RESUMEN
OBJECTIVES: This study measured the transmission of light in the 'violet' (350≤λ≤425nm) and 'blue' (425<λ≤550nm) spectral ranges from a polywave(®) LED curing light through different thicknesses of four commercial, resin-based composites (RBCs). MATERIAL AND METHODS: Samples of conventional layered RBCs (Tetric EvoCeram A2, Filtek Supreme Ultra A2B), and bulk-curing resins (Tetric EvoCeram Bulk Fill IVA, and SureFil SDR Flow U) were prepared. Three samples of each RBC were made at thicknesses of 0.1, 0.7, 1, 2, and 4-mm. The uncured RBC specimens were affixed at the entrance aperture of a 6-inch integrating sphere and light-cured once for 20s using a polywave(®) LED curing light (Bluephase G2) on its high power setting. The spectral radiant power transmitted through each RBC in the 'violet' and 'blue' regions was measured using a fiberoptic spectrometer. RESULTS: As RBC thickness increased, an exponential attenuation of transmitted light was measured (R(2)>0.98). Attenuation was greater for the 'violet' than for the 'blue' spectral regions. At the light tip, the violet light component represented 15.4% of the light output. After passing through 4-mm of RBC, the violet light represented only between 1.2-3.1% of the transmitted light depending on the RBC. Depending on RBC, approximately 100mW from the Bluephase G2 was transmitted through 0.1-mm of RBC in the 'violet' range, falling at most to 11mW after passing through 2-mm of RBC, and to only 2mW at 4-mm depth. CONCLUSIONS: Increasing RBC thickness results in an exponential decrease in light transmission. This attenuation is RBC-dependent with shorter wavelengths (violet) attenuated to a greater extent than longer wavelengths (blue). CLINICAL RELEVANCE: Despite the increased translucency of bulk curing RBCs, spectral radiant power shorter than 425nm from a curing light is unlikely to be effective at a depth of 4-mm or more.
Asunto(s)
Materiales Dentales , Color , Resinas Compuestas , Luces de Curación Dental , Luz , Curación por Luz de Adhesivos Dentales , Ensayo de MaterialesRESUMEN
OBJECTIVES: For improved inter-study reproducibility and ultimately improved patient care, researchers and dentists need to know what electromagnetic radiation (light) is emitted from the light-curing unit (LCU) they are using and what is received by the resin. This information cannot be obtained from a dental radiometer, even though many studies have used a dental radiometer. METHODS: The light outputs from six LCUs (two QTH and four broad-spectrum LED units) were collected in real-time using an integrating sphere connected to a fiberoptic spectrometer during different light exposures. RESULTS: It was found that the spectral emissions were unique to each LCU, and there was no standardization in what was emitted on the various ramp (soft-start) settings. Relative to the normal use setting, using the ramp setting reduced the radiant energy (J) delivered from each LCU. For one of the four broad-spectrum LED LCUs, the spectral emissions in the violet range did not increase when the overall radiant power output was increased. In addition, this broad-spectrum LED LCU emitted no light from the violet LED chip for the first 5s and only emitted violet light when the ramp phase finished. CONCLUSIONS: A single irradiance value derived from a dental radiometer or from a laboratory grade power meter cannot adequately describe the output from the LCU. Manufacturers should provide more information about the light output from their LCUs. Ideally, future assessments and research publications that include resin photopolymerization should report the spectral radiant power delivered from the LCU throughout the entire exposure cycle.
Asunto(s)
Luces de Curación Dental , Resinas Compuestas/química , Materiales Dentales , Radiación Electromagnética , Luz , Ensayo de Materiales , Fotometría/métodos , Dosis de Radiación , Radiometría/instrumentación , Radiometría/métodos , Reproducibilidad de los Resultados , Semiconductores , Tecnología Odontológica/instrumentaciónRESUMEN
Recently, "budget" dental light-emitting diode (LED)-based light-curing units (LCUs) have become available over the Internet. These LCUs claim equal features and performance compared to LCUs from major manufacturers, but at a lower cost. This study examined radiant power, spectral emission, beam irradiance profiles, effective emission ratios, and the ability of LCUs to provide sustained output values during the lifetime of a single, fully charged battery. Three examples of each budget LCU were purchased over the Internet (KY-L029A and KY-L036A, Foshan Keyuan Medical Equipment Co, and the Woodpecker LED.B, Guilin Woodpecker Medical Instrument Co). Major dental manufacturers provided three models: Elipar S10 and Paradigm (3M ESPE) and the Bluephase G2 (Ivoclar Vivadent). Radiant power emissions were measured using a laboratory-grade thermopile system, and the spectral emission was captured using a spectroradiometer system. Irradiance profiles at the tip end were measured using a modified laser beam profiler, and the proportion of optical tip area that delivered in excess of 400 mW/cm(2) (termed the effective emission ratio) was displayed using calibrated beam profile images. Emitted power was monitored over sequential exposures from each LCU starting at a fully charged battery state. The results indicated that there was less than a 100-mW/cm(2) difference between manufacturer-stated average tip end irradiance and the measured output. All the budget lights had smaller optical tip areas, and two demonstrated lower effective emission ratios than did the units from the major manufacturers. The budget lights showed discontinuous values of irradiance over their tip ends. One unit delivered extremely high output levels near the center of the light tip. Two of the budget lights were unable to maintain sustained and stable light output as the battery charge decreased with use, whereas those lights from the major manufacturers all provided a sustained light output for at least 100 exposures as well as visual and audible indications that the units required recharging.
Asunto(s)
Luces de Curación Dental , Suministros de Energía Eléctrica , Resinas Compuestas , Ensayo de MaterialesRESUMEN
These studies were undertaken to examine effects of elevated glucose levels on glycolysis, sorbitol pathway activity, and the cytosolic redox state of NADH/NAD+ in isolated glomeruli. Blood-free glomeruli were isolated from kidneys of male, Sprague-Dawley rats using standard sieving techniques, then incubated for one hour at 37 degrees C, pH 7.4, pO2 approximately 500 torr, in Krebs bicarbonate/Hepes buffer containing 5 or 30 mM glucose. Elevated glucose levels increased glucose 6-phosphate, fructose 6-phosphate, total triose phosphates, lactate, the lactate/pyruvate ratio, sorbitol, and fructose, but did not affect sn-glycerol 3-phosphate, pyruvate, or myo-inositol levels. The more reduced glomerular cytosolic redox state (manifested by the tissue lactate/pyruvate ratio) induced by 30 mM glucose was completely abrogated by aldose reductase inhibitors added to the diet two to seven days prior to glomerular isolation. These observations, coupled with evidence linking glucose- and diabetes-induced glomerular dysfunction to increased sorbitol pathway metabolism, support the hypothesis that metabolic imbalances associated with a more reduced ratio of cytosolic NADH/NAD+ (resulting from increased glucose metabolism via the sorbitol pathway) play an important role in mediating glucose- and diabetes-induced glomerular dysfunction.