RESUMEN

The research proposed a novel method of obtaining sorption material from readily available Acorus calamus biomass through a combination of physical and chemical activation processes. The material with the highest specific surface area (1652 m2 g-1) was obtained by physical activation with CO2, followed by chemical activation with KOH. Reversing the order of activation methods resulted in a lower specific surface area (1014 m2 g-1) of the carbon sample. Chemical activation produced activated carbon with a surface area of 1066 m2 g-1-, while physical activation produced 390 m2 g-1. This confirms the synergistic effect of combining the two activation methods for biocarbon. It was observed that physical activation with CO2 generates a diverse range of pores, including meso- and macropores, while chemical activation induces the formation of micropores. In contrast, reversing the order of these processes leads to the degradation of the porous structure. The application of physical-chemical activation with synergistic effects represents a significant advancement in producing high-quality activated biocarbon for various applications, such as wastewater treatment and energy storage. The combination of the two activation methods resulted in a synergistic effect, leading to the production of carbon material of higher quality. Additionally, the diversified pore sizes will enable the sorption of various pollutants in the aquatic environment and air pollutants, where gas particles are much smaller.

Asunto(s)

RESUMEN

Waste biomass, a renewable energy source, is inexpensive material that has great potential in sorption and electrochemical application. The selected waste materials (corncobs, coconut shells, walnuts, and pistachio husks) allow to close the production cycle and enable material recycling, which are important aspects in the hierarchy of waste management. The proposed methodology for production and activation of biochars can be used industrially due to highly porous structure, developed surface area, and sorption ability of the obtained activated carbons (AC). A significant increase (from 4 up to more than 10 times) in specific surface area (SSA) is observed for all samples after the CO2 activation process (0.5 h at 800 °C) up to 725 m2 g-1 for corncobs, 534.9 m2 g-1 for pistachio husks, 523 m2 g-1 for coconut shells, and 393 m2 g-1 for walnut husks. The highest value of SSA is achieved for the AC derived from corncobs. This material is evaluated for use as an adsorbent, revealing 99% removal of Rhodamine B (dye/AC ratio of 0.0017) and 69% removal of chromium (dye/AC ratio of 0.0028). Based on the adsorption kinetics analysis, it is demonstrated that the Cr(VI) undergoes physical adsorption, while RhB undergoes chemisorption. In addition, corncob-derived AC exhibits superior electrochemical performance in 6 M KOH compared to the nonactivated biochar. A specific capacitance of 70 F g-1 at 5 A g-1 is achieved, along with outstanding rate capability (45 F g-1 at 50 A g-1) and cycling stability (94% at 10 A g-1 after 10,000 cycles). In contrast, the nonactivated sample shows only 34 F g-1 at 5 A g-1 and 13 F g-1 at 50 A g-1, with a stability of 91.4%.

Asunto(s)

RESUMEN

Leather processing companies are struggling with the problem of increasing costs of post-production waste disposal. Therefore, the issue of thermal waste disposal at the plant and the use of generated heat in the production process is becoming more and more popular. Leather waste on its own does not allow for autothermal combustion despite the sufficient higher heating value (HHV). Therefore the Authors proposed to improve the flammability of the fuel by adding a small amount of wood sawdust to leather waste and produce premixed pellets. Six such samples were incinerated in a laboratory-scale reactor, which enables the simultaneous measurement of characteristic temperatures, exhaust gas analysis and sample mass loss rate. Research has shown that even a small addition of sawdust enables a stable combustion process and does not cause the formation of sinters. In addition, studies of the ash showed that in the case of chromium-containing waste, a large part of it remained in the ash in the form of Cr2O3. Nevertheless, very fine ash causes the small fraction chromium to be carried with the flue gas stream, therefore controlled agglomeration of the ash structure would be advisable in the final installation. Emission analysis showed high and moderately high NOx and SO2 emissions, decreasing with the increase in the amount of sawdust addition in the sample. Research has shown that leather waste is not a burden, but can be an attractive and safe source of energy for the company, while improving waste management in a circular economy.

Asunto(s)

RESUMEN

The thermal pyrolysis of agriculture biomass has been studied in a fixed-bed reactor, where the pyrolysis was conducted at a steady temperature of 800 °C. This work analyses the pyrolysis products of six agricultural wastes: pistachio husks, walnut husks, sunflower hulls, buckwheat husks, corncobs and coconut shells. The conducted research compared examples of large waste biomass streams from different parts of the world as a potential source of renewable energy. Additionally, the kinetics of the reaction with the activation energy were analyzed and calculated for all raw materials in pyrolysis process. Biochars are characterised by higher combustion heat in comparison to the raw material samples. The average value of the heat of combustion increased due to pyrolysis process from 10 MJ/kg, with minimal value of 2.7 MJ/kg (corncob) and maximum of 13.0 MJ/kg for coconut, which is also characterised by the maximal absolute combustion heating value (32.3 MJ/kg). The increase in calorific values varied from 15% to 172% (with 54% reference for wood chips), which indicates that charring is an effective method for increasing the energy concentration. The obtained biochar were compared with wood chips, which are widely used solid fuel of organic origin. The studied biomass-derived fuels are characterised by lower ash contribution than wood. An analogous observation was made for the obtained biochars, whose ash contribution was lower than for the chips in terms of both unit-mass and unit-combustion-heat. The main advantage of this method is the production of solid fuel from biomass, which increases the calorific value and bulk density of biochar in comparison to raw material.

RESUMEN

The routine pruning and cutting of fruit trees provides a considerable amount of biowaste each year. This lignocellulosic biomass, mainly in the form of branches, trunks, rootstocks, and leaves, is a potential high-quality fuel, yet often is treated as waste. The results of a feasibility study on biochar production by pyrolysis of residues from orchard pruning were presented. Three types of biomass waste were selected as raw materials and were obtained from the most common fruit trees in Poland: apple (AP), pear (PR), and plum (PL) tree prunings. Two heating rates and three final pyrolysis temperatures were applied. For the slow (SP) and fast pyrolysis (FP) processes, the heating rates were 15 °C/min and 100 °C/min, respectively. The samples were heated from 25 °C up to 400, 500, and 600 °C. Chemical analyses of the raw materials were conducted, and the pyrolysis product yields were determined. A significant rise of higher heating value (HHV) was observed for the solid pyrolysis products, from approximately 23.45 MJ/kg for raw materials up to approximately 29.52 MJ/kg for pyrolysis products at 400 °C, and 30.53 MJ/kg for pyrolysis products at 600 °C. Higher carbon content was observed for materials obtained by fast pyrolysis conducted at higher temperatures.

RESUMEN

Tires, conveyor belts, floor mats, and shoe soles form a main-stream of rubber waste. The amount of these used materials continuously increases due to development of the rubber market. Therefore, pro-ecological utilization (i.e., energy recycling instead of burning) and recovering valuable and recyclable materials becomes an urgent necessity. In this regard, this work was devoted to the chemical recycling of selected used rubber products, and it especially explores the possibility of limonene production. Different types of waste rubber were characterized and pyrolyzed at microgram and laboratory scales, and the results were compared. Additionally, the pyrolysis of tires, the most significant stream of rubber waste, was also conducted in a semi-technical scale reactor. The effectiveness of limonene formation in the liquid fractions obtained from different types of waste rubber was compared.

RESUMEN

In this work, we present the preparation and characterization of biomass-derived activated carbon (AC) in view of its application as electrode material for electrochemical capacitors. Porous carbons are prepared by pyrolysis of chestnut seeds and subsequent activation of the obtained biochar. We investigate here two activation methods, namely, physical by CO2 and chemical using KOH. Morphology, structure and specific surface area (SSA) of synthesized activated carbons are investigated by Brunauer-Emmett-Teller (BET) technique and scanning electron microscopy (SEM). Electrochemical studies show a clear dependence between the activation method (influencing porosity and SSA of AC) and electric capacitance values as well as rate capability of investigated electrodes. It is shown that well-developed porosity and high surface area, achieved by the chemical activation process, result in outstanding electrochemical performance of the chestnut-derived porous carbons.

RESUMEN

The aim of this study was to assess the possibility of using furniture waste for smokeless fuel production using the pyrolysis process. Four types of wood-based wastes were used in the pyrolysis process: pine sawdust (PS), chipboard (CB), medium-density fiberboard (MDF), and oriented strand board (OSB). Additionally, the slow and fast types of pyrolysis were compared, where the heating rates were 15 °C/min and 100 °C/min, respectively. Chemical analyses of the raw materials and the pyrolysis product yields are presented. A significant calorific value rise was observed for the solid pyrolysis products (from approximately 17.5 MJ/kg for raw materials up to approximately 29 MJ/kg for slow pyrolysis products and 31 MJ/kg for fast pyrolysis products). A higher carbon content of char was observed in raw materials (from approximately 48% for raw materials up to approximately 75% for slow pyrolysis products and approximately 82% for fast pyrolysis products) than after the pyrolysis process. This work presents the possibility of utilizing waste furniture material that is mostly composed of wood, but is not commonly used as a substrate for conversion into low-emission fuel. The results prove that the proposed solution produced char characterized by the appropriate properties to be classified as smokeless coal.

RESUMEN

Pyrolysis of straw pellets and wood strips was performed in a fixed bed reactor. The chars, solid products of thermal degradation, were used as potential materials for activated carbon production. Chemical and physical activation processes were used to compare properties of the products. The chemical activation agent KOH was chosen and the physical activation was conducted with steam and carbon dioxide as oxidising gases. The effect of the activation process on the surface area, pore volume, structure and composition of the biochar was examined. The samples with the highest surface area (1349.6 and 1194.4 m2/g for straw and wood activated carbons, respectively) were obtained when the chemical activation with KOH solution was applied. The sample with the highest surface area was used as an adsorbent for model wastewater contamination removal.

RESUMEN

This review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste tyres, a comprehensive evaluation was carried out to show the main effect of process conditions (heating rate, temperature, pressure, carrier gas flow rate, and type of volatile residence and process times) for different pyrolytic methods and types of apparatus on the yield of limonene. All the results cited are given in the context of the pyrolysis method and the type of reactor, as well as the experimental conditions in order to avoid contradictions between different researchers. It is shown that secondary and side reactions are very sensitive to interaction with the above-mentioned variables. The yields of all pyrolytic products are also given, as background for limonene, the main product reported in this study.

RESUMEN

This article covers new application for char as a carrier of phase-change materials (PCM) that could be used as an additive to building materials. Being composed of bio-char and PCM, the granulate successfully competes with more expensive commercial materials of this type, such as Micronal® PCM. As a PCM carrier, char that was obtained from the pyrolysis of chestnut fruit (Aesculus hippocastanum) with different absorbances of the model phase-change material, Rubitherm RT22, was tested. DSC analysis elucidated several thermal properties (such as enthalpy, phase transition temperature, and temperature peak) of those mixtures and the results were compared with a commercial equivalent, Micronal DS 5040 X. Comparative research, approximating realistic conditions, were also performed by cooling and heating samples in a form of coatings that were made from chars with different content of RT22. These results indicated that the use of char as a PCM carrier was not only possible, but also beneficial from a thermodynamic point of view and it could serve as an alternative to commercial products. In this case, adsorption RT22 into char allowed for temperature stabilization comparable to Micronal DS 5040 X with ease of use as well as the economic advantages of being very low cost to produce due to microencapsulation. Other advantage of the proposed solution is related with the application of char obtained from waste biomass pyrolysis as a PCM carrier, and using this product in building construction to improve thermal comfort and increase energy efficiency.