RESUMEN

OBJECTIVES: Pulpal inflammation is often associated with odontogenic pain. Dental pulp is abundantly innervated with sensory fibers encompassing neuropeptides. Neurokinin A (NKA) and substance P (SP) are important neuropeptides in the dental pulp that can cause neurogenic inflammation. Since no previous study has assessed dental pulp neuropeptides in children, this study aimed to compare the level of NKA and SP in gingival crevicular fluid (GCF) of sound and symptomatic carious primary teeth. MATERIALS AND METHODS: Samples of GCF were obtained of 20 sound and 20 painful carious primary teeth. Enzyme-linked immunosorbent assay (ELISA) was used to quantify neuropeptides in GCF. Data were analyzed using paired t-test, ANOVA, Kolmogorov-Smirnov test and correlation coefficient test. RESULTS: A significant difference was noted in the level of NKA in GCF of painful and sound teeth (2.23 pg/ml in painful, and 1.84 pg/ml in sound teeth, P<0.05). The difference between the two groups regarding SP was not significant (2.23 pg/ml in painful, and 2.02 pg/ml in sound teeth, P>0.05). CONCLUSIONS: The results showed that the level of NKA and SP was higher in GCF of painful teeth compared to that of sound teeth. This difference was statistically significant with regard to NKA. Thus, these neuropeptides can serve as indicators for pathological activities in teeth with symptomatic irreversible pulpitis.

RESUMEN

PURPOSE: Clinical experience shows that formation of calculus is a very rare phenomenon in primary teeth, but it increases as the permanent teeth erupt. The purpose of this study was to assess the relationship between dental calculus, dental anatomy, and salivary factors in primary and mixed dentition stages. METHODS: A cross-sectional study was carried out to determine the buccolingual dimensions of the most concave and the most convex surfaces of the lingual aspect of mandibular central incisor crowns in a sample group of 120 three- to five-old children and 120 eight- to 10-year old children. Saliva samples were collected from 20 in each group. Data were analyzed using t tests. RESULTS: Significant differences were found between the ratio of the buccolingual dimensions of the most convex to the most concave areas of the lingual surfaces in primary and permanent incisors (P=0.028). Saliva analysis revealed significant differences in total protein (P=0.002), sodium (P=0.037), bicarbonate (P=0.003), and ammonia (P=0.025) between the two age groups. CONCLUSIONS: Anatomic and salivary factors may be important reasons for the differences in calculus formation.

Asunto(s)

RESUMEN

OBJECTIVES: It is not clear what type of pre-crimped crown is more successful in achieving greater marginal adaptation following re-crimping. This study aimed to assess the changes in the circumference of 3M ESPE and MIB pre-crimped stainless steel crowns (SSCs) for the primary maxillary and mandibular first and second molars following re-crimping. MATERIALS AND METHODS: This was an in-vitro, experimental study. Initial photographs were obtained from the margins of 3M and MIB SSCs for the upper and lower primary molars using a digital camera. Crown margins were crimped by applying 0.2N force using 114 and 137 pliers. Post-crimping photographs were also obtained and the changes in crown circumference after crimping were calculated using AutoCad software. The percentage of reduction in the circumference of crowns for each tooth was statistically analyzed based on the type of crown using student t-test. The effect of crown design and the associated teeth on the decreased circumference percentage was statistically analyzed by two-sided ANOVA. RESULTS: The percentage of reduction in lower E SSC circumference was 3.71±0.39% in MIB and 6.29±0.62% in 3M crowns. These values were 3.55±0.55% and 7.15±1.13% for the lower Ds, and 3.95±0.43 and 6.24±0.85% for the upper Ds, respectively. For the upper Es, these values were found to be 3.12±0.65% and 5.14±0.94%, respectively. For each tooth, a significant difference was found between MIB and 3M SSCs in terms of the percentage of reduction in crown circumference following crimping. The magnitude of this reduction was smaller in MIB compared to 3M SSCs (P<0.001). CONCLUSION: Considering the significant reduction in the marginal circumference of precrimped SSCs following re-crimping, it appears that this manipulation must be necessarily performed for MIB and 3M pre-crimped SSCs. By using 3M SSCs, higher marginal adaptation can be achieved following crimping.

RESUMEN

INTRODUCTION: The aim of this study was to evaluate and compare the in vitro effect of the Erbium-Doped Yttrium Aluminum Garnet (Er:YAG) laser with different radiation distances and high-speed rotary treatment on the shear bond strength of flowable composite to enamel of human permanent posterior teeth. METHODS: freshly extracted human molar teeth with no caries or other surface defects were used in this study (n=45). The teeth were randomly divided into 3 groups. Group 1: treated with non-contact Er:YAG Laser and etched with Er:YAG laser, Group 2: treated with contact Er:YAG Laser and etched with Er:YAG laser, Group 3 (control): treated with diamond fissure bur and etched with acid phosphoric 37%. Then the adhesive was applied on the surafces of the teeth and polymerized using a curing light appliance. Resin cylinders were fabricated from flowable composite. Shear bond strength was tested at a crosshead speed of 0.5 mm/min. RESULTS: The amount of Shear Bond Strength (SBS) in the 3 treatment groups was not the same (P<0.05).The group in which enamel surfaces were treated with diamond fissure bur and etched with acid (conrtol group) had the highest mean shear bond strength (19.92±4.76) and the group in which the enamel surfaces were treated with contact Er:YAG laser and etched with Er:YAG laser had the lowest mean shear bond strength (10.89±2.89). Mann-whitney test with adjusted P-value detected significant difference in shear bond strength between the control group and the other 2 groups (P < 0.05). CONCLUSION: It was concluded that both contact and non-contact Er:YAG laser treatment reduced shear bond strength of flowable resin composite to enamel in comparison with conventional treatment with high speed rotary. Different Er:YAG laser distance irradiations did not influence the shear bond strength of flowable composite to enamel.