RESUMEN

The development of efficient and compact photonic systems in support of mid-infrared integrated optics is currently facing several challenges. To date, most mid-infrared glass-based devices are employing fluoride or chalcogenide glasses (FCGs). Although the commercialization of FCGs-based optical devices has rapidly grown during the last decade, their development is rather cumbersome due to either poor crystallization and hygroscopicity resilience or poor mechanical-thermal properties of the FCGs. To overcome these issues, the parallel development of heavy-metal oxide optical fiber from the barium-germanium-gallium oxide vitreous system (BGG) has revealed a promising alternative. However, over 30 years of fiber fabrication optimization, the final missing step of drawing BGG fibers with acceptable losses for meters-long active and passive optical devices had not yet been reached. In this article, we first identify the three most important factors that prevent the fabrication of low-loss BGG fibers i.e., surface quality, volumic striae and glass thermal-darkening. Each of the three factors is then addressed in setting up a protocol enabling the fabrication of low-loss optical fibers from gallium-rich BGG glass compositions. Accordingly, to the best of our knowledge, we report the lowest losses ever measured in a BGG glass fiber i.e., down to 200 dB km-1 at 1350 nm.

RESUMEN

We report on an ytterbium-free, erbium-doped single-mode all-fiber laser reaching a record output power of 107 W at 1598 nm, with a slope efficiency of 38.6% according to the absorbed pump power at 981 nm. The erbium-doped gain fiber, co-doped with cerium, aluminum, and phosphorus, was fabricated in-house with adjusted doping concentrations to reduce erbium ions clustering, thereby increasing efficiency while keeping the numerical aperture low to ensure a single-mode laser operation. The addition of cerium co-dopant in the core glass of an erbium system is used for the first time, to the best of our knowledge, in order to adjust the fiber's numerical aperture without increasing the erbium concentration. Numerical modeling, validated by the experimental results, demonstrates that adding aluminum and phosphorus at high concentration mitigates erbium ions clustering, with an estimated erbium paired ions of only 5.0% in the reported gain fiber.

RESUMEN

New glass compositions containing high concentrations of Tb3+ ions were developed aiming at the production of magneto-optical (MO) fibers. This work reports on the structural and MO properties of a new glass composition based on (100 - x)(41GeO2-25B2O3-4Al2O3-10Na2O-20BaO) - xTb4O7. Morphological analysis (HR-TEM) of the sample with the highest concentration of Tb3+ ions confirmed the homogeneous distribution of Tb3+ ions and the absence of nanoclusters. All the samples presented excellent thermal stability against crystallization (ΔT > 100 °C). An optical fiber was manufactured by a fiber drawing process. The UV-Vis spectra of the glasses showed Tb3+ electronic transitions and optical windows varying from 0.4 to 1.6 µm. The magneto-optical properties and the paramagnetic behaviors of the glasses were investigated using Faraday rotation experiments. The Verdet constant (VB) values were calculated at 500, 650, 880, 1050, 1330, and 1550 nm. The maximum VB values obtained at 650 and 1550 nm for the glass with x = 18 mol% were -128 and - 17.6 rad T-1 m-1, respectively. The VB values at 500 and 1550 nm for the optical fiber containing 8 mol% of Tb4O7 were - 110.2 and - 9.5 rad T-1 m-1, respectively, while the optical loss at around 880 nm was 6.4 dB m-1.

RESUMEN

In this Letter, we introduce a graded-index (GRIN)-lens combination named GRIN-axicon, which is a versatile component capable of generating high-quality scalable Bessel-Gauss beams. To the best of our knowledge, the GRIN-axicon is the only optical component that can be introduced in both larger-scale laboratory setups and miniaturized all-fiber optical setups, while having an easy control of the dimensioning of the generated focal line. We show that a GRIN lens with a hyperbolic secant refractive index profile with a sharp central dip and no ripples generates a Bessel-Gauss beam with a high-intensity central lobe when coupled to a simple lens. Such fabrication characteristics are very suitable for the modified chemical vapor deposition (MCVD) process and enable easy manufacturing of an adaptable component that can fit in any optical setup.

RESUMEN

We report on the development of a novel hybrid glass-polymer multicore fiber integrating three 80 µm polyimide-coated silica fibers inside a 750 µm polycarbonate cladding. By inscribing an array of distributed FBGs along each segment of silica fiber prior to the hybrid fiber drawing, we demonstrate a curvature sensor with an unprecedented precision of 296 pm/m-1 around 1550 nm, about 7 times more sensitive than sensors based on standard 125 µm multicore fibers. As predicted by theory, we show experimentally that the measured curvature is insensitive to temperature and strain. Also, a more precise equation to describe the curvature on a simple bending setup is presented. This new hybrid multicore fiber technology has the potential to be extended over several kilometers and can find high-end applications in 3D shape sensing and structural health monitoring.

RESUMEN

We report on an ytterbium-free erbium-doped aluminophosphosilicate all-fiber laser, producing an output power of 25 W at a wavelength of 1584 nm with a slope efficiency of 30% with respect to the 976 nm absorbed pump power. The simple cavity design proposed takes advantage of fiber Bragg gratings written directly in the gain fiber. The single-mode erbium-doped aluminophosphosilicate fiber was fabricated in-house and was doped with 0.06 mol.% of Er2O3, 1.77 mol.% of Al2O3 and 1.04 mol.% of P2O5. The incorporation of aluminium and phosphorus into the fiber core allowed for an increased concentration of erbium without inducing significant clustering, while keeping the numerical aperture low to ensure a single-mode laser operation.

RESUMEN

This paper presents the EcoChip, a new system based on the state-of-the-art electro-chemical impedance (EIS) technologies allowing the growth of single strain organisms isolated from northern habitats. This portable system is a complete and autonomous wireless platform designed to monitor and cultivate microorganisms directly sampled from their natural environment, particularly from harsh northern environments. Using 96-well plates, the EcoChip can be used in the field for real-time monitoring of bacterial growth. Manufactured with high-quality electronic components, this new EIS monitoring system is designed to function at a low excitation voltage signal to avoid damaging the cultured cells. The high-precision calibration network leads to high-precision results, even in the most limiting contexts. Luminosity, humidity, and temperature can also be monitored with the addition of appropriate sensors. Access to robust data storage systems and power supplies is an obvious limitation for northern research. That is why the EcoChip is equipped with a flash memory that can store data over long periods of time. To resolve the power issue, a low-power micro-controller and a power management unit control and supply all electronic building blocks. Data stored in the EcoChip's flash memory can be transmitted through a transceiver whenever a receiver is located within the functional transmission range. In this paper, we present the measured performance of the system, along with results from laboratory tests in vitro and from two field tests. The EcoChip has been utilized to collect bio-environemental data in the field from the northern soils and ecosystems of Kuujjuarapik and Puvirnituq, during two expeditions, in 2017 and 2018, respectively. We show that the EcoChip can effectively carry out EIS analyses over an excitation frequency ranging from 750 Hz to 10 kHz with an accuracy of 2.35%. The overall power consumption of the system was 140.4 mW in normal operating mode and 81 µW in sleep mode. The proper development of the isolated bacteria was confirmed through deoxyribonucleic acid sequencing, indicating that bacteria thrive in the EcoChip's culture wells while the growing conditions are successfully gathered and stored.

Asunto(s)

Técnicas Bacteriológicas/instrumentación , Monitoreo del Ambiente/instrumentación , Microbiología del Suelo , Microbiología del Agua , Bacillus subtilis/genética , Bacillus subtilis/aislamiento & purificación , Bacillus subtilis/fisiología , Clima , ADN Bacteriano/análisis , Espectroscopía Dieléctrica/instrumentación , Diseño de Equipo , Escherichia coli/genética , Escherichia coli/aislamiento & purificación , Escherichia coli/fisiología

RESUMEN

We report on a splice-free erbium-doped all-fiber laser emitting over 20 W at a wavelength of 1610 nm, with a slope efficiency of 19.6 % and an overall efficiency of 18.3% with respect to the launched pump power at 976 nm. The simple cavity design takes advantage of fiber Bragg gratings written directly in the gain fiber through the polymer coating and clad-pumping from a single commercial pump diode to largely simplify the assembling process, making this cavity ideal for large-scale commercial deployment. Two single-mode and singly erbium-doped silica fibers were fabricated in-house: the first to assess the effects of a high erbium concentration (0.36 mol.% Er2O3), yielding a low efficiency of 2.5 % with respect to launched pump power, and the second to achieve the improved result mentioned above (0.03 mol.% Er2O3). Numerical simulations show the link between the performance of each cavity and ion pair-induced quenching.

RESUMEN

In recent years, the fabrication of multifunctional fibers has expanded for multiple applications that require the transmission of both light and electricity. Fibers featuring these two properties are usually composed either of a single material that supports the different characteristics or of a combination of different materials. In this work, we fabricated (i) novel single-core step-index optical fibers made of electrically conductive AgI-AgPO3-WO3 glass and (ii) novel multimaterial fibers with different designs made of AgI-AgPO3-WO3 glass and optically transparent polycarbonate and poly (methyl methacrylate) polymers. The multifunctional fibers produced show light transmission over a wide range of wavelengths from 500 to 1000 nm for the single-core fibers and from 400 to 1000 nm for the multimaterial fibers. Furthermore, these fibers showed excellent electrical conductivity with values ranging between 10-3 and 10-1 S·cm-1 at room temperature within the range of AC frequencies from 1 Hz to 1 MHz. Multimodal taper-tipped fibre microprobes were then fabricated and were characterized. This advanced design could provide promising tools for in vivo electrophysiological experiments that require light delivery through an optical core in addition to neuronal activity recording.

RESUMEN

As2S3 glass has a unique combination of optical properties, such as wide transparency in the infrared region and a high nonlinear coefficient. Recently, intense research has been conducted to improve photonic devices using thin materials. In this Letter, highly uniform rectangular single-index and 2 dB/m loss step-index optical tapes have been drawn by the crucible technique. Low-loss (<0.15 dB/cm) single-mode waveguides in chalcogenide glass tapes have been fabricated using femtosecond laser writing. Optical backscatter reflectometry has been used to study the origin of the optical losses. A detailed study of the laser writing process in thin glass is also presented to facilitate a repeatable waveguide inscription recipe.