RESUMEN

This review presents a critical examination of the interface for coupling high performance liquid chromatography (HPLC) with Fourier transform infrared spectrometry (FTIR) since 2010. This coupling offers a robust analytical approach characterized by exceptional chemical specificity and the capacity to analyze complex multi-component mixtures qualitatively and quantitatively with high sensitivity, particularly in low limit of detection ranges. This coupling enables the identification of individual components of a mixture by IR after their separation by HPLC, although challenges arise from the potential distortion of infrared spectra by mobile phase components. Addressing this issue necessitates the implementation of suitable interfaces, such as flow cells or off-line indirect measurement methods like hot inert gas streams or ultrasonic nebulizers. The key parameters influencing the coupling of HPLC-FTIR include the solvent elimination methods, mode of FTIR technique, and IR background for accurate analyte identification. Moreover, the composition of the mobile phase and the utilization of buffer solutions in the HPLC mobile phase profoundly impact analyte identification by FTIR.

RESUMEN

This work presents a "green" analytical method developed for the determination of potentially toxic metals such as aluminium, barium and chromium in solid plastics samples using the slurry sampling technique in conjunction with electrothermal atomic absorption spectrometry. The development of the slurry sampling technique in conjunction with electrothermal atomic absorption spectrometry entailed optimisation of the measuring conditions, which included optimisation of the temperature programme, selection of an appropriate liquid medium for slurry preparation, optimisation of the concentration and volume of the liquid medium and optimisation of the mass of the solid plastics sample. The following conditions were determined: the optimal pyrolysis temperature for aluminium, barium and chromium was in the range of 1300 °C to 1700 °C and the optimal atomisation temperature was in the range of 2100 °C to 2400 °C. The optimal liquid media for solid plastics samples were H2O, 0.2% (v/v) HNO3 and 0.2% (v/v) HCl. The optimal volume of liquid medium was in the range from 5 to 15 mL and the mass of the solid plastics samples was in the range from 30 to 100 mg. The limit of detection and limit of quantification were estimated as 0.06-0.52 ng g-1 and 0.22-1.69 ng g-1 for aluminium, 0.11-0.94 ng g-1 and 0.37-3.14 ng g-1 for barium and 0.07-0.31 ng g-1 and 0.25-1.04 ng g-1 for chromium. Relative standard deviation was below 5% for all plastic samples analysed. Based on the established validation parameters, the slurry sampling technique in conjunction with electrothermal atomic absorption spectrometry represents a viable technique for metal analysis of a variety of plastic materials. The concentrations of analytes in individual solid plastic samples were in the range of 1.36 ± 0.06 µg g-1 to 22.65 ± 0.66 µg g-1 for aluminium, 1.13 ± 0.03 µg g-1 to 6.01 ± 0.22 µg g-1 for barium and 0.60 ± 0.03 µg g-1 to 10.48 ± 0.46 µg g-1 for chromium.

RESUMEN

Cloud-point extraction (CPE) is a pre-treatment technique for the extraction and preconcentration of different chemical compounds, such as metal ions, pesticides, drugs, phenols, vitamins etc., from various samples. CPE is based on the phenomenon of two phases (micellar and aqueous) forming after the heating of an aqueous isotropic solution of a non-ionic or zwitterionic surfactant above the cloud-point temperature. If analytes are added to the surfactant solution under suitable conditions, they should be extracted into the micellar phase, also called the surfactant-rich phase. Recently, the traditional CPE procedure is being increasingly replaced by improved CPE procedures. In this study, recent advances in CPE over the last three years (2020 - 2022), including the application of various innovative approaches, are reviewed. In addition to the basic principle of CPE, alternative extraction media in CPE, CPE supported by various auxiliary energies, a different modified CPE procedure and the use nanomaterials and solid-phase extraction in combination with CPE are presented and discussed. Finally, some future trends for improved CPE are presented.

Asunto(s)

RESUMEN

In the present work, nanotwin structured TiO2 nanotube (TNT) layers are prepared by the electrochemical anodization technique to form the anatase phase and by surface modification via spin-coating of Ce and V precursors to form Ce-TNT and V-TNT, respectively. The surface and cross-sectional images by SEM revealed that the nanotubes have an average diameter of ∼130 nm and a length of ∼14 µm. In addition, the TEM images revealed the nanotwin structures of the nanotubes, especially the anatase (001) and (112) twin surfaces, that increase the transport of photogenerated charges. The photoinduced degradation of caffeine (CAF) by TNT, Ce-TNT, and V-TNT led to a degradation extent of 16%, 26% and 33%, respectively, whereas it increased to 26%, 38%, and 46% in the presence of H2O2, owing to the involvement of Fenton-based processes (in addition to photocatalysis). The effect of the Fenton-based processes accounts for about 10% of the total degradation extent of CAF. Finally, the mechanism of the photoinduced degradation of CAF was investigated. The main oxidative species were the hydroxyl radicals, and the better efficiency of V-TNT over Ce-TNT and TNT was ascribed to its negative surface, thus improving the interactions with CAF.

Asunto(s)

RESUMEN

A new analytical procedure was developed for the determination of lead in human placental tissue by direct ultrasonic slurry sampling combined with electrothermal atomic absorption spectrometry (SS-ET AAS). Samples of dried and crushed placental tissue were mixed with 10 mL of 0.20% (v/v) HNO3 and homogenised. The slurries were then transferred to autosampler cups where they were sonicated using an ultrasonic probe prior to injection into a graphite tube with an L'vov platform. The effects of several chemical modifiers, including Mg(NO3)2, Pd(NO3)2, and NH4H2PO4, were investigated for the stabilisation of lead during thermal pre-treatment. Lead in the slurries was effectively stabilised up to 1200 °C with the Pd(NO3)2 modifier providing the best results with complete atomisation at 1900 °C. H2O2 was used as a chemical modifier; dilute HNO3 and HCl were examined as slurry media. The limit of detection and the limit of quantification for lead obtained under optimised conditions were 0.17 µg g-1 and 0.56 µg g-1, respectively. The relative standard deviation estimated from twenty replicate measurements of spike solution at a concentration of 50.00 µg L-1 for lead was 1.51%. The accuracy of the method was confirmed by analysis of the standard reference material BCR 185R "Bovine Liver". The proposed technique is simple, sensitive and environmentally friendly, and the risk of contamination is low. The method was applied to lead determination in real samples of human placental tissue. The 14 samples were taken just after delivery at the Gynaecology and Obstetrics Department of the Faculty Hospital with Outpatients Clinic in Bratislava over the course of 2019.

Asunto(s)

RESUMEN

Cytostatic compounds are an important group of micro-pollutants since they are used to kill cells or stop cell division. For this reason, they are also considered mutagenic. Several cytostatic compounds have been detected in hospital effluents, in the influents and effluents of wastewater treatment plants and even in river water. However, their detection in solid matrices is very scarce. In this work, we have developed a new procedure based on microwave-assisted extraction (MAE) for the extraction of cytostatic compounds from sludge and sediment before determination by ultra-high-performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS). To develop this procedure, we have chosen a group of eight widely used cytostatic compounds and carried out a systematic experimental design to optimize the extraction conditions. Under these optimal conditions, the studied cytostatic compounds are extracted with good sensitivity, with recoveries ranging from 65 to 122% in sludge and recoveries varying between 49 and 109% in sediment, with the exception of etoposide, which has a lower recovery from these types of samples. The limits of detection were from 0.42 to 79.8 ng g-1 in sludge and from 0.10 to 87.5 ng g-1 in sediment. Intraday and interday relative standard deviations (RSDs) were below 15% and 18%, respectively, in both matrices at the tested concentrations. The total procedure was applied to samples of sludge taken from the main wastewater treatment plant (WWTP) of the island of Gran Canaria (Spain) and for sediment samples obtained close to the marine outfalls of different wastewater treatment plants for the same island. Graphical abstract.

Asunto(s)

RESUMEN

This work is focused on separation and determination of amygdalin and its unnatural form neoamygdalin in natural food supplements. Reversed-phase high-performance liquid chromatography with a high-stability silica-based column with C18 functional group has been used for solving this problem. The effect of the mobile phase composition as well as the column temperature on the separation of the amygdalin epimers has been investigated. Isocratic elution using a mobile phase composed of 0.05% aqueous formic acid and acetonitrile achieved the required separation within 17 min. Under optimum chromatographic conditions, the developed method was validated and was applied for the determination of amygdalin epimers in natural food supplements containing apricot or peach kernels. A simple extraction method using methanol as an extractant supported by an ultrasonic bath was used with recovery in the range of 94.8% to 104.3%. The limit of detection and limit of quantification values for R-amygdalin were 0.13 mg/L and 0.40 mg/L, respectively. The developed method proved to be precise with the intra-day and inter-day relative standard deviation values less than 2.23%.

Asunto(s)

RESUMEN

A case of suspected acute and lethal intoxication caused by colchicine has been reported. The woman was hospitalized after her suspicion of suicidal poisoning by a rare autumn crocus (Colchicum autumnale). Suspected colchicine poisoning was confirmed using a novel UHPLC method with a modern reversed-phase stationary phase with a sub 2-micron superficial porous particle size combined with a QTOF mass spectrometer. Sample preparation procedure included the addition of propiverine as internal standard, protein precipitation using methanol and solid phase extraction. High-resolution MS only and targeted MS/MS modes are reported for the qualitative analysis and screening of other potential drugs of abuse in blood samples. All Ion MS mode was used for quantitative determination of colchicine afterward. The concentration of colchicine in the blood sample was approximately 41 ng/mL, and more than 200 µg/mL of the plant extract used for the suicide.

Asunto(s)

RESUMEN

Tadalafil is used for the treatment of erectile dysfunction. Its related patents expired in 2016, and so related generic drug production is predicted to be increased. This work is focused on developing a fast ultra-high-performance liquid chromatography with diode array detection and/or mass spectrometry detection for the separation and determination of tadalafil and its impurities in pharmaceutical samples. A modern reversed-phase stationary phase with sub-2 µm particle size, Zorbax StableBond Rapid Resolution High Definition with octylsilane chemically bonded phase to totally porous silica particles, was used for the solving this problem. Column temperature was set at 40 ± 0.1°C. A mobile phase consisting of acetonitrile and aqueous solution of 0.1% (v/v) trifluoroacetic acid for diode array detection detection and 0.05% (v/v) formic acid, both running at a flow rate of 0.62 mL/min, were used to achieve the required separation of all components within a 5 min run. The limit of detection was 3.5 µg/L and the limit of quantification was 10.0 µg/L for the method for both UV and MS detectors. Accurate mass spectra of tadalafil's related impurities are shown for advanced confirmation. The method is directly transferable to routine analysis of tadalafil in pharmaceutical and control laboratories.

Asunto(s)

RESUMEN

The influence of the mobile phase and temperature, on the retention behavior of seven aliphatic acids (pyruvic, gluconic, 2-oxoglutaric, tartaric, malic, oxalic, and citric acid) in hydrophilic interaction liquid chromatography on zwitterionic stationary phases with sulfobetaine and phosphorylcholine ligands is investigated. In agreement with the van't Hoff model, most acids show linear ln k versus 1/T plots. However, the retention of structurally symmetrical oxalic and tartaric dicarboxylic acids is almost independent of temperature, or slightly increases at rising temperature. The experimental parameters of the van't Hoff plots suggest positive entropic contributions to the retention of these symmetrical acids, possibly connected with changes in molecular symmetry on their adsorption. The type of the zwitterionic stationary phase and the mobile phase composition (the molar concentration of acetate buffer and the volume fraction of acetonitrile) affect the retention and the selectivity of the separation of the acids.

RESUMEN

Permanent need to understand nature, structure and properties of humic substances influences also separation methods that are in a wide scope used for fractionation, characterization and analysis of humic substances (HS). At the first glance techniques based on size-exclusion phenomena are the most useful and utilized for relating elution data to the molecular mass distribution of HS, however, with some limitations and exceptions, respectively, in the structural investigation of HS. The second most abundant separation mechanism is reversed-phase based on weak hydrophobic interactions beneficially combined with the step gradients inducing distinct features in rather featureless analytical signal of HS. Relatively great effort is invested to the developments of immobilized-metal affinity chromatography mimicking chelate-forming properties of HS as ligands in the environment. Surprisingly, relatively less attention is given to the ion-ion interactions based ion-exchange chromatography of HS. Chromatographic separation methods play also an important role in the examination of interactions of HS with pesticides. They allow us to determine binding constants and the other data necessary to predict the mobility of chemical pollutants in the environment. HS is frequently adversely acting in analytical procedures as interfering substance, so more detailed information is desired on manifestation of its numerous properties in analytical procedures. The article topic is covered by the review emphasizing advances in the field done in the period of last 10 years from 2000 till 2010.

Asunto(s)

RESUMEN

The idea of utilization of one hydraulic line of a common commercial HPLC pump for direct on-column sample pumping injection of large sample volumes, 20 mL, was further investigated with the aim to develop multicomponent pesticides trace residues HPLC method in gram soil samples. Target pesticides group involve asulam, atrazine, 2,4-D, PCA, propazine, simazine, 4-chloro-2-methylphenoxyacetic acid, 2-(4-chloro-2-tolyloxy) propionic acid, chlortoluron, metoxuron, epoxiconazole. The results proved the applicability of this approach in experiments with mixtures of analytes at low ng/mL levels. Analysis of 20 mL of soil leachates and extracts of fortified soil samples containing these pesticides at the 10-50 ng/g level (in dry soil) revealed good figures of merit, also in the presence of large excess of humics. LODs achieved by detection at 220 nm evaluated from calibration runs of spiked soil extracts by Hubaux et al. method ranged from 5-12 ng per injected volume. For 20 mL large volume injection it represents 0.25-0.6 ng/mL of diluted soil extract, or 2.5-6 ng/mL of crude extract, or 6-5 ng/g dry soil. Recoveries of pesticides at concentration levels approaching half of maximum allowable concentration of pesticides in soil (100 ng/g) ranged from 85 to 98% with acceptable reproducibility, except asulam and metoxuron.

Asunto(s)

RESUMEN

A simple and fast analytical method was developed for the determination of benzimidazole fungicides (benomyl, carbendazim, thiabendazole, and fuberidazole) in soil samples. The analytes were extracted from the soil samples by means of conventional microwave-assisted extraction, using the non-ionic surfactants polyoxyethylene 10 lauryl ether (POLE) and oligoethylene glycol monooalkyl ether (Genapol X-080) as extractants. Determinations were made by using liquid chromatography with direct fluorescence detection. The use of an analytical column Symmetry C-18 offered short retention times of analytes without the need of any pH regulators with mobile phase methanol-water (50 + 50, v/v). The best results were obtained using 5% (v/v) POLE as extractant with recoveries of the fungicides in spiked soil samples between 71 and 105%. The results were compared with those obtained when Soxhlet extraction was applied to the same soil samples.

Asunto(s)

RESUMEN

A well established method of direct injection of larger than conventional sample volumes ranging from 0.1 mL to 10 mL in HPLC is the injection valve method in which a loop of tubing is totally or partially filled with sample. Recent HPLC pumps have a flow-rate setting accuracy of +/- 1-2% over a flow-rate range from 0.1 mL/min to 10 mL/min and the flow stability is 0.2% or less. Quarternary low pressure gradient pumps are widely available and used, but all their hydraulic lines are seldom utilised. The idea of using one line of a common commercial HPLC quaternary low-pressure pump for direct on-column injection (pumping) of large sample volumes ranging from 1 mL to 100 mL was tested. This approach was evaluated during practical work on the development of an RP-HPLC method of determination of residual atrazine and hydroxyatrazine. In lysimetric environmental experiments hydroxyatrazine was formed in situ in a soil column by hydrolysis of atrazine. The results proved the applicability of this approach not only in experiments with model mixtures of analytes at microg/L levels in solutions. Analysis of 20 mL of soil leachates and extracts of soil samples containing atrazine and hydroxyatrazine at the 10 microg/kg level (in dry soil) revealed that good figures-of-merit were preserved, even in the presence of a large excess of humic substances.

Asunto(s)

RESUMEN

Selected trace transition metal ions have been determined in an FIA/HPLC hyphenated system using on-line preconcentration on cellulose functionalised sorbent Cellex P. For HPLC separation ion-pair chromatography was employed with spectrophotometric detection at 510 nm using post-column derivatisation with PAR. Favourable kinetic conditions of sorption and elution as well as optimisation of hyphenated system allowed to obtain detection limits at sub-microgL(-1) level at 25 min preconcentration time. The developed method was employed for determination of Co(II), Ni(II), Cd(II) and Mn(II) in river water with reasonable agreement of obtained results with electrothermal AAS determination.

Asunto(s)