RESUMEN
Liquid-liquid phase separation is a phenomenon within biology whereby proteins can separate into dense and more dilute phases with distinct properties. Three antibodies that undergo liquid-liquid phase separation were characterized in the protein-rich and protein-poor phases. In comparison to the protein-poor phase, the protein-rich phase demonstrates more blue-shift tryptophan emissions and red-shifted amide I absorbances. Large changes involving conformational isomerization around disulfide bonds were observed using Raman spectroscopy. Amide I and protein fluorescence differences between the phases persisted to temperatures above the critical temperature but ceased at the temperature at which aggregation occurred. In addition, large changes occurred in the structural organization of water molecules within the protein-rich phase for all three antibodies. It is hypothesized that as the proteins have the same chemical potential in both phases, the protein viscosity is higher in the protein-rich phase resulting in slowed diffusion dependent protein aggregation in this phase. For all three antibodies we performed accelerated stability studies and found that the protein-rich phase aggregated at the same rate or slower than the protein-poor phase.
Asunto(s)
Anticuerpos Monoclonales , Espectrometría Raman , Anticuerpos Monoclonales/química , Concentración de Iones de Hidrógeno , TemperaturaRESUMEN
Subvisible particle formation, which occurs after the sterile filtration step of the fill/finish process, is a challenge that may occur during the development of biotherapeutics with complex molecular structures. Here, we show that a stainless steel pump head from a rotary piston pump produces more protein aggregates, past the limit of the acceptable quality range for subvisible particle counts, in comparison to a ceramic pump head. The quartz crystal microbalance was used to quantify the primary layer, proteins irreversibly adsorbed at the solid-liquid interface, and the secondary diffuse gel-like layer interacting on top of the primary layer. The results showed that the mass of protein irreversibly adsorbed onto stainless steel sensors is greater than on an aluminum oxide surface (ceramic pump mimic). This suggests that the amount of adsorbed protein plays a role in surface-induced protein aggregation at the solid-liquid interface.
Asunto(s)
Anticuerpos Monoclonales Humanizados/química , Composición de Medicamentos/métodos , Fragmentos Fc de Inmunoglobulinas/química , Inmunoglobulina G/química , Acero Inoxidable/química , Factor de Necrosis Tumoral alfa/química , Adsorción , Óxido de Aluminio/química , Anticuerpos Monoclonales Humanizados/genética , Cerámica/química , Estabilidad de Medicamentos , Fragmentos Fc de Inmunoglobulinas/genética , Inmunoglobulina G/genética , Agregado de Proteínas , Tecnicas de Microbalanza del Cristal de Cuarzo , Propiedades de Superficie , Factor de Necrosis Tumoral alfa/genéticaRESUMEN
Passage of specific protein solutions through certain pumps, tubing, and/or filling nozzles can result in the production of unwanted subvisible protein particles (SVPs). In this work, surface-mediated SVP formation was investigated. Specifically, the effects of different solid interface materials, interfacial shear rates, and protein concentrations on SVP formation were measured for the National Institute of Standards and Technology monoclonal antibody (NISTmAb), a reference IgG1 monoclonal antibody (mAb). A stainless steel rotary piston pump was used to identify formulation and process parameters that affect aggregation, and a flow cell (alumina or stainless steel interface) was used to further investigate the effect of different interface materials and/or interfacial shear rates. SVP particles produced were monitored using flow microscopy or flow cytometry. Neutron reflectometry and a quartz crystal microbalance with dissipation monitoring were used to characterize adsorption and properties of NISTmAb at the stainless steel interface. Pump/shear cell experiments showed that the NISTmAb concentration and interface material had a significant effect on SVP formation, while the effects of interfacial shear rate and passage number were less important. At the higher NISTmAb concentrations, the adsorbed protein became structurally altered at the stainless steel interface. The primary adsorbed layer remained largely undisturbed during flow, suggesting that SVP formation at high NISTmAb concentration was caused by the disruption of patches and/or secondary interactions.