RESUMEN
PURPOSE: To verify the effect of abutment tooth location on the accuracy of digital impressions obtained using an intraoral scanner (IOS) for removable partial dentures (RPDs). METHODS: The target abutment teeth included the left first premolar (#34), second molar (#37), and right second premolar (#45) in a mandibular Kennedy class II model and the left and right second molars (#37, #47) in a class III model. Only #37 was isolated from the remaining teeth by the mucosal area in both models. Digital impressions were obtained using a desktop scanner (reference data) and an IOS (IOS data; scanning origin #37; n=10). The general trueness based on the entire model superimposition (TG), local trueness (TL) of an individual tooth, and dimensional accuracy (coordinate and linear accuracy) of the IOS data of the target abutment teeth were compared (α=0.05). RESULTS: In both models, #37 showed significantly inferior TG (P<0.01), superior TL (P<0.01), and mesial coordinate displacement (P<0.01 and P<0.05 in class II and III models, respectively). Intra-model comparisons showed that #45 in the class II model and #47 in the class III model had significantly inferior linear accuracy (P<0.05 and P<0.01, respectively) and buccal coordinate displacement (P<0.05 and P<0.01, respectively) compared with the other target teeth. CONCLUSIONS: In digital impressions of RPDs, isolation of abutment teeth by mucosal areas can reduce general trueness based on the entire dental arch and mesial tooth displacement, whereas increased distance from the scanning origin can adversely affect local trueness and dimensional accuracy.
RESUMEN
AIM: The purpose of this study was to investigate the accuracy of the measurement of palatal mucosa thickness using cone beam computed tomography (CBCT) and to create a conversion formula to evaluate palatal mucosa thickness more accurately. We then evaluated the palatal mucosa thickness in a Japanese population using CBCT and the conversion formula. MATERIALS AND METHODS: We evaluated palatal mucosa thickness in 10 healthy subjects at 15 sites using CBCT, digital impression, and K file. Multiple regression analysis was performed to create a conversion formula to measure thickness accurately. We then obtained CBCT data from 174 patients retrospectively, applied the conversion formula, and evaluated palatal mucosa thickness. RESULTS: Sites of measurement affected measurement error. Measurement using CBCT was 0.34 ± 0.04 mm smaller than actual measurement; therefore, a conversion formula was created. Male, age ≥60 years, and probing pocket depth ≥4 mm had significant and positive associations with palatal mucosa thickness; however, no association was observed between bleeding on probing and palatal mucosa thickness. CONCLUSION: CBCT is useful for the noninvasive and accurate measurement of palatal mucosa thickness.
Asunto(s)
Tomografía Computarizada de Haz Cónico , Hueso Paladar , Humanos , Masculino , Membrana Mucosa , Hueso Paladar/diagnóstico por imagen , Estudios RetrospectivosRESUMEN
Controversy prevails over the effect of overglazing on the fracture strength of ceramic materials. Therefore, the effects of different surface finishes on the compressive fracture strength of machinable ceramic materials were investigated in this study. Plates prepared from four commercial brands of ceramic materials were either surface-polished or overglazed (n=10 per ceramic material for each surface finish), and bonded to flat surfaces of human dentin using a resin cement. Loads at failure were determined and statistically analyzed using two-way ANOVA and Bonferroni test. Although no statistical differences in load value were detected between polished and overglazed groups (p>0.05), the fracture load of Vita Mark II was significantly lower than those of ProCAD and IPS Empress CAD, whereas that of IPS e.max CAD was significantly higher than the latter two ceramic materials (p<0.05). It was concluded that overglazed and polished surfaces produced similar compressive fracture strengths irrespective of the machinable ceramic material tested, and that fracture strength was material-dependent.