RESUMEN

This article presents the design of a 2-bit dual-band switchable terahertz absorber using a stacked combination of graphene and vanadium dioxide (VO2) metamaterials. For the first time, the proposed absorber design offers four switchable states by controlling the conductivity of graphene and VO2 metamaterial layers. The lower absorption band is produced by the graphene metamaterial, whereas the upper band is implemented by the VO2 metamaterial pattern. The structure shows two absorption bands (State 11) at 0.745-0.775 THz and 2.3-5.63 THz, when the Fermi graphene level of graphene is 0.2 eV and the VO2 is in the metallic phase. The lower absorption band is turned off, while keeping the upper band (State 01), when the graphene Fermi level is 0 eV and the VO2 layer is in the metallic phase. The upper absorption band is turned off, while preserving the lower absorption band (State 10) by switching the VO2 into the insulator phase and keeping the graphene Fermi level at 0.2 eV. Finally, both of the absorption bands are turned off by setting the graphene Fermi level to 0 eV and switching the VO2 into the insulating phase. Equivalent circuit modelling analysis and full-wave electromagnetic simulations are used to explain the operation principle of the proposed absorber. Very good agreement is obtained between the theoretical analysis and the simulations confirming the presented design principle for the 2-bit switchable absorber.

RESUMEN

In this paper, a very high sensitivity microwave-based planar microfluidic sensor is presented. Sensitivity enhancement is achieved and described theoretically and experimentally by eliminating any extra parasitic capacitance not contributing to the sensing mechanism. The sensor consists of a microstrip transmission line loaded with a series connected shunt LC resonator. A microfluidic channel is attached to the area of the highest electric field concentration. The electric field distribution and, therefore, the resonance characteristics are modified by applying microfluidic dielectric samples to the sensing area. The sensor performance and working principle are described through a circuit model analysis. A device prototype is fabricated, and experimental measurements using water/ethanol and water/methanol solutions are presented for validation of the sensing mathematical model.

Asunto(s)

RESUMEN

Leidenfrost droplets can be considered as soft engines capable of directly transforming heat into mechanical energy. Despite remarkable advancements in understanding the propulsion of Leidenfrost droplets on asymmetric structures, the complex dynamics of droplets in enclosed structures is not fully understood. To address this fundamental gap, we investigated the dynamics of Leidenfrost droplets restricted by metal disks. The disk alters the accumulation and release of the vapour generated by the droplet, and substantially changes its dynamic characteristics. Our experiments reveal the formation of oscillating multi-lobed structures when restricting the droplet within a disk. In comparison, patterning offset radial grooves on the surface of the disk rectifies the vapour flow and facilitates the self-propulsion of the droplet along the edge of the disk. Our work offers opportunities for developing soft and short-living actuators, which can operate at high temperatures.

RESUMEN

A differential microwave permittivity sensor and comparator is designed using a microstrip transmission line loaded with a magnetic-LC resonator. The microstrip transmission line is aligned with the electric wall of the resonator. The sensor shows a single transmission zero, when it is unloaded or loaded symmetrically on both halves. A second notch appears in the transmission response by asymmetrical dielectric loading on the two halves of the device. The frequency splitting is used to characterize the dielectric properties of the samples under test. The sensitivity of the sensor is enhanced by removing the mutual coupling between the two halves of the magnetic-LC resonator using a metallic wall. The sensors' operation principle is explained through a circuit model analysis. A prototype of the designed sensor is fabricated and measurements are used for validation of the sensing concept. The sensor can be used for determination of the dielectric properties in solid materials or detecting defects and impurities in solid materials through a comparative measurement with a reference sample.

RESUMEN

Here, we demonstrate a modular, reconfigurable, and self-sufficient convective heat exchanger for regulation of temperature in microfluidic systems. The heat exchanger consists of polymer tubes wrapped around a plastic pole and fully embedded in an elastomer block, which can be easily mounted onto the microfluidic structure. It is compatible with various microfluidic geometries and materials. Miniaturized, battery-powered piezoelectric pumps are utilized to drive the heat carrying liquid through the heat exchanger at desired flow rates and temperatures. Customized temperature profiles can be generated by changing the configuration of the heat exchanger with respect to the microfluidic structure. Tailored dynamic temperature profiles can be generated by changing the temperature of the heat carrying liquid in successive cycles. This feature is used to study the calcium signaling of endothelial cells under successive temperature cycles of 24 to 37 °C. The versatility, simplicity, and self-sufficiency of the heat exchanger makes it suitable for various microfluidic based cellular assays.

RESUMEN

Here, we demonstrate a multilayered microfluidic system integrated with commercially available polymer tubes for controlling the temperature of the sample under various static and dynamic conditions. Highly controllable temperature profiles can be produced by modulating the flow rate or inlet temperature of the water passing through the tubes. Customised temperature gradients can be created across the length or width of a channel by mismatching the inlet temperature of the tubes. Temperature cycles can also be produced by repeatedly switching the tubes between hot and cold flasks. Proof-of-concept experiments demonstrate the utility of this system for studying the drug-induced calcium signaling of human monocytes under dynamic thermal conditions. The versatility and simplicity of our system provides opportunities for studying temperature-sensitive chemical, biochemical, and biological samples under various operating conditions.

RESUMEN

Orbital Angular Momentum (OAM), as a property of Electromagnetic (EM) fields has recently been proposed for Radio and Microwave communications. This paper investigates a new class of OAM radiation patterns for Radio and Microwave applications, namely, Quasi-OAM radiation patterns, induced by a proposed Quasi-Circular Array Antenna (QCA). Simulations and Experiments show that Quasi-OAM waves can be induced and preserved in the far-field using the proposed QCA apertures and configurations, demonstrating non-integer dominant OAM modes corresponding to l = +1 and l = -1 with a directional quasi intensity and rotational 2π phase profiles. The proposed method in this work significantly reduces aperture size and cost by using Quasi-Circular Arrays of N Q = 5 and N Q = 6 elements in lieu of conventional OAM circular aperture arrays with N = 8 elements.

RESUMEN

Generating customised temperature gradients in miniaturised flow-free liquid chambers is challenging due to the dominance of diffusion. Inducing internal flows in the form of vortices is an effective strategy for overcoming the limitations of diffusion in such environments. Vortices can be produced by applying pressure, temperature and electric potential gradients via miniaturised actuators. However, the difficulties associated with the fabrication, integration, maintenance and operation of such actuators hinder their utility. Here, we utilise liquid metal enabled pumps to induce vortices inside a miniaturised liquid chamber. The configuration and rotational velocity of these vortices can be controlled by tuning the polarity and frequency of the energising electrical signal. This allows creation of customised spatial temperature gradients inside the chamber. The absence of conventional moving elements in the pumps facilitates the rapid reconfiguration of vortices. This enables quick transition from one temperature profile to another, and creates customised spatiotemporal temperature gradients. This allows temperature oscillation from 35 to 62 °C at the hot spot, and from 25 to 27 °C at the centre of the vortex within 15 seconds. Our liquid metal enabled vortex generator can be fabricated, integrated and operated easily, and offers opportunities for studying thermo-responsive materials and biological samples.

RESUMEN

Strain sensors with high elastic limit and high sensitivity are required to meet the rising demand for wearable electronics. Here, we present the fabrication of highly sensitive strain sensors based on nanocomposites consisting of graphene aerogel (GA) and polydimethylsiloxane (PDMS), with the primary focus being to tune the sensitivity of the sensors by tailoring the cellular microstructure through controlling the manufacturing processes. The resultant nanocomposite sensors exhibit a high sensitivity with a gauge factor of up to approximately 61.3. Of significant importance is that the sensitivity of the strain sensors can be readily altered by changing the concentration of the precursor (i.e., an aqueous dispersion of graphene oxide) and the freezing temperature used to process the GA. The results reveal that these two parameters control the cell size and cell-wall thickness of the resultant GA, which may be correlated to the observed variations in the sensitivities of the strain sensors. The higher is the concentration of graphene oxide, then the lower is the sensitivity of the resultant nanocomposite strain sensor. Upon increasing the freezing temperature from -196 to -20 °C, the sensitivity increases and reaches a maximum value of 61.3 at -50 °C and then decreases with a further increase in freezing temperature to -20 °C. Furthermore, the strain sensors offer excellent durability and stability, with their piezoresistivities remaining virtually unchanged even after 10 000 cycles of high-strain loading-unloading. These novel findings pave the way to custom design strain sensors with a desirable piezoresistive behavior.

RESUMEN

The continued miniaturization of electronic components demands integrated liquid cooling systems with minimized external connections and fabrication costs that can be implanted very close to localized hot spots. This might be challenging for existing liquid cooling systems because most of them rely on external pumps, connecting tubes, and microfabricated heat sinks. Here, we demonstrate an integrated liquid cooling system by utilizing a small droplet of liquid metal Galinstan, which is placed over the hot spot. Energizing the liquid metal droplet with a square wave signal creates a surface tension gradient across the droplet, which induces Marangoni flow over the surface of droplet. This produces a high flow rate of coolant medium through the cooling channel, enabling a "soft" pump. At the same time, the high thermal conductivity of liquid metal extends the heat transfer surface and facilitates the dissipation of heat, enabling a "soft" heat sink. This facilitates the rapid cooling of localized hot spots, as demonstrated in our experiments. Our technology facilitates customized liquid cooling systems with simple fabrication and assembling processes, with no moving parts that can achieve high flow rates with low power consumption.

RESUMEN

Due to the growing implications of energy costs and carbon footprints, the need to adopt inexpensive, green energy harvesting strategies are of paramount importance for the long-term conservation of the environment and the global economy. To address this, the feasibility of harvesting low power density ambient RF energy simultaneously from multiple sources is examined. A high efficiency multi-resonant rectifier is proposed, which operates at two frequency bands (478-496 and 852-869 MHz) and exhibits favorable impedance matching over a broad input power range (-40 to -10 dBm). Simulation and experimental results of input reflection coefficient and rectified output power are in excellent agreement, demonstrating the usefulness of this innovative low-power rectification technique. Measurement results indicate an effective efficiency of 54.3%, and an output DC voltage of 772.8 mV is achieved for a multi-tone input power of -10 dBm. Furthermore, the measured output DC power from harvesting RF energy from multiple services concurrently exhibits a 3.14 and 7.24 fold increase over single frequency rectification at 490 and 860 MHz respectively. Therefore, the proposed multi-service highly sensitive rectifier is a promising technique for providing a sustainable energy source for low power applications in urban environments.

RESUMEN

Assembled nanofin heat sinks, nanostructures which are formed via external forces in a cooling microfluidic to remove heat from hot spots, are a new concept that has recently been introduced. In this work, we investigate nanofin structures formed by CrO2 and Fe2O3 magnetic nanoparticles and compare their performance. Thermal imaging is used for comparison of three cases including: (i) DI water as the coolant liquid, (ii) suspension of magnetic particles in DI water, and (iii) suspension of magnetic particles in DI water in the presence of a magnetic field. For each case, the experiments are conducted at three different flow rates of 10, 40 and 120 µl min(-1). Our results suggest that the high thermal conductivity of the nanofins composed of CrO2 significantly enhances the heat exchange across the microchannel. The proof-of-concept magnetophoretic system can offer a practical solution for the cooling of future compact electronics.

RESUMEN

Recently introduced passive wireless strain sensors based on microstrip patch antennas have shown great potential for reliable health and usage monitoring in aerospace and civil industries. However, the wireless interrogation range of these sensors is limited to few centimeters, which restricts their practical application. This paper presents an investigation on the effect of circular microstrip patch antenna (CMPA) design on the quality factor and the maximum practical wireless reading range of the sensor. The results reveal that by using appropriate substrate materials the interrogation distance of the CMPA sensor can be increased four-fold, from the previously reported 5 to 20 cm, thus improving considerably the viability of this type of wireless sensors for strain measurement and damage detection.

RESUMEN

We present the thermal analysis of liquid containing Al(2)O(3) nanoparticles in a microfluidic platform using an infrared camera. The small dimensions of the microchannel along with the low flow rates (less than 120 µl min(-1)) provide very low Reynolds numbers of less than 17.5, reflecting practical parameters for a microfluidic cooling platform. The heat analysis of nanofluids has never been investigated in such a regime, due to the deficiencies of conventional thermal measurement systems. The infrared camera allows non-contact, three dimensional and high resolution capability for temperature profiling. The system was studied at different w/w concentrations of thermally conductive Al(2)O(3) nanoparticles and the experiments were in excellent agreement with the computational fluid dynamics (CFD) simulations.

RESUMEN

Through an integration of wireless communication and sensing technologies, the concept of a body sensor network (BSN) was initially proposed in the early decade with the aim to provide an essential technology for wearable, ambulatory, and pervasive health monitoring for elderly people and chronic patients. It has become a hot research area due to big opportunities as well as great challenges it presents. Though the idea of an implantable BSN was proposed in parallel with the on-body sensor network, the development in this area is relatively slow due to the complexity of human body, safety concerns, and some technological bottlenecks such as the design of ultralow-power implantable RF transceiver. This paper describes a new wireless implantable BSN that operates in medical implant communication service (MICS) frequency band. This system innovatively incorporates both sensing and actuation nodes to form a closed-control loop for physiological monitoring and drug delivery for critically ill patients. The sensing node, which is designed using system-on-chip technologies, takes advantage of the newly available ultralow-power Zarlink MICS transceiver for wireless data transmission. Finally, the specific absorption rate distribution of the proposed system was simulated to determine the in vivo electromagnetic field absorption and the power safety limits.

Asunto(s)

RESUMEN

A novel multichannel vector sum phase shifter that is suitable for phased array antenna applications is demonstrated. Each channel is implemented using a distinct optical wavelength. Selective control of each channel is performed using an acousto-optic polarization coupler. The concept is successfully demonstrated for two individually controlled channels. For each channel, a continuously variable frequency linear phase shift is demonstrated between DC and 7 GHz, with the phasing range exceeding 100 degrees.