RESUMEN
Materials and surfaces developed for dental implants need to withstand degradation processes that take place in the oral cavity. Therefore, the aim of the study was to develop and evaluate the topographical, mechanical, chemical, electrochemical and biological properties of Ti-xZr alloys (xâ¯=â¯5, 10, and 15â¯wt%) with two surface features (machined and double acid etched). Commercially pure titanium (cpTi) and Ti-6Al-4V alloy were used as controls. Surface characterization was performed using dispersive energy spectroscopy, X-ray diffraction, scanning electron microscopy, atomic force microscopy, profilometry and surface energy. The mechanical properties were assessed using Vickers microhardness, elastic modulus and stiffness. The electrochemical behavior analysis was conducted in a body fluid solution (pHâ¯7.4). In addition, MC3T3-E1 cells were used to determine the impact of material and surface treatment on cell morphology by SEM analysis. Data were analyzed by two-way ANOVA and Bonferroni test (αâ¯=â¯0.05). Ti-Zr alloys showed lower surface roughness, elastic modulus and stiffness, as well as higher hardness and surface energy when compared to cpTi. Ti-Zr system increased the polarization resistance values and significantly decreased the capacitance, corrosion current density (icorr), and passivation current density (ipass) values. The acid treatment increased the resistance and corrosion potential of the oxide layer. SEM data analysis demonstrated that Ti-Zr alloys displayed normal cell attachment/spreading and slightly changed cell morphology in the double etched surface. In conclusion, Zr addition and surface treatment altered surface, mechanical, biological and electrochemical properties of Ti material.
Asunto(s)
Aleaciones/química , Aleaciones Dentales/química , Implantes Dentales , Análisis de Varianza , Animales , Materiales Biocompatibles/química , Línea Celular , Corrosión , Electroquímica , RatonesRESUMEN
The Ti-15Mo alloy has its mechanical properties strongly altered by heat treatments and by addition of interstitial elements, such as, oxygen, for example. In this sense, the objective of this paper is to analyze the effect of the introduction of oxygen in selected mechanical properties and the biocompatibility of Ti-15Mo alloy. The samples used in this study were prepared by arc-melting and characterized by density measurements, X-ray diffraction, scanning electron microscopy, microhardness, modulus of elasticity, and biocompatibility tests. Hardness measurements were shown to be sensitive to concentration of oxygen. The modulus results showed interstitial influence in value; this was verified under several conditions to which the samples were exposed. Cytotoxicity tests conducted in vitro showed that the various processing conditions did not alter the biocompatibility of the material.
RESUMEN
The mechanical properties of Ti alloys are changed significantly with the addition of interstitial elements, such as oxygen. Because oxygen is a strong stabilizer of the α phase and has an effect on hardening in a solid solution, it has aroused great interest in the biomedical area. In this paper, Ti-Zr alloys were subjected to a doping process with small amounts of oxygen. The influence of interstitial oxygen in the structure, microstructure and some selected mechanical properties of interest for use as biomaterial and biocompatibility of the alloys were analyzed. The results showed that in the range of 0.02 wt% to 0.04 wt%, oxygen has no influence on the structure, microstructure or biocompatibility of the studied alloys, but causes hardening of the alloys, increasing the values of the microhardness and causing variation in the elasticity modulus values.
RESUMEN
OBJECTIVE: This study evaluated the glass transition temperature (Tg) and degree of conversion (DC) of a light-cured (Fill Magic) versus a chemically cured (Concise) orthodontic composite. MATERIAL AND METHODS: Anelastic relaxation spectroscopy was used for the first time to determine the Tg of a dental composite, while the DC was evaluated by infrared spectroscopy. The light-cured composite specimens were irradiated with a commercial LED light-curing unit using different exposure times (40, 90 and 120 s). RESULTS: Fill Magic presented lower Tg than Concise (35-84 masculineC versus 135 masculineC), but reached a higher DC. CONCLUSIONS: The results of this study suggest that Fill Magic has lower Tg than Concise due to its higher organic phase content, and that when this light-cured composite is used to bond orthodontic brackets, a minimum energy density of 7.8 J/cm(2) is necessary to reach adequate conversion level and obtain satisfactory adhesion.
Asunto(s)
Resinas Compuestas/química , Vidrio/química , Soportes Ortodóncicos , Cementos de Resina/química , Temperatura de Transición , Bisfenol A Glicidil Metacrilato/química , Resinas Compuestas/efectos de la radiación , Luces de Curación Dental/clasificación , Módulo de Elasticidad , Transferencia de Energía , Fricción , Vidrio/efectos de la radiación , Calor , Humanos , Luz , Ensayo de Materiales , Polímeros/química , Cementos de Resina/efectos de la radiación , Espectroscopía Infrarroja por Transformada de Fourier , Análisis Espectral , Factores de TiempoRESUMEN
OBJECTIVE: This study evaluated the glass transition temperature (Tg) and degree of conversion (DC) of a light-cured (Fill Magic) versus a chemically cured (Concise) orthodontic composite. MATERIAL AND METHODS: Anelastic relaxation spectroscopy was used for the first time to determine the Tg of a dental composite, while the DC was evaluated by infrared spectroscopy. The light-cured composite specimens were irradiated with a commercial LED light-curing unit using different exposure times (40, 90 and 120 s). RESULTS: Fill Magic presented lower Tg than Concise (35-84ºC versus 135ºC), but reached a higher DC. CONCLUSIONS: The results of this study suggest that Fill Magic has lower Tg than Concise due to its higher organic phase content, and that when this light-cured composite is used to bond orthodontic brackets, a minimum energy density of 7.8 J/cm² is necessary to reach adequate conversion level and obtain satisfactory adhesion.