RESUMEN

A vector hydrophone is an underwater acoustic sensor that can detect the direction of a sound source. Wide-band characteristics and high sensitivity enhance the performance of underwater surveillance systems in complex environments. A vector hydrophone comprising a triaxial piezoelectric accelerometer and spherical hydrophone was fabricated and tested in the air and underwater. The vector hydrophone was designed to exceed the quantitative figures of merit (i.e., receiving voltage sensitivity and bandwidth) of commercially available hydrophones. Accelerometer performance was enhanced by placing a pair of piezoelectric single crystals on each axis and modifying the seismic mass material. The receiving voltage sensitivity of the omnidirectional hydrophone was approximately −160 dB relative to 1 V/µPa with the amplifier in water; the sensitivity of the accelerometer exceeded 300 mV/g in air and −215 dB relative to 1 V/µPa underwater over the frequency range of interest. The receiving directivity of the vector hydrophone was validated underwater, which confirmed that it could detect the direction of a sound source.

Asunto(s)

RESUMEN

A cymbal transducer has a simple structure consisting of a piezoceramic disk and metallic caps and has broadband characteristics when built as an array. The finite element method (FEM) is generally used to analyze the characteristics of acoustic transducers. However, the FEM requires a longer analysis time as the model becomes larger, which makes it limited and less efficient for analyzing the cymbal array. In this study, a new equivalent circuit with higher efficiency and accuracy, comparable to that of the FEM, was proposed to analyze the performance of cymbal arrays. The equivalent circuit for the array was constructed by connecting the equivalent circuits of individual cymbal transducers in parallel with a radiation impedance matrix that included both the self- and mutual radiation characteristics of the array. The validity of the new equivalent circuit was verified by measuring the transmitting voltage response of a cymbal array specimen and comparing it with that calculated using the circuit. The comparison confirmed the efficiency of the equivalent circuit in analyzing the characteristics of the cymbal array. The proposed equivalent circuit can facilitate the design of a large array of cymbal transducers.

Asunto(s)

RESUMEN

Cymbal transducers are frequently used as an array rather than a single element because of their high quality factor and low energy conversion efficiency. When used as an array, cymbal transducers are likely to have a big change in their frequency characteristics due to the interaction with neighboring elements. In this study, we designed an array pattern of cymbal transducers to achieve a wide frequency bandwidth using this property. First, cymbal transducers with specific center frequencies were designed. Next, a 2 × 2 planar array was constructed with the designed transducers, where dielectric polarity directions of the transducers were divided into two cases (i.e., same and different). For the array, the effect of the difference in the center frequencies and the spacing between the transducers on the acoustic characteristics of the entire array was analyzed. Based on the results, the structural pattern of the array was optimized to have the maximum fractional bandwidth while maintaining the transmitting voltage response over a given requirement. The design validity was verified by making cymbal array prototypes, followed by measuring their performances and comparing them with that of the design.

Asunto(s)

RESUMEN

Realization of flexible electronics is an attractive challenge because of its great potential in many applications. However, the design of flexible and highly conductive metal electrodes has been a bottleneck for the fabrication of flexible devices because bulk metals are easily fractured when subjected to elongation or compression. Here, we demonstrate metal-ceramic nanolaminates as electrodes for flexible electronic devices. Insertion of ceramic layers, each with a thickness of a few nanometers, into an otherwise metal electrode significantly improved its strength and bending stability and only slightly reduced its electrical conductivity. Finally, we demonstrated that a touch screen panel fabricated with metal-ceramic nanolaminate electrodes was stable to 200 000 cycles of folding to a bending radius of 3 mm.

RESUMEN

This paper describes the results of range-dependent geoacoustic inversion using vertical line array data obtained from the 4th Matched Acoustic Properties and Localization Experiment conducted in the East Sea of Korea. The narrowband multitone continuous-wave signal from the towed source was analyzed to estimate the range-dependent geoacoustic properties along the radial track. The primary approach is based on the sectorwise inversion scheme. The inversion region up to 7.5 km from the vertical line array was divided into several segments, and the subinversions for each segment were performed sequentially. To reduce the dominance of low-angle arrivals, which bears little information for the bottom segment in question, matched beam processing with beam filtering was used for the cost function. The performance of proposed algorithm was tested using simulated data for an environment representative of the experimental site. The inversion results for the experimental data were consistent with the geophysical database and were validated from matched-field source localization using frequencies different from those used in the inversion.

Asunto(s)

RESUMEN

The effect of temperature on polyvinylchloride (PVC) combustion using a downstream tubular furnace was investigated for the formation of polycylcic aromatic hydrocarbons (PAHs) and chlorinated compounds. As the temperature increased, higher levels of PAHs were generated. Chlorinated compounds reached a peak at 600 degrees C, with low emissions recorded at 300 and 900 degrees C. There was a close correlation (R2 = 0.97) among polychlorinated biphenyls (PCBs), hexachlorobenzene, pentachlorobenzene, and polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs). PAHs at all temperatures were analyzed in the gas phase. PCDD/Fs and PCBs were emitted as a solid phase at 300 and 600 degrees C and as a gas phase at 900 degrees C. For some PAHs, chlorobenzenes, and PCDD/Fs, a mathematical equation between the gas and solid phase and the reciprocal temperature in semilog proportion was derived. The proposed equation, which is log (amount in gas phase/amount in solid phase) = -A/T + B, where T is the temperature of the furnace and A and B are constants, for these species relating their gas/solid distributions showed a good relationship.

Asunto(s)

RESUMEN

Emission characteristics of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in diesel engine were studied with variable load rate of the diesel engine with the emission test cycles, US D-13 mode. The load rate is changed from 25% to 50% and 75% at constant speed of 2400 rpm. PCDD/Fs concentration and phase distribution of PCDD/Fs with the isokinetic sampling of exhaust gas is obtained in this study. The average PCDD/Fs concentrations per unit of exhaust gas with 25%, 50% and 75% load rate are 14.5, 6.9 and 6.4 pg-TEQ/N m3, respectively. In all diesel engine runs, PCDFs are more prevalent than PCDDs. As a load rate is increased, the ratio of PCDDs is gradually decreased. The amount of high-chlorinated PCDDs emitted in diesel engine is larger than that of low-chlorinated PCDDs. The significant emission form of PCDD/Fs produced from diesel engines exhaust is a gas phase.

Asunto(s)