RESUMEN
The rotation of the maxillary molars is considered important in the orthodontic treatment of malocclusions. In this study, a computer analysis program was developed to examine the rotations of maxillary molars, mandibular molars, and maxillary first premolars in casts of permanent dentitions with acceptable occlusions. Ninety-three sets of untreated 'acceptable occlusion' models from the collection of the Foundation for Orthodontic Research (FOR) were scanned on a flat bed scanner. The images were analysed using custom software. Measurements were made by relating maxillary first permanent molars to the midline, archform, opposite canine, and mandibular first permanent molars. The mandibular first molars and maxillary first premolars were also analysed and their rotations measured. The mean rotations of the maxillary first molars, measured as the angle between a line joining the tips of the buccal cusps and a line tangent to the appropriate archwire form (from Ricketts' Pentamorphic Arches) at the first molars, were 0.59 and -0.72 degree (positive values represent mesio-lingual rotations) for the right and left, respectively. For the mandibular molars, these means were 6.34 and 8.40 degrees, respectively. The mean differences in rotation between buccal cusp tips of maxillary and mandibular first molars in occlusion were 5.75 and 9.12 degrees for the right and left, respectively, with the mandibular being more mesio-lingually rotated. The differences between left and right were significant for all measurements. The present study brings into question the suitability of our present "straight wire" prescriptions in producing similar occlusions. It also suggests that scanning models for computer analysis may be a practical and precise way to measure similar rotations in untreated normal and treated occlusions.
Asunto(s)
Diente Premolar , Oclusión Dental , Diente Molar , Ortodoncia Correctiva/métodos , Análisis de Varianza , Diagnóstico por Computador/métodos , Diagnóstico por Computador/estadística & datos numéricos , Humanos , Maloclusión/diagnóstico , Maloclusión/terapia , Mandíbula , Maxilar , Modelos Dentales , Ortodoncia Correctiva/estadística & datos numéricos , Valores de Referencia , Rotación , Programas Informáticos , Estadísticas no ParamétricasRESUMEN
To evaluate the health effects of air pollutants on the respiratory tract, it is critical to determine the regional deposition of inhaled aerosols. Information on deposition of larger particles (greater than 0.2 microns) in the nasal passages of laboratory animals is available; the deposition fraction increases with increasing particle size. However, little deposition information is available for ultrafine particles of less than 0.2 microns. Three clear, plastic molds (models) of the nasal passages of F344/N rats, prepared from metal replica casts were used in these studies. Total deposition of ultrafine aerosols in the casts was determined by using a unidirectional flow system. The pressure drops measured in the casts were a function of flow rate to the power of 1.4-1.6, indicating that flow through the nasal passages has nonlaminar components. Deposition data were obtained by using monodisperse sodium chloride aerosols with particle sizes ranging from 0.2 to 0.005 microns, at inspiratory and expiratory flow rates of 200 to 600 ml/min. Similar deposition data were obtained for two of the casts studied. Deposition efficiency was greatest for the smallest particles, and decreased with increasing particle size and flow rate. At an inspiratory flow rate of 400 ml/min, which is comparable to the mean respiratory flow of an adult male F344 rat with a respiratory minute volume of 200 ml, deposition efficiencies reached 40 and 70% for 0.01- and 0.005-microns particles, respectively. These studies demonstrated that turbulent diffusional deposition was the dominant mechanism for uptake of ultrafine particles by the nasal passages.