RESUMEN
Cerium oxide powders are widely used and are of fundamental importance in catalytic pollution control and energy production due to the unique chemical properties of CeO2. Processing steps involved in catalyst preparation, such as high-temperature calcination or mechanical milling processes, can alter the morphological and chemical properties of ceria, heavily affecting its final properties. Here, we focus on the tuning of CeO2 nanopowder properties by mild- and high-energy milling processes, as the mechanochemical synthesis is gaining increasing attention as a green synthesis method for catalyst production. The textural and redox properties were analyzed by an array of techniques to follow the aggregation and comminution mechanisms induced by mechanical stresses, which are more prominent under high-energy conditions but strongly depend on the starting properties of the ceria powders. Simultaneously, the evolution of surface defects and chemical properties was followed by Raman spectroscopy and H2 reduction tests, ultimately revealing a trade-off effect between structural and redox properties induced by the mechanochemical action. The mild-energy process appears to induce the largest enhancement in surface properties while maintaining bulk properties of the starting materials, hence confirming its effectiveness for its exploitation in catalysis.
RESUMEN
Commercial rutile TiO2 particles capped with Al2O3 and ZrO2 layers, which are widely used in white pigments, can serve as a starting material for the fabrication of visible light-responsive photocatalysts toward gas-phase NO oxidation. The as-received TiO2 with iron impurities exhibited reduced photocatalytic activity, and the activity was boosted by the deposition of additional iron comparable in quantity to the intrinsic iron impurity level. Analyses using X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectroscopy, and low-energy ion scattering spectroscopy revealed that the deposited iron and intrinsic impurity iron are dissimilar in terms of location, oxidation states, and interaction with TiO2. This suggests that tracking the structure and impurity levels of photocatalyst elements can be crucial for understanding structure-activity relationships of real catalysts.
RESUMEN
Surface-clean Au nanoparticles (NPs) confined in films of ionic liquids (ILs) can be easily fabricated by sputtering deposition. A silicon wafer coated with films of both hydrophobic (bis((trifluoromethyl)sulfonyl)amide, NTf2-) and hydrophilic (tetrafluoroborate, BF4-) imidazolium-based ILs forms an 'ionic carpet-like' structure that can be easily decorated with Au NPs of 5.1 and 6.5 nm mean diameter, respectively. The depth profile distribution of the Au NPs depends on the arrangement of the IL, which is controlled mainly by the anion volume. Higher concentrations of Au NPs are found closer to the IL surface for the system containing a larger anion (NTf2) whereas Au NPs are located deeper in the IL for the system containing a smaller anion (BF4). The Au NPs are well distributed over the IL/Si support and are strictly confined in a single layer of the IL. This method is among the most simple and versatile for the generation of liquid layers containing surface-clean, stable and confined Au NPs.
RESUMEN
Low-energy ion scattering (LEIS) is known for its extreme surface sensitivity, as it yields a quantitative analysis of the outermost surface as well as highly resolved in-depth information for ultrathin surface layers. Hence, it could have been generally considered to be a suitable technique for the analysis of graphene samples. However, due to the low scattering cross section for light elements such as carbon, LEIS has not become a common technique for the characterization of graphene. In the present study we use a high-sensitivity LEIS instrument with parallel energy analysis for the characterization of CVD graphene transferred to thermal silica/silicon substrates. Thanks to its high sensitivity and the exceptional depth resolution typical of LEIS, the graphene layer closure was verified, and different kinds of contaminants were detected, quantified, and localized within the graphene structure. Utilizing the extraordinarily strong neutralization of helium by carbon atoms in graphene, LEIS experiments performed at several primary ion energies permit us to distinguish carbon in graphene from that in nongraphitic forms (e.g., the remains of a resist). Furthermore, metal impurities such as Fe, Sn, and Na located at the graphene-silica interface (intercalated) are detected, and the coverages of Fe and Sn are determined. Hence, high-resolution LEIS is capable of both checking the purity of graphene surfaces and detecting impurities incorporated into graphene layers or their interfaces. Thus, it is a suitable method for monitoring the quality of the whole fabrication process of graphene, including its transfer on various substrates.
RESUMEN
High-sensitivity low-energy ion scattering (HS-LEIS) analysis was used to elucidate the outermost layer of both functionalized and non-functionalized imidazolium ionic liquids (ILs). The IL outermost layer is composed of all atoms of both cations and anions. The HS-LEIS analyses also allow for quantitative measurement of the thickness of IL overlayers on Au nanoparticles prepared by sputter deposition, which was shown to be a monolayer of ions, as predicted by density functional theory calculations.