RESUMEN
Exposure to bioaerosols can pose a health risk to workers at wastewater treatment plants (WWTPs) and to habitants of their surroundings. The main objective of this study was to examine the presence of harmful microorganisms in the air emission from a new type of hospital WWTP employing advanced wastewater treatment technologies. Air particle measurements and sampling of inhalable bacteria, endotoxin and noroviruses (NoVs) were performed indoor at the WWTP and outside at the WWTP ventilation air exhaust, downwind of the air exhaust, and upwind of the WWTP. No significant differences were seen in particle and endotoxin concentrations between locations. Bacterial concentrations were comparable or significantly lower in the exhaust air than inside the WWTP and in the upwind reference. Bacterial isolates were identified using matrix-assisted laser desorption-ionization time-of-flight mass spectrometry. In total, 35 different bacterial genera and 64 bacterial species were identified in the air samples. Significantly higher genus and species richness was found with an Andersen Cascade Impactor compared with filter-based sampling. No pathogenic bacteria were found in the exhaust air. Streptomyces was the only bacterium found in the air both inside the WWTP and at the air emission, but not in the upwind reference. NoV genomes were detected in the air inside the WWTP and at the air exhaust, albeit in low concentrations. As only traces of NoV genomes could be detected in the exhaust air they are unlikely to pose a health risk to surroundings. Hence, we assess the risk of airborne exposure to pathogenic bacteria and NoVs from the WWTP air emission to surroundings to be negligible. However, as a slightly higher NoV concentration was detected inside the WWTP, we cannot exclude the possibility that exposure to airborne NoVs can pose a health risk to susceptible to workers inside the WWTP, although the risk may be low.
Asunto(s)
Microbiología del Aire , Aguas Residuales/microbiología , Bacterias/aislamiento & purificación , Norovirus , Emisiones de VehículosRESUMEN
A Near Field/Far Field (NF/FF) model is a well-accepted tool for precautionary exposure assessment but its capability to estimate particulate matter (PM) concentrations is not well studied. The main concern is related to emission source characterization which is not as well defined for PM emitters compared to e.g. for solvents. One way to characterize PM emission source strength is by using the material dustiness index which is scaled to correspond to industrial use by using modifying factors, such as handling energy factors. In this study we investigate how well the NF/FF model predicts PM concentration levels in a paint factory. PM concentration levels were measured during big bag and small bag powder pouring. Rotating drum dustiness indices were determined for the specific powders used and applied in the NF/FF model to predict mass concentrations. Modeled process specific concentration levels were adjusted to be similar to the measured concentration levels by adjusting the handling energy factor. The handling energy factors were found to vary considerably depending on the material and process even-though they have the same values as modifying factors in the exposure models. This suggests that the PM source characteristics and process-specific handling energies should be studied in more detail to improve the model-based exposure assessment.
Asunto(s)
Contaminantes Atmosféricos/análisis , Contaminación del Aire/estadística & datos numéricos , Monitoreo del Ambiente , Residuos Industriales/análisis , Modelos Químicos , Material Particulado/análisis , PinturaRESUMEN
CONTEXT: Titanium dioxide (TiO2) factory workers' source specific exposure and dose to airborne particles was studied extensively for particles between 5 nm and 10 µm in size. OBJECTIVE: We defined TiO2 industry workers' quantitative inhalation exposure levels during the packing of pigment TiO2 (pTiO2) and nanoscale TiO2 (nTiO2) material from concentrations measured at work area. METHODS: Particle emissions from different work events were identified by linking work activity with the measured number size distributions and mass concentrations of particles. A lung deposit model was used to calculate regional inhalation dose rates in units of particles min⻹ and µg min⻹ without use of respirators. RESULTS: Workers' average exposure varied from 225 to 700 µg m⻳ and from 1.15 × 104 to 20.1 × 104 cmâ»4. Over 90% of the particles were smaller than 100 nm. These were mainly soot and particles formed from process chemicals. Mass concentration originated primarily from the packing of pTiO2 and nTiO2 agglomerates. The nTiO2 exposure resulted in a calculated dose rate of 3.6 × 106 min⻹ and 32 µg min⻹ where 70% of the particles and 85% of the mass was deposited in head airways. CONCLUSIONS: The recommended TiO2 exposure limits in mass by NIOSH and in particle number by IFA were not exceeded. We recommend source-specific exposure assessment in order to evaluate the workers' risks. In nTiO2 packing, mass concentration best describes the workers' exposure to nTiO2 agglomerates. Minute dose rates enable the simulation of workers' risks in different exposure scenarios.