RESUMEN

We report on an all-fiber setup capable of generating complex intensity patterns using interference of few guided modes. Comprised by a few-mode fiber (FMF) spliced to a multimodal interference (MMI) fiber device, the setup allows for obtaining different output patterns upon adjusting the phases and intensities of the modes propagating in the FMF. We analyze the output patterns obtained when exciting two family modes in the MMI device using different phase and intensity conditions for the FMF modal base. Using this simple experimental arrangement we are able to produce complex intensity patterns with radial and azimuthal symmetry. Moreover, our results suggest that this approach provides a means to generate beams with orbital angular momentum (OAM).

RESUMEN

We present a combination of light-sheet excitation and two-dimensional fluorescence intensity ratio (FIR) measurements as a simple and promising technique for three-dimensional temperature mapping. The feasibility of this approach is demonstrated with samples fabricated with sodium yttrium fluoride nanoparticles co-doped with rare-earth ytterbium and erbium ions (NaYF4:Yb3+/Er3+) incorporated into polydimethylsiloxane (PDMS) as a host material. In addition, we also evaluate the technique using lipid-coated NaYF4:Yb3+/Er3+ nanoparticles immersed in agar. The composite materials show upconverted (UC) fluorescence bands when excited by a 980 nm near-infrared laser light-sheet. Using a single CMOS camera and a pair of interferometric optical filters to specifically image the two thermally-coupled bands (at 525 and 550 nm), the two-dimensional FIR and, hence, the temperature map can be readily obtained. The proposed method can take optically sectioned (confocal-like) images with good optical resolution over relatively large samples (up to the millimetric scale) for further 3D temperature reconstruction.

RESUMEN

Optical fiber sensors incorporating luminescent materials are useful for detecting physical parameters and biochemical species. Fluorescent materials integrated on the tips of optical fibers, for example, provide a means to perform fluorescence thermometry while monitoring the intensity or the spectral variations of the fluorescence signal. Similarly, certain molecules can be tracked by monitoring their characteristic emission in the UV wavelength range. A key element for these sensing approaches is the luminescent composite, which may be obtained upon allocating luminescent nanomaterials in glass or polymer hosts. In this work, we explore the fluorescence features of two composites incorporating lanthanide-doped fluorescent powders using polydimethylsiloxane (PDMS) as a host. The composites are obtained by a simple mixing procedure and can be subsequently deposited onto the end faces of optical fibers via dip coating or molding. Whereas one of the composites has shown to be useful for the fabrication of fiber optic temperature sensors, the other shows promising result for detection of UV radiation. The performance of both composites is first evaluated for the fabrication of membranes by examining features such as fluorescent stability. We further explore the influence of parameters such as particle concentration and density on the fluorescence features of the polymer blends. Finally, we demonstrate the incorporation of these PDMS fluorescent composites onto optical fibers and evaluate their sensing capabilities.

RESUMEN

We demonstrate optical fiber sensors based on highly coupled multicore fibers operating with the optical Vernier effect. The sensors are constructed using a simple device incorporating single-mode fibers (SMFs) and a segment of a multicore fiber. In particular, we evaluated the performance of a sensor based on a seven-core fiber (SCF) spliced at both ends to conventional SMFs, yielding a versatile arrangement for realizing Vernier-based fiber sensors. The SMF-SCF-SMF device can be fabricated using standard splicing procedures and serve as a "building block" for both, reflection and transmission sensing configurations. As demonstrated with our experimental results, the Vernier arrangements can yield a ten-fold increase in sensitivity for temperature measurements compared to a conventional single SMF-SCF-SMF device, thereby confirming the enhanced sensitivity that can be attained with this optical effect. Furthermore, through theoretical analysis, we obtain the relevant parameters that must be optimized in order to achieve an optimal sensitivity for a specific application. Our findings thus provide the necessary guidelines for constructing Vernier-based sensors with all-fiber devices based on highly coupled multicore optical fibers, which constitutes an ideal framework to develop highly sensitive fiber sensors for different applications.

RESUMEN

We demonstrate a fiber optic probe incorporating functional polymer composites for controlled generation of photothermal effects. The probe combines carbon-based and rare-earth composites on the tip of standard multimode fibers, thus yielding a compact fiber optic photothermal probe (FOPP) whose temperature can be measured simultaneously through fluorescent thermometry. We evaluate the thermal features of the probe through experiments and numerical calculations showing that large thermal gradients are obtained within the vicinity of the heating zone. The temperatures achieved with the FOPP are within the ranges of interest for hyperthermia and can be attained using low optical powers (< 280 mW).

RESUMEN

We demonstrate a novel structure based on smart carbon nanocomposites intended for fabricating laser-triggered drug delivery devices (DDDs). The performance of the devices relies on nanocomposites' photothermal effects that are based on polydimethylsiloxane (PDMS) with carbon nanoparticles (CNPs). Upon evaluating the main features of the nanocomposites through physicochemical and photomechanical characterizations, we identified the main photomechanical features to be considered for selecting a nanocomposite for the DDDs. The capabilities of the PDMS/CNPs prototypes for drug delivery were tested using rhodamine-B (Rh-B) as a marker solution, allowing for visualizing and quantifying the release of the marker contained within the device. Our results showed that the DDDs readily expel the Rh-B from the reservoir upon laser irradiation and the amount of released Rh-B depends on the exposure time. Additionally, we identified two main Rh-B release mechanisms, the first one is based on the device elastic deformation and the second one is based on bubble generation and its expansion into the device. Both mechanisms were further elucidated through numerical simulations and compared with the experimental results. These promising results demonstrate that an inexpensive nanocomposite such as PDMS/CNPs can serve as a foundation for novel DDDs with spatial and temporal release control through laser irradiation.

Asunto(s)

Portadores de Fármacos/química , Nanocompuestos/química , Materiales Inteligentes/química , Carbono/química , Dimetilpolisiloxanos/química , Portadores de Fármacos/efectos de la radiación , Elasticidad , Rayos Láser , Luz , Fenómenos Mecánicos , Nanocompuestos/efectos de la radiación , Rodaminas/química , Materiales Inteligentes/efectos de la radiación

RESUMEN

We demonstrate a novel and simple means to fabricate optical fiber immunosensors based on Fabry-Perot (F-P) interferometers using polydimethylsiloxane (PDMS) as support for bioactive lipids. The sensors are fabricated following a straightforward dip-coating method producing PDMS end-capped devices. A biosensing platform is realized by subsequent functionalization of the PDMS cap with a previously characterized bioactive lipid antigen cocktail from Mycobacterium fortuitum, used as a surrogate source of antigens for tuberculosis diagnosis. After functionalization of the PDMS, the F-P sensors were immersed in different antibody-containing sera and the registered changes in their spectral features were associated to the interactions between the active lipids and the serum antibodies. Our results show that the proposed PDMS end-capped F-P immunosensors perform well differentiating antibody-containing sera. Furthermore, they offer attractive attributes such as label-free operation, real-time detection capabilities and they are also reusable. The proposed sensors, therefore, serve as an enabling optical immunosensing technique offering excellent potential for developing novel lipidomic analytical tools.

RESUMEN

Photothermal therapy has shown to be a promising technique for local treatment of tumors. However, the main challenge for this technique is the availability of localized heat sources to minimize thermal damage in the surrounding healthy tissue. In this work, we demonstrate the use of optical fiber microheaters for inducing thermal lesions in soft tissue. The proposed devices incorporate carbon nanotubes or gold nanolayers on the tips of optical fibers for enhanced photothermal effects and heating of ex vivo biological tissues. We report preliminary results of small size photothermal lesions induced on mice liver tissues. The morphology of the resulting lesions shows that optical fiber microheaters may render useful for delivering highly localized heat for photothermal therapy.

RESUMEN

Mechanical characterization of tissue is an important but complex task. We demonstrate the simultaneous use of Mueller matrix imaging (MMI), enhanced backscattering (EBS) and digital image correlation (DIC) in a bovine pericardium (BP) tensile test. The interest in BP relies on its wide use as valve replacement and biological patch. We show that the mean free path (MFP), obtained through EBS measurements, can be used as an indicator of the anisotropy of the fiber ensemble. Our results further show a good correlation between retardance images and displacement vector fields, which are intrinsically related with the fiber interaction within the tissue.

RESUMEN

We demonstrate an optopneumatic piston based on glass capillaries, a mixture of PDMS-carbon nanopowder, silicone and mineral oil. The fabrication method is based on wire coating techniques and surface tension-driven instabilities, and allows for the assembly of several pistons from a single batch production. By coupling the photothermal response of the PDMS-carbon mixture with optical excitation via an optical fiber, we demonstrate that the piston can work either as a valve or as a reciprocal actuator. The death volume of the pistons was between 0.02 and 1.56 µL and the maximum working frequency was around 1 Hz. Analysis of the motion during the expansion/contraction of the piston shows that this machine can be described by a phenomenological equation analogous to the Kelvin-Voight model used in viscoelasticity, having elastic and viscous components.

RESUMEN

We present a new all-optical fiber-referencing scheme for intensity-modulated sensors. It consists of a closed loop traversed by sensing and reference optical signals in opposite directions. With the proposed scheme the noise induced by power fluctuations of the optical source and mechanical perturbations can be greatly reduced. We experimentally demonstrate the efficiency of the scheme and discuss its use in a sensor array.