RESUMEN

The enhancement of photocatalytic activity of TiO2 can be made either by promoting absorption efficiency of photon energy or by reducing recombination losses of photogenerated charge carriers, for which fabrication of nanocomposite structure with carbon materials is an optional selection. Among various nanocarbons, graphene (G), graphene oxide (GO), and reduced graphene oxide (rGO) are more favorable as the counterpart materials because they can provide availability of both obverse and reverse surface, thus doubling effective sites for adsorption, loading of nanoparticles, and interfacial interaction with the loaded nanoparticles. Composition of G/GO with titania, therefore, is a hopeful strategy for achieving synergy or cooperative effect in photocatalysis. In this personal account, we focus on the background and methodology of several soft chemical approaches that we have utilized up to date to fabricate nanocomposites of G/GO and titania, aiming to shed light on the importance of designing of nanocomposite structure for enhancing photocatalysis. In addition, we emphasize the role of interfacial interaction between carbon and titania by exemplifying a hybridized photocatalyst based on inexpensive biomass-derived carbon sphere (CS), and demonstrate that it is a crucial influential factor underlying an enhanced visible light photocatalysis. CS can be a better selection as a counterpart component than G/GO, whose core-shell composing structure with titania (TiO2 @CS) can efficiently induce charge transfer so as to achieve a much higher photocatalytic performance under visible light illumination as compared to the composite of rGO and titania.

RESUMEN

This study presents a rare use of layered double hydroxides of Fe(II) and Al(III) (Fe-Al LDH), as reported for the first time for bromate removal from aqueous solutions. The Fe-Al LDH samples were prepared with Fe/Al molar ratios of 1-4 using a co-precipitation method at pH 7, with subsequent hydrothermal treatment at 120°C. The Fe-Al LDH (molar ratio of Fe/Al=1, 2) with a layered structure exhibited nearly complete removal of bromate from initial concentration of 100µmol/dm(3) at a wide pH range of 4.0-10.5 over a 2h reaction period; the residual bromate concentration in the solution was lower than the detection limit of 0.07µmol/dm(3) (9µg-BrO(3)(-)/dm(3)). During the reaction period, bromide was released into the solution via a reduction process. Reactivity of Fe-Al LDH with a Fe/Al molar ratio of 2 did not decrease the bromate reduction efficiency during 30days.

Asunto(s)

RESUMEN

A novel layered double hydroxide of Mg and Al with composition [Mg(0.96)Al(4.00)(OH)(12)]Cl(1.86)(CO(3))(0.03)·2.4H(2)O, designated as MgAl(4)-Cl, was synthesized by mixing crystalline gibbsite (γ-Al(OH)(3)) and solid MgCl(2)·6H(2)O with subsequent hydrothermal treatment at 160 °C for 72h. The MgAl(4)-Cl exhibited a crystalline material of a layered structure, as evidenced from X-ray diffraction. Anion uptake experiments with the MgAl(4)-Cl showed that Cl(-) in the interlayer space can be exchanged with anions such as Br(-), H(2)PO(4)(-), CO(3)(2-) or dodecyl sulfate (DS(-)) from aqueous solutions with preservation of the layered structure. Uptake of NO(3)(-), BrO(3)(-) or SO(4)(2-) on the MgAl(4)-Cl showed different behavior; these anions can be exchanged within 1h maintaining the layered structure, but a release of Mg(2+) cations from the sample was observed with increased reaction time, resulting in collapse of the layered structure and formation of the gibbsite phase, as determined from chemical analyses and X-ray diffraction.

Asunto(s)

RESUMEN

We prepared a novel Zr-modified MgFe-LDH(CO(3)) composite by adding a mixed solution of MgCl(2), FeCl(3), and ZrOCl(2) and another mixed solution of 1mol/dm(3) NaOH and 1mol/dm(3) Na(2)CO(3) to distilled water at a constant pH of 10. The composite exhibited only a poorly crystalline structure, resembling that of layered double hydroxides (LDH) from X-ray diffraction. The phosphate uptake is dependent on pH, decreasing with an increase in pH. This composite shows a much greater uptake of phosphate ions in P-enriched seawater (0.33mg-P/dm(3)) than amorphous zirconium oxide and MgFe-LDH(CO(3)). The uptake isotherm was fitted with a Freundlich relation. These phosphate-uptake behaviors closely resemble those of the relevant Zr-MgAl-LDH, which is estimated to be a composite of MgAl-LDH with amorphous zirconium hydroxide on the surface from X-ray absorption spectroscopy. Therefore, a similar structure of Zr-modified MgFe-LDH(CO(3)) composite probably causes the marked increase in phosphate uptake from P-enriched seawater.

Asunto(s)

Asunto(s)

Asunto(s)

RESUMEN

Lights? Nanotubes? Action! A hydrogel comprising lysozymes, poly(ethylene glycol), phospholipids, and functionalized single-walled carbon nanotubes is employed for light-driven thermoelectric conversion. A photoinduced thermoelectric conversion module based on the hydrogel functions as a novel electric power generator (see image). This concept may find application in various industries, such as robotics and aerospace engineering.

Asunto(s)

RESUMEN

We have developed a near-infrared laser-driven carbon nanotube (CNT) microdevice. Powerful photo-exothermy of CNT was coupled with a microdevice for remote control of temperature-dependent biocatalytic transformations. We succeeded in ultrafast temperature change (<0.03 s), wide range of controlled temperature (25-55 degrees C) and high-precision thermal cycle in a microspace owing to the following physical factors: (1) high efficiency of photothermal conversion of the CNTs; (2) high thermal conductivity of the CNTs; and (3) low heat capacity of the microspaces. Furthermore, this is the first report, supported by direct observations, of the optical control of biocatalytic reactions, such as DNA extension, DNA amplification and enzymatic cyclodextrin production, by employing a laser-triggered CNT microdevice. Our present work constitutes important progress for various lab-on-a-chip applications.

Asunto(s)

Asunto(s)

RESUMEN

A novel composite composed of tubular titanate-two dimensionally deposited carbon nanosheets was prepared with carbon nanosheets as templates through intercalation and hydrothermal treatment; this nanotube-based composite and its calcined products exhibit both excellent adsorptivity and high photocatalytic activity toward organic molecules.

Asunto(s)

RESUMEN

Nanocarbons, such as carbon nanohorns (CNH) and carbon nanotubes, are materials of interest in many fields of science and technology because of their remarkable physical properties. We report here a novel approach for using NIR laser-driven CNH as an antiviral agent. NIR laser-driven functional CNH complexes could open the way to a new range of antiviral materials.

RESUMEN

We synthesized Zr(4+) incorporated MgAl-layered double hydroxides, Mg(AlZr)-LDH(A) (where A denotes a counteranion in the interlayer space and is expressed as CO(3) for carbonate and Cl for chloride ions), with different molar ratios of Mg/(Al+Zr). Then we characterized their uptake behavior toward phosphate ions. CO(3)-type tertiary LDH materials synthesized at room temperature show low crystallinity, whereas the highly crystalline Cl-type tertiary LDH, [Mg(0.68)Al(0.17)Zr(0.14)(OH)(2)][Cl(0.26)(CO(3))(0.04)1.24H(2)O], was synthesized for the first time using a hydrothermal treatment at 120 degrees C. The distribution coefficients (K(d)) of oxo-anions were measured with a mixed solution containing trace amounts of the anions. The selectivity sequences were Cl(-), NO(-)(3)

RESUMEN

Rhizopus oryzae MYA-2483, which cannot utilize D-psicose as a sole source of carbon, converted D-psicose to two other compounds. These compounds were identified by NMR and IR as D-tagatose and D-talitol. In this study, we describe for the first time the bioconversion of D-psicose to D-tagatose. Various strains of Mucoraceae fungi, to which R. oryzae MYA-2483 belongs, exhibited conversion activity similar to that of R. oryzae MYA-2483. There is the possibility that a considerable number of fungi belonging to Mucoraceae possess such D-psicose conversion activity.

Asunto(s)

RESUMEN

Ce(IV)-loaded Y-zeolites (CeY) were prepared for selective removal of the trace amount of organic sulfur compounds from hydrodesulfurization (HDS)-treated diesel oil. The CeY samples can be obtained from NH4-Y-zeolite (NH4Y) using liquid-phase ion-exchange and solid-state ion-exchange methods. The ion-exchange reactions, structures, and selective adsorptions of organic sulfur compounds of the CeY samples were investigated using XRD, IR, XPS, TEM, and GC sulfur analyzer. The organic sulfur compound uptakes strongly depend on the amount and the valency of Ce in the zeolite structure. Ce(IV) shows much higher adsorptive ability than Ce(III). A CeY-S sample prepared by solid-state ion-exchange reaction of NH4Y and Ce(NO3)3 with Ce/NH4 mole ratio of 0.63 at 250 degrees C showed a maximum sulfur uptake from a model solution of HDS-treated gasoline containing thiophene [S = 5 ppm (ppm = mg/L)]. A desulfurization from a HDS-treated diesel oil containing organic sulfur compounds (S = 1.87 ppm) and H2S (S = 0.73 ppm) was investigated with a combination of the CeY-S and a CuO adsorbent for removal of H2S by a batch method. The sulfur content was reduced to below 0.01 ppm for the first time. This method provides a promising desulfurization process to prepare a clean fuel for fuel cells.

RESUMEN

Low crystalline iron hydroxides such as goethite (alpha-FeOOH) and akaganeite (beta-FeOOH) were synthesized, and the selective adsorption of phosphate ions from phosphate-enriched seawater was examined. The results of the distribution coefficients (K(d)) of oxoanions in mixed anion solutions at pH 8 follow the selectivity order Cl-, NO3-, SO4(2-) << CO3(2-), HPO4(2-) for goethite, and Cl-, CO3(2-) < NO3- < SO4(2) << HPO4(2-) for akaganeite. In seawater, both adsorbents show high selectivity for phosphate ions despite the presence of large amounts of major cations and anions in seawater. The adsorption isotherms fitted better with the Freundlich equation and the maximum uptake of phosphate from phosphate-enriched seawater was 10 mg P/g at an equilibrium phosphate concentration of 0.3 mg P/L on both adsorbents. The phosphate adsorption/desorption cycles show that akaganeite is an excellent adsorbent even after 10 cycles and its chemical stability is good.

RESUMEN

Phosphate adsorption from single electrolyte (NaH2PO4), phosphate-enriched seawater, and model wastewater was studied using amorphous zirconium hydroxide, ZrO(OH)2(Na2O)0.05 1.5H2O, as an adsorbent. Batch experiments were carried out to investigate the adsorption of phosphate. The effect of pH on phosphate adsorption from seawater showed that the uptake of phosphate increased with an increase in pH up to 6, and then decreased sharply with a further increase in pH of the solution. The equilibrium data of phosphate adsorption were followed with a Freundlich isotherm. The uptake of phosphate at the adsorbent/solution ratio 0.05 g/2 L was 10 and 17 mg-P/g for the phosphate-enriched seawater and the model wastewater, respectively. A much higher adsorptivity toward phosphate ions in seawater was observed on ZrO(OH)2(Na2O)0.05 1.5H(2)O than on other representative adsorbents based on layered double hydroxides of Mg(II)-Al(III), Mg(II)-Fe(III), and Ni(II)-Fe(III). The effective desorption of phosphate ions on ZrO(OH)2(Na2O)0.05 1.5H2O could be achieved using a 0.1 M NaOH solution. The usefulness of experimental data for practical applications in removing phosphate in seawater and wastewater is discussed.

Asunto(s)

RESUMEN

Adsorptive properties of MgMn-3-300 (MgMn-type layered double hydroxide with Mg/Mn mole ratio of 3, calcined at 300 degrees C) for phosphate were investigated in phosphate-enriched seawater with a concentration of 0.30 mg-P/dm3. It showed the highest phosphate uptake from the seawater among the inorganic adsorbents studied (hydrotalcite, calcined hydrotalcite, activated magnesia, hydrous aluminum oxide, manganese oxide (delta-MnO2)). The phosphate uptake by MgMn-3-300 reached 7.3 mg-P/g at an adsorbent/solution ratio of 0.05 g/2 dm3. The analyses of the uptakes of other constituents (Na+, K+, Ca(+, Cl-, and SO(2-)4) of seawater showed that the adsorbent had a markedly high selectivity for the adsorption of phosphate ions. Effects of initial phosphate concentration, temperature, pH, and salinity on phosphate uptake were investigated in detail by a batch method. The phosphate uptake increased slightly with an increase in the adsorption temperature. The adsorption isotherm followed Freundlich's equation with constants of logK(F)=1.25 and 1/n=0.65, indicating that it could effectively remove phosphate even from a solution of markedly low phosphate concentration as well as with large numbers of coexisting ions. The pH dependence showed a maximum phosphate uptake around pH 8.5. The pH dependence curve suggested that selective phosphate adsorption progresses mainly by the ion exchange of HPO(2-)4. The study on the effect of salinity suggested the presence of two kinds of adsorption sites in the adsorbent: one nonspecific site with weak interaction and one specific site with strong interaction. The effective desorption of phosphate could be achieved using a mixed solution of 5 M NaCl + 0.1 M NaOH (1 M = 1 mol/dm3), with negligible dissolution of adsorbent. The adsorbent had high chemical stability against the adsorption/desorption cycle; it kept a good phosphate uptake even after the repetition of the seventh cycle.

Asunto(s)

RESUMEN

Adsorption of the organic sulfur compounds thiophene (TP) and 1-benzothiophene (1-BTP) in an organic model solution of hydrodesulfurizated gasoline (heptane with 1 wt% toluene and 0.156 mM (5 ppmw as sulfur) TP or 1-BTP) was studied by a batch method at 80 degrees C using metal-ion-exchanged Y-zeolites. Although NaY-zeolite or its acid-treated material rarely adsorbed the organic sulfur compounds, NaY-zeolites exchanged with Ag+, Cu2+, and Ce3+ ions and NH(4)Y-zeolites exchanged with Ce3+ ions showed markedly high adsorptive capacities for TP and 1-BTP. The sulfur uptake increased in the order CuY-zeolite(Na)

Asunto(s)