RESUMEN
A surface plasmon resonance imaging (SPRI)-based biosensor is demonstrated for the detection of both hydrogen peroxide (H2O2) and glucose. The H2O2 to be detected acts as an oxidant and etch the silver film. This process gradually effects on resonance condition and consequently the reflected light intensity at a fixed angle. The etching rate of the silver film shows a clear relation with the H2O2 concentration. Therefore, monitoring the reflected light intensity progressively changing over a few minutes, enables accurate detection of H2O2 concentrations ranging from 0 to 200 µM (within physiological range of 0.25-50 µM), with a remarkable limit of detection (LOD) as low as 40 nM. In this regard, the behavior of the surface plasmon resonance (SPR) dip in response to the reduction of the silver film thickness is predicted by Winspall simulation software. These simulation results are in good agreement with the experimental results. Moreover, the proposed method can be applied to determine glucose concentrations ranging from 0 to 10 mM, encompassing the physiological range of 3-8 mM. This is achieved by observing the generated H2O2 through the enzymatic oxidation reaction between glucose and glucose oxidase (Gox). The sensor demonstrates remarkable sensitivity and selectivity, with a detection limit as low as 175 µM for glucose concentration. Furthermore, accurate measurement of glucose concentration in an actual human serum sample is achievable with the proposed sensor, using the standard addition method. The suggested glucose sensor shows promising prospects for use in routine glucose testing, employing a label-free, real-time, and multiplex detection approach.© 2017 Elsevier Inc. All rights reserved.
Asunto(s)
Peróxido de Hidrógeno , Plata , Resonancia por Plasmón de Superficie , Resonancia por Plasmón de Superficie/métodos , Peróxido de Hidrógeno/química , Peróxido de Hidrógeno/análisis , Plata/química , Humanos , Glucosa Oxidasa/química , Glucosa Oxidasa/metabolismo , Técnicas Biosensibles/métodos , Límite de Detección , Glucosa/análisis , Glucemia/análisisRESUMEN
Photothermal effect in plasmonic nanostructures (thermoplasmonic), as a nanoscale heater, has been widely used in biomedical technology and optoelectronic devices. However, the big challenge in this effect is the quantitative characterization of the delivered heat to the surrounding environment. In this work, a plasmonic metasurface (as a nanoheater), and a Fabry-Perot (FP) cavity including liquid crystal (as a thermometer element) are integrated. The metasurface is manufactured through a bottom-up deposition method and has a near perfect absorption that causes an efficient temperature rising in the photothermal experiment under a low intensity of irradiation ($0.25\; {\rm W}/{{\rm cm}^2}$0.25W/cm2). Generated heat from the metasurface dissipates to the liquid crystal (LC) layer and makes a spectral shift of FP modes. More than 50°C temperature elevation with accuracy of 1.3°C are measured based on the consistency of anisotropic thermo-tropic data of the LC and a spectral shift of FP modes. The calculated figure of merit (FoM) of the constructed device, which indicates the temperature sensitivity, is 22. The FoM is four times more than other reported thermometry devices with broad spectral width. The device can be also used as an all-optical device to control the plasmonic resonance spectrum.
RESUMEN
Active plasmonics combined with liquid crystal (LC) has found many applications in nanophotonics. In this Letter, we propose a fast response active plasmonic device based on the interplay of the plasmonic spectrum and Fabry-Perot (FP) modes. The plasmonic spectrum and FP modes are excited in a layer of gold nanoparticle (NP) islands and an LC microcavity, respectively. The FP mode splits the extinction spectrum of the NP to narrow bands, which are named hybrid modes (HMs). Due to multiple reflections of photons inside the cavity, the extinction coefficient is enhanced compared to a bare NP layer. An external electric field shifts the HM leading to a significant increase in the figure of merit (FoM) related to the activation ability by up to a factor of 45. Additionally, we could reduce the response time of active plasmonics. This decrease in response time is achieved through polymer-dispersed LC (PDLC) in the microcavity. Utilizing a mesogenic monomer in PDLC reduces the response time of the HM into the microsecond range, while the sample remains transparent.