RESUMEN
We investigated the influence of the photobleaching (PB) effect on the dosimetry performances of a phosphosilicate single-mode optical fiber (core diameter of 6.6 µm) operated at 638 nm, within the framework of the LUMINA project. Different irradiation tests were performed under ~40 keV mean energy fluence X-rays at a 530 µ Gy(SiO2)/s dose rate to measure in situ the radiation-induced attenuation (RIA) growth and decay kinetics while injecting a 638 nm laser diode source with powers varying from 500 nW to 1 mW. For injected continuous power values under 1 µW, we did not measure any relevant influence of the photobleaching effect on the fiber radiation sensitivity coefficient of ~140 dB km-1 Gy-1 up to ~30 Gy. Above 1 µW, the fiber radiation sensitivity is significantly reduced due to the PB associated with the signal and can decrease to ~80 dB km-1 Gy-1 at 1 mW, strongly affecting the capability of this fiber to serve as a dosimeter-sensitive element. Higher power values up to 50 µW can still be used by properly choosing a pulsed regime with periodic injection cycles to reduce the PB efficiency and maintain the dosimetry properties. Basing on the acquired data, a simple model of the photobleaching effect on a coil of the investigated fiber is proposed in order to estimate its sensitivity coefficient evolution as a function of the cumulated dose and its fiber length when injecting a certain laser power. Additional studies need to investigate the influence of the temperature and the dose rate on the PB effects since these parameters were fixed during all the reported acquisitions.
RESUMEN
The optical-fiber-based dosimeter of the LUMINA project was deployed in August 2021 in the International Space Station in the framework of the Alpha mission. The sensing elements of the dosimeter are P-doped optical fibers, which were proven to be excellent candidates for dosimetry applications. The twofold objective of this paper is to provide a theoretical model for the radiation response of the dosimeter and to report on the experimental work carried out at CERN for the qualification and calibration of the engineering model of the LUMINA dosimeter. Combining the theoretical response and experimental data, the calibration curve of the flight model is obtained. Finally, this study broadens the investigation of the room temperature radiation response of P-doped optical fibers in a range of dose rates 104 times lower than previously reported, from 21µGy(SiO2)/h to145mGy(SiO2)/h.
RESUMEN
The potential of fiber-based sensors to monitor the fluence of atmospheric neutrons is evaluated through accelerated tests at the TRIUMF Neutron Facility (TNF) (BC, Canada), offering a flux approximatively 109 higher than the reference spectrum observed under standard conditions in New York City, USA. The radiation-induced attenuation (RIA) at 1625 nm of a phosphorus-doped radiation sensitive optical fiber is shown to linearly increase with neutron fluence, allowing an in situ and easy monitoring of the neutron flux and fluence at this facility. Furthermore, our experiments show that the fiber response remains sensitive to the ionization processes, at least up to a fluence of 7.1 × 1011 n cm-², as its radiation sensitivity coefficient (~3.36 dB km-1 Gy-1) under neutron exposure remains very similar to the one measured under X-rays (~3.8 dB km-1 Gy-1) at the same wavelength. The presented results open the way to the development of a point-like or even a distributed dosimeter for natural or man-made neutron-rich environments. The feasibility to measure the dose caused by the neutron exposure during stratospheric balloon experiments, or during outer space missions, is presented as a case study of a potential future application.
RESUMEN
This paper review presents Single Event Effects (SEE) irradiation tests under heavy ions of the test-chip of D-Flip-Flop (DFF) cells and complete readout integrated circuits (ROIC) as a function of temperature, down to 50 K. The analyses of the experimental data are completed using the SEE prediction tool MUSCA SEP3. The conclusions derived from the experimental measurements and related analyses allow to update the current SEE radiation hardness assurance (RHA) for readout integrated circuits of infrared image sensors used at cryogenic temperatures. The current RHA update is performed on SEE irradiation tests at room temperature, as opposed to the operational cryogenic temperature. These tests include SET (Single Event Transient), SEU (Single Event Upset) and SEFI (Single Event Functional Interrupt) irradiation tests. This update allows for reducing the cost of ROIC qualifications and the test setup complexity for each space mission.