RESUMEN
In awareness of industrial dye wastewater, carbon quantum dots (CQDs) and cobalt zinc ferrite (CZF) nanocomposites were synthesised for the making of carbon quantum dots coated cobalt zinc ferrite (CZF@CQDs) nanophotocatalyst using oxidative polymerization reaction. The results of TEM, zeta potential value, and FTIR confirm highly dispersed 1-4 nm particles with the - 45.7 mV carboxylic functionalized surface of CQDs. The results of the synthesised CZF@CQDs photocatalyst showed an average particle size of ~ 15 nm according to TEM, SEM, and XRD. The photocatalyst showed a 1.20 eV band gap, which followed the perfect visible light irradiation. TGA and DTA revealed the good thermal stability of the nanophotocatalyst. VSM was carried out, and the saturation magnetisations for CZF and CZF@CQDs were 42.44 and 36.14 emu/g, respectively. A multipoint study determined the BET-specific surface area of the CZF@CQDs photocatalyst to be 149.87 m2/g. Under visible light irradiation, the final CZF@CQDs nanophotocatalyst demonstrated remarkable efficiency (~ 95% within 25 min) in the photocatalytic destruction of Reactive Blue 222 (RB 222) and Reactive Yellow 145 (RY 145) dyes, as well as mechanical stability and recyclability. Even after the recycling of the degradation study, the nanophotocatalyst efficiency (~ 82%, 7th cycles) was predominantly maintained. The effects of several parameters were also investigated, including initial dye concentration, nanophotocatalyst concentration, CQD content, initial pH of the dye solution, and reaction kinetics. Degradation study data follow the first-order reaction rate (R2 > 0.93). Finally, a simple and low-cost synthesis approach, rapid degradation, and outstanding stability of the CQD-coated CZF nanophotocatalyst should make it a potential photocatalyst for dye wastewater treatment.
RESUMEN
In contemplation of treating hazardous industrial wastewater, sodium tripolyphosphate (TPP) and vanillin (V)-modified chitosan-based magnetic nano-sorbents (TPP-CMN and V-CMN) were prepared, and the physical and surface properties of both nano-sorbents were characterised. The results of FE-SEM and XRD showed an average size of between 6.50 and 17.61 nm for Fe3O4 magnetic nanoparticles. The Physical Property Measurement System (PPMS) was carried out, and the saturation magnetisations for chitosan, Fe3O4 nanoparticles, TPP-CMN, and V-CMN were 0.153, 67.844, 7.211, and 7.772 emu.g-1, respectively. By using multi-point analysis, the BET surface areas of the synthesised TPP-CMN and V-CMN nano-sorbents were found to be 8.75 and 6.96 m2/g, respectively. The synthesised TPP-CMN and V-CMN were investigated as effective nano-sorbents to uptake Cd (II), Co (II), Cu (II), and Pb (II) ions, and the results were investigated by AAS. The adsorption process of heavy metals was investigated by the batch equilibrium technique, and the sorption capacity values of Cd (II), Co (II), Cu (II), and Pb (II) ions by TPP-CMN were 91.75, 93.00, 87.25, and 99.96 mg/g. By V-CMN, the values were 92.5, 94.00, 88.75, and 99.89 mg/g, respectively. The equilibrium times for adsorption were found to be 15 minutes for TPP-CMN and 30 minutes for V-CMN nano-sorbents. The adsorption isotherms, kinetics, and thermodynamics were studied to understand the adsorption mechanism. Furthermore, the adsorption of two synthetic dyes and two real wastewater samples was studied and obtained significant results. These nano-sorbents' simple synthesis, high sorption capability, excellent stability, and recyclability may provide highly efficient and cost-effective nano-sorbents for wastewater treatment.
RESUMEN
Fabrication and development of effective visible-light-responsive photocatalysts are required to tackle critical environmental issues. The aim of this study was to develop a nanocomposite material with improved photocatalytic activity for the degradation of industrial dyes such as Reactive Orange-16 (RO-16), Reactive Blue (RB-222), Reactive Yellow-145 (RY-145), and Disperse Red-1 (DR-1) without the need for a post-separation process after use. Here we report the hydrothermal synthesis of nanodots of Co1-xZnxFe2O4 (x = 0.3, 0.5 and 0.7), coated with polyaniline, by in situ polymerization. The Co1-xZnxFe2O4 nanodots, coated with polyaniline (PANI) nanograins, facilitated optical properties by easily capturing visible light. X-ray Diffraction (XRD) patterns and Scanning Electron Microscopy (SEM) images have confirmed the single-phase spinel structure of Co1-xZnxFe2O4 nanodot and nano-pore size of the Co1-xZnxFe2O4/PANI nanophotocatalyst. The specific surface area of the Brunauer-Emmett-Teller (BET) of the Co1-xZnxFe2O4/PANI photocatalyst was determined to be 24.50 m2/g by multipoint analysis. The final Co1-xZnxFe2O4/PANI (x = 0.5) nanophotocatalyst showed high efficiency in the catalytic degradation of toxic dyes (â¼98% within 5 min), with good mechanical stability and recyclability under visible light irradiation. The nanophotocatalyst was re-used and its efficiency was largely maintained, even after seven cycles (â¼82%) of degradation. The effects of various parameters, such as initial dye concentration, nanophotocatalyst concentration, initial pH of dye solution, and reaction kinetics were studied. According to the Pseudo-first-order kinetic model, photodegradation data followed the first-order reaction rate (R2 > 0.95) of degradation of dyes. In conclusion, a simple and low-cost synthesis process, speedy degradation and excellent stability of polyaniline-coated Co1-xZnxFe2O4 nanophotocatalyst could be used as a promising photocatalyst for dye-wastewater treatment.