RESUMEN
Herein is presented a simple and sensible method to determine organic pollutants in water, based on the utilization of silver nanoparticles (AgNPs) loaded in Polyacrylamide (PAAm)/starch hybrid hydrogels combined with surface-enhanced Raman scattering (SERS) spectroscopy. The materials were characterized by swelling degree studies, UV-Visible spectroscopy (UV-Vis), X-ray diffraction (XRD) and scanning electron microscopy (SEM). PAAm/starch hydrogels showed variable swelling capacity, according to the synthetic molar composition. The most promising results were attributed to lower concentrations of starch and crosslink agent (N,N'-methylenebisacrylamide - MBA). Spectroscopic analysis confirmed the formation of AgNPs, by noticing the peak at around 420 nm, due to its surface plasmon resonance (SPR) effect. The results showed that AgNPs were stabilized by hydrogels networks. The average size of the AgNPs was smaller than 100 nm and the size and quantity of nanoparticles were influenced by the molar composition of the hydrogel matrix. The SERS substrate based on the AgNPs-PAAm/starch exhibited reproducibility, stability, and limit of detection (LOD) of phenol in water of 1 × 10-8 M. The average mass of AgNPs-PAAm/starch hydrogels used for each detection analysis was around 10 mg. The spectra with enhanced intensities were possible due to a large number of hot spots generated on the AgNPs-PAAm/starch hydrogel substrate, which leads to potential use for organic pollutant detection. In addition, there is also the possibility of reusing the hydrogel matrix substrate in other analyzes.
Asunto(s)
Monitoreo del Ambiente/métodos , Hidrogeles/química , Nanopartículas del Metal/química , Fenoles/análisis , Plata/química , Contaminantes Químicos del Agua/análisis , Resinas Acrílicas/química , Monitoreo del Ambiente/instrumentación , Límite de Detección , Microscopía Electrónica de Rastreo , Reproducibilidad de los Resultados , Espectrometría Raman , Almidón/química , Resonancia por Plasmón de Superficie , Agua , Difracción de Rayos XRESUMEN
In this study, we intended to evaluate the performance of olefin-based drilling fluids after addition of cellulose nanocrystal (CNC) derivatives. For this purpose, firstly, cellulose nanocrystals, produced from sulfuric acid hydrolysis of cotton fibers, were functionalized with poly(N-isopropylacrylamide) (PNIPAM) chains via free radicals. The samples were then characterized via Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), confocal microscopy, dynamic light scattering (DLS), and zeta potential measurements in water. The FTIR and NMR spectra exhibited the characteristic signals of CNC and PNIPAM groups, indicating successful grafting. As expected, X-ray diffractograms showed that the crystallinity of CNCs reduces after chemical modification. TGA revealed that the surface-functionalized CNCs present higher thermal stability than pure CNCs. The confocal microscopy, zeta potential, and DLS results were consistent with the behavior of cellulose nanocrystals decorated by a shell of PNIPAM chains. The fluids with a small amount of modified CNCs presented a much lower volume of filtrate after high-temperature and high-pressure (HTHP) filtration tests than the corresponding standard fluid, indicating the applicability of the environmentally friendly particles for olefin-based drilling fluids.
Asunto(s)
Resinas Acrílicas/química , Alquenos/química , Celulosa/química , Nanopartículas/química , Polímeros/química , Agua/química , Hidrólisis , TemperaturaRESUMEN
Biodegradability and ecotoxicity of products used in oil industry are of great relevance and corrosion inhibitor could not be an exception. In earlier reports, chitosan and some derivatives were evaluated as corrosion inhibitors at acid pH, mainly due to polymer solubility. An eco-friendly corrosion inhibitor with water solubility in all pH range should be ideal, as well as that could act under the high salinity of oil field environment. Thus, herein is presented the performance of a water-soluble carboxymethylchitosan (CMC) as corrosion inhibitor in presence of chlorides (3.5% NaCl) in 1020 carbon steel, without any addition of acid or base. CMC showed good properties as corrosion inhibitor in media containing Cl-, and behaved as an anodic inhibitor. CMC exhibited inhibitory efficiency of about 80% and 67%, according to Tafel curve and electrochemical impedance, respectively, which was attributed to chemisorption mechanism (ΔGads ≈ -45 kJ/mol).