RESUMEN

A new thermoplastic polymer for orthodontic applications was obtained and extruded into wires with round and rectangular cross sections. We evaluated the potential of new aesthetic archwire: tensile, three point bending, friction and stress relaxation behaviour, and formability characteristics were assessed. Stresses delivered were generally slightly lower than typical beta-titanium and nickel-titanium archwires. The polymer wire has good instantaneous mechanical properties; tensile stress decayed about 2% over 2h depending on the initial stress relaxation for up to 120h. High formability allowed shape bending similar to that associated with stainless steel wires. The friction coefficients were lower than the metallic conventional archwires improving the slipping with the brackets. This new polymer could be a good candidate for aesthetic orthodontic archwires.

Asunto(s)

RESUMEN

OBJECTIVE: This study focuses on the fatigue behavior of titanium dental implants as-received, with a grit-blasted surface and with a new bioactive surface treatment (2Steps). BACKGROUND: The 2Step process consists of (1) an initial grit-blasting process to produce a micro-rough surface, followed by (2) a combined thermo-chemical treatment that produces a potentially bioactive surface, that is, that can form an apatitic layer when exposed to biomimetic conditions in vitro. The 2Step treatment produced micro-rough and apatitic coating implants. METHODS: Residual stresses were determined by means of X-ray diffraction. The fatigue tests were carried out at 37°C on 500 dental implants, and the S-N curve was determined. The fatigue-crack nucleation for the different treatments was analyzed. RESULTS: The fatigue tests show that the grit-blasting process improves the fatigue life. This is a consequence of the layer of compressive residual stresses that the treatment generates in titanium surfaces. Dental implants that had its surfaced prepared with the 2Step procedure (grit-blasting and thermo-chemical treatment) had its fatigue life decreased by 10% due to the incorporation of oxygen to the surface and the relaxation of the compressive residual stress produced by the heat treatment. CONCLUSIONS: Thermo-chemical treatment is an excellent compromise between the improvement of bioactive and mechanical long-life behaviors.

Asunto(s)

RESUMEN

The anatomy of dental compensation curve in the frontal plane described by George H. Wilson is one of the occlusal determinants of orthodontic treatment. However, there is few published comparing malocclusion and normocclusion individuals. Objectives: The aim of this study is to compare the curve of Wilson at first and second maxillary molars, normocclusion pattern and malocclusion pattern, with and without bilateral posterior crossbite, using angular references in CBCT studies. Material and Methods: We analyzed 10 cases of malocclusion with bilateral posterior crossbite, 10 cases of malocclusion without bilateral posterior crossbite and 10 cases with non orthodontic normocclusion (patients who underwent cone beam study for other reasons than orthodontic). All of them were adults, more than 19 years. Angular variables from left and right axis (line connecting the occlusal and furcation groove) of first and second molars towards a perpendicular to the frontal palate were measured. There was carried out an Anova test, Bonferroni analysis and Levene´s statistics. Results: The descriptive analysis of the results shows an average values of total maxillary curve of Wilson for first molars (sum of left and right angle) of 8.1° for normocclusion group, 0.4° for the malocclusion pattern with bilateral posterior crossbite and 16.9° for the malocclusion pattern without this alteration. The mean differences was statistical significant (P<0,042) between between malocclusion pattern groups with and without crossbite .Conclusion: The curve of Wilson, measured at maxillary first molars in patients with bilateral posterior crossbiteis more concave than the other groups, suggesting no dentoalveolar compensations (AU)

Asunto(s)

RESUMEN

UNLABELLED: The anatomy of dental compensation curve in the frontal plane described by George H. Wilson is one of the occlusal determinants of orthodontic treatment. However, there is few published comparing malocclusion and normocclusion individuals. OBJECTIVES: The aim of this study is to compare the curve of Wilson at first and second maxillary molars, normocclusion pattern and malocclusion pattern, with and without bilateral posterior crossbite, using angular references in CBCT studies. MATERIAL AND METHODS: We analyzed 10 cases of malocclusion with bilateral posterior crossbite, 10 cases of malocclusion without bilateral posterior crossbite and 10 cases with non orthodontic normocclusion (patients who underwent cone beam study for other reasons than orthodontic). All of them were adults, more than 19 years. Angular variables from left and right axis (line connecting the occlusal and furcation groove) of first and second molars towards a perpendicular to the frontal palate were measured. There was carried out an Anova test, Bonferroni analysis and Levene's statistics. RESULTS: The descriptive analysis of the results shows an average values of total maxillary curve of Wilson for first molars (sum of left and right angle) of 8.1° for normocclusion group, 0.4° for the malocclusion pattern with bilateral posterior crossbite and 16.9° for the malocclusion pattern without this alteration. The mean differences was statistical significant (P<0,042) between between malocclusion pattern groups with and without crossbite . CONCLUSION: The curve of Wilson, measured at maxillary first molars in patients with bilateral posterior crossbite is more concave than the other groups, suggesting no dentoalveolar compensations.

Asunto(s)

RESUMEN

Objectives: Cone Beam Computerized Tomography (CBCT) allows the possibility of modifying some of thediagnostic tools used in orthodontics, such as cephalometry. The first step must be to study the characteristics ofthese devices in terms of accuracy and reliability of the most commonly used landmarks. The aims were 1- Toassess intra and inter-observer reliability in the location of anatomical landmarks belonging to hard tissues of theskull in images taken with a CBCT device, 2- To determine which of those landmarks are more vs. less reliableand 3- To introduce planes of reference so as to create cephalometric analyses appropriated to the 3D reality.Study design: Fifteen patients who had a CBCT (i-CAT®) as a diagnostic register were selected. To assess thereproducibility on landmark location and the differences in the measurements of two observers at different times,41 landmarks were defined on the three spatial axes (X,Y,Z) and located. 3.690 measurements were taken and, aseach determination has 3 coordinates, 11.070 data were processed with SPSS® statistical package. To discover thereproducibility of the method on landmark location, an ANOVA was undertaken using two variation factors: time(t1, t2 and t3) and observer (Ob1 and Ob2) for each axis (X, Y and Z) and landmark. The order of the CBCT scanssubmitted to the observers (Ob1, Ob2) at t1, t2, and t3, were different and randomly allocated. Multiple comparisons were undertaken using the Bonferroni test. The intra- and inter-examiner ICC's were calculated. Results: Intra- and inter-examiner reliability was high, both being ICC ≥ 0.99, with the best frequency on axis Z. Conclusions: The most reliable landmarks were: Nasion, Sella, Basion, left Porion, point A, anterior nasal spine, Pogonion, Gnathion, Menton, frontozygomatic sutures, first lower molars and upper and lower incisors. Those with less reliability were the supraorbitals, right zygion and posterior nasal spine (AU)

Asunto(s)

RESUMEN

Aims: To evaluate the reliability and reproducibility of calculating the Bolton Index using cone-beam computed tomography (CBCT), and to compare this with measurements obtained using the 2D Digital Method. Material and Methods: Traditional study models were obtained from 50 patients, which were then digitized in order to be able to measure them using the Digital Method. Likewise, CBCTs of those same patients were undertaken using the Dental Picasso Master 3D® and the images obtained were then analysed using the InVivoDental programme. Results: By determining the regression lines for both measurement methods, as well as the difference between both of their values, the two methods are shown to be comparable, despite the fact that the measurements analysed presented statistically significant differences. Conclusions: The three-dimensional models obtained from the CBCT are as accurate and reproducible as the digital models obtained from the plaster study casts for calculating the Bolton Index. The differences existing between both methods were clinically acceptable (AU)

Asunto(s)

RESUMEN

AIMS: To evaluate the reliability and reproducibility of calculating the Bolton Index using cone-beam computed tomography (CBCT), and to compare this with measurements obtained using the 2D Digital Method. MATERIAL AND METHODS: Traditional study models were obtained from 50 patients, which were then digitized in order to be able to measure them using the Digital Method. Likewise, CBCTs of those same patients were undertaken using the Dental Picasso Master 3D® and the images obtained were then analysed using the InVivoDental programme. RESULTS: By determining the regression lines for both measurement methods, as well as the difference between both of their values, the two methods are shown to be comparable, despite the fact that the measurements analysed presented statistically significant differences. CONCLUSIONS: The three-dimensional models obtained from the CBCT are as accurate and reproducible as the digital models obtained from the plaster study casts for calculating the Bolton Index. The differences existing between both methods were clinically acceptable.

Asunto(s)

RESUMEN

OBJECTIVES: Cone Beam Computerized Tomography (CBCT) allows the possibility of modifying some of the diagnostic tools used in orthodontics, such as cephalometry. The first step must be to study the characteristics of these devices in terms of accuracy and reliability of the most commonly used landmarks. The aims were 1- To assess intra and inter-observer reliability in the location of anatomical landmarks belonging to hard tissues of the skull in images taken with a CBCT device, 2- To determine which of those landmarks are more vs. less reliable and 3- To introduce planes of reference so as to create cephalometric analyses appropriated to the 3D reality. STUDY DESIGN: Fifteen patients who had a CBCT (i-CAT) as a diagnostic register were selected. To assess the reproducibility on landmark location and the differences in the measurements of two observers at different times, 41 landmarks were defined on the three spatial axes (X,Y,Z) and located. 3.690 measurements were taken and, as each determination has 3 coordinates, 11.070 data were processed with SPSS statistical package. To discover the reproducibility of the method on landmark location, an ANOVA was undertaken using two variation factors: time (t1, t2 and t3) and observer (Ob1 and Ob2) for each axis (X, Y and Z) and landmark. The order of the CBCT scans submitted to the observers (Ob1, Ob2) at t1, t2, and t3, were different and randomly allocated. Multiple comparisons were undertaken using the Bonferroni test. The intra- and inter-examiner ICC's were calculated. RESULTS: Intra- and interexaminer reliability was high, both being ICC ≥ 0.99, with the best frequency on axis Z. CONCLUSIONS: The most reliable landmarks were: Nasion, Sella, Basion, left Porion, point A, anterior nasal spine, Pogonion, Gnathion, Menton, frontozygomatic sutures, first lower molars and upper and lower incisors. Those with less reliability were the supraorbitals, right zygion and posterior nasal spine.

Asunto(s)

RESUMEN

PURPOSE: This study sought to determine whether the mechanical properties of titanium dental implants changed after exposure to bacteria. MATERIALS AND METHODS: Two strains of bacteria (Streptococcus sanguinis and Lactobacillus salivarius) were used in the study. The adhesive properties of the two strains were investigated as follows. Titanium implants were placed in bacteria broth, seeded with the two bacteria strains, and left in the broth for 1 or 3 months. Another group of titanium implants was immersed in artificial saliva at 37°C for 3 months. Ten implants in each group were tested in 37°C artificial saliva to evaluate their mechanical flexural strength and fatigue life. RESULTS: The bacterial cultures grew quickly on titanium surfaces. After 1 month of bacteria culture in vitro, the bacteria had produced corrosion pits on the titanium surfaces. After 3 months of bacterial culture, a 7% decrease in the flexural strength of the implant samples and a decrease of 15% in the number of cycles to failure by fatigue were seen versus implants not exposed to bacteria. CONCLUSIONS: These results demonstrate that, in physiologic conditions in vitro, bacteria have the capacity to produce a pitting corrosion phenomenon on exposed titanium surfaces, leading to a significant deterioration in the mechanical properties of the implant. It is therefore logical to conclude that bacteria may produce corrosion that reduces the useful life of dental implants.

Asunto(s)

RESUMEN

The mandibular third molar (3M) is the tooth that is most often impacted, with lack of space being one of the reasons. In some orthodontic treatments, premolars are extracted in order to create space. The aims of our study are: firstly, to assess the changes in the angulation and position of the 3M in cases treated either with or without extraction of the first or second premolars; secondly, to analyse the variation in the gonial angle and the degree of inclusion of the 3M; and lastly, to establish a predictive impaction model for 3M. This study included 88 patients:28 patients treated with extractions of first premolars, 30 with second premolars and 30 without.The initial and final orthopantomography was analysed and the angulation of the 3M was measured, a new variable being created to determine the degree of 3M inclusion in the mandibular ramus. The results show that the angulation of 3M improves with time, regardless of treatment, and presents a greater disinclusion in cases treated with extractions. The gonial angle tends to diminish with age in all cases. The conclusions suggest that other factors may influence the angulation and position of 3M and that it is not possible to establish a predictive impaction model (AU)

No disponible

Asunto(s)

RESUMEN

The mandibular third molar (3M) is the tooth that is most often impacted, with lack of space being one of the reasons. In some orthodontic treatments, premolars are extracted in order to create space. The aims of our study are: firstly, to assess the changes in the angulation and position of the 3M in cases treated either with or without extraction of the first or second premolars; secondly, to analyse the variation in the gonial angle and the degree of inclusion of the 3M; and lastly, to establish a predictive impaction model for 3M. This study included 88 patients: 28 patients treated with extractions of first premolars, 30 with second premolars and 30 without. The initial and final orthopantomography was analysed and the angulation of the 3M was measured, a new variable being created to determine the degree of 3M inclusion in the mandibular ramus. The results show that the angulation of 3M improves with time, regardless of treatment, and presents a greater disinclusion in cases treated with extractions. The gonial angle tends to diminish with age in all cases. The conclusions suggest that other factors may influence the angulation and position of 3M and that it is not possible to establish a predictive impaction model.

Asunto(s)