximal expansion capacity. Information about the different workhorse designs and their maximal achievable diameter is not commonly provided by manufacturers but, in the absence of this critically important information, stents implanted in segments with major changes in vessel diameter have the potential to become grossly overstretched and to remain incompletely apposed. METHODS AND RESULTS: We examined the differences in workhorse designs of six commercially available drug-eluting stents (DES): the PROMUS Element, Taxus Liberté, XIENCE Prime, Resolute Integrity, BioMatrix Flex and Cypher Select stents. Using micro-computed tomography, we tested oversizing capabilities above nominal pressures for the different workhorse designs of the six DES using 4.0, 5.0 and 6.0 mm post-dilatation balloons inflated to 14 atmospheres. MLD could be increased significantly in all stents, only restricted by workhorse design limitations. Minimal inner lumen diameter (MLD) achieved after two successive 6.0 mm post-dilatations of the largest design (4.0 mm stent) was 5.7 mm for the Element, 5.6 mm for the XIENCE Prime, 6.0 mm for the Taxus, 5.4 mm for the Resolute Integrity, 5.9 mm for the BioMatrix and 5.8 mm for the Cypher stent. Significant deformations were observed during stent oversizing with large changes in terms of cell opening and crowns expansion. These are affected by design structure and reveal important differences among all stents tested. Such extensive deformations may alter the functional ability of an individual stent to scaffold a lesion and prevent restenosis. CONCLUSIONS: Stent selection based on stent model design may be critical, particularly for treatment of large artery and left main bifurcations where overexpansion is normally required to optimise results and ensure full expansion of the stent.