RESUMEN
The conversion of palm kernel shells (PKS), a major agricultural waste from the palm oil sector, into a potentially high-value biosorbent for heavy metals-contaminated wastewater treatments was explored in this work. Following carbonization, the activated PKS was chemically activated by soaking the biochar in a phosphoric acid (H3PO4) solution at 25 °C. The low-temperature approach benefits from less dangerous acid fume production and operational challenges when compared to the high-temperature procedure. The properties of the biochar were characterized by BET, FTIR, and SEM. The effects of H3PO4 dosage, initial Pb(II) concentration, and adsorbent dosage on removing Pb(II) from synthetic wastewater were investigated in the adsorption study. The activation of PKS biochar with high H3PO4 concentrations led to enhanced removal efficiency. The pseudo-second-order (PSO) kinetic model fitted the experimental data well (R2 0.99), indicating that chemisorption was likely involved in the adsorption of Pb(II) onto activated PKS. Pb(II) sorption was possibly promoted by the presence of phosphate moieties on the adsorbent surface. The Langmuir isotherm best described the sorption of Pb(II) onto the activated PKS (R2 0.97), giving the calculated maximum adsorption capacity (qm) of 171.1 µg/g. In addition to physical sorption, possible adsorption mechanisms included functional group complexation and surface precipitation. Overall, activating PKS biochar with H3PO4 at room temperature could be a promising technique to improve the adsorbent's adsorption efficiency for Pb(II) removal from wastewater.
RESUMEN
Among available technologies to remove heavy metals from wastewater, biosorption has gained more attention due to its high removal efficiency, friendly operation, and inexpensive cost. Despite many studies on metal adsorption from single ion solutions, kinetics and isotherms of binary metal ions simultaneously adsorbed onto biosorbents have not been thoroughly investigated to provide insight on involving mechanisms. This study explored the adsorption potential of untreated venus shells (UVS) that can be utilized in economical and environmentally-friendly ways. In this work, UVS of different sizes were prepared without chemical treatment as a biosorbent. Characterization of UVS was accomplished using nitrogen adsorption isotherm, FTIR, and SEM-EDX. Batch adsorption was carried out to study the effect of initial metal ion concentration, adsorbent dosage, and size on removing Cu(II) and Zn(II) from a binary solution of both metal ions using UVS. The experimental values of maximum adsorption capacities of Cu(II) and Zn(II) were 0.446 and 0.465 mg/g, respectively. The adsorption data were analyzed using the pseudo-first order, pseudo-second order, Elovich, and intraparticle diffusion rate equations. The pseudo-second order and the intraparticle diffusion model yielded the best fit to the experimental data for Cu(II) and Zn(II) ions, respectively. The equilibrium isotherm was examined using the Langmuir, Freundlich, Temkin, Dubinin-Radushkevich (D-R), and Elovich models. The Freundlich model best fits the Cu(II) and Zn(II) equilibrium adsorption data. The results indicated that the adsorption of Cu(II) and Zn(II) onto UVS-600 adsorbent could undergo a chemisorption mechanism. Both metal ions in an aqueous solution were competitively adsorbed onto the heterogeneous active sites available on the shell surfaces. Cu(II) and Zn(II) ions in the binary system could result in ionic interference between the adsorbed ions and the active sites.
RESUMEN
Photocatalytic oxidation purposes an economical and environmental friendly process to remove benzene from indoor air pollution. However, the process efficiency is primarily dependent on catalytic-film. The main purpose of this study is to synthesize pre-vulcanized latex impregnated with TiO2 (PVL-TiO2 thin film) from natural rubber to be used in photo-catalytic oxidation for benzene removal in a reactor. PVL-TiO2 thin films were synthesized for 3 different dosages of TiO2, which were 5%, 15%, and 25% The outcome of this study offers the new application of modified natural rubber in terms of environmental and health care protection. Morphology of the synthesized films was analyzed by SEM. The results showed that TiO2 particles could be well dispersed all over the surface of the film, in which the best distribution could be found for the PVL-TiO2 15% thin film. Tensile stress of the films was analyzed using ASTM D412. Results showed that the stress of the films got higher with the increasing amount of TiO2 content. This indicates that TiO2 strengthened the PVL-TiO2 film because the uniformly distribution of TiO2 on the inner surface increased the strength of the film. The decomposition of PVL and PVL-TiO2 thin films was analyzed using thermo gravimetric analysis. The maximum weight loss rates in the range of 1.536-1.145 wt%/°C attained at between 380 - 382 °C TiO2 particles enhanced thermal stability of PVL-TiO2 thin films due to the high decomposition temperature of its properties and also acted as barrier for the heat transfer of the films. Specific surface area (SSA) of the films was analyzed using Brunauer-Emmett-Teller. Specific surface area increased as the increasing content of TiO2, which corresponded to the morphology analysis by SEM. The analysis of chemical functional group of thin films was performed using ATR-FTIR. The results of Crystal identification using XRD clearly showed good attachment of rutile TiO2 on the films. Finally, results of absorbance spectrums and band gap energy showed that PVL not only peg TiO2 particles but also reducing band gap energy which induced by S and ZnO. Therefore, PVL-TiO2 thin films could be used under visible light condition. The films were then used in the study of benzene removal in annular reactor. The highest removal efficiency (83%)for the PVL-TiO2 15% thin film was obtained. Comparing to the maximum removal efficiency for PVL film (28%), roughly 60% increase in efficiency was achieved. The PCO kinetics were well fit by a first order Langmuir-Hinshelwood model. The calculation of oxidation rate and percentage of residual intermediates indicated that accumulation of residual intermediates can occur on the active site and the gas phase, resulting in increasing of residual intermediates. The successful synthesis of PVL-TiO2 thin film provides new opportunity to use natural rubber in terms of environmental and health care protection.