RESUMEN

Direct electron detectors have played a key role in the recent increase in the power of single-particle electron cryomicroscopy (cryoEM). In this chapter, we summarize the background to these recent developments, give a practical guide to their optimal use, and discuss future directions.

Asunto(s)

RESUMEN

Low dose electron imaging applications such as electron cryo-microscopy are now benefitting from the improved performance and flexibility of recently introduced electron imaging detectors in which electrons are directly incident on backthinned CMOS sensors. There are currently three commercially available detectors of this type: the Direct Electron DE-20, the FEI Falcon II and the Gatan K2 Summit. These have different characteristics and so it is important to compare their imaging properties carefully with a view to optimise how each is used. Results at 300keV for both the modulation transfer function (MTF) and the detective quantum efficiency (DQE) are presented. Of these, the DQE is the most important in the study of radiation sensitive samples where detector performance is crucial. We find that all three detectors have a better DQE than film. The K2 Summit has the best DQE at low spatial frequencies but with increasing spatial frequency its DQE falls below that of the Falcon II.

RESUMEN

BACKGROUND: Hassall's corpuscles (HC) are commonly used as diagnostic features for identifying human thymus and are still present in thymuses undergoing fatty degeneration in young adults. However, few studies have been performed on human fetuses. AIM: A cross-sectional study was done, to study the morphology of HC in human fetuses. MATERIALS AND METHODS: Twenty-eight thymuses were collected from fetuses of gestational age ranging from 11 to 40 weeks. Thymuses were processed by paraffin embedding methods and hematoxylin and eosin staining. RESULTS: The size of HC varied from very small (100 microns) to very large corpuscles (> 900 microns). A high level of polymorphism was also observed, from round to unusual or odd shapes corpuscles. The degenerated reticulo-epithelial cells represented the starting point in HC formation. The growth of HC was rapid, especially near 28 weeks, and the level of HC polymorphism was significantly greater after 28 weeks of gestation. In advanced stages of gestation, the increase in size of some corpuscles reduced the spaces between them, and some patterns strongly supported the hypothesis that some HC had fused in a single and larger corpuscle. CONCLUSION: The rapid rise in number and size of HC around 28 weeks of gestation would fit with their role in the negative selection process of thymocytes.

RESUMEN

Electron microscopy (EM) is an important tool for high-resolution structure determination in applications ranging from condensed matter to biology. Electronic detectors are now used in most applications in EM as they offer convenience and immediate feedback that is not possible with film or image plates. The earliest forms of electronic detector used routinely in transmission electron microscopy (TEM) were charge coupled devices (CCDs) and for many applications these remain perfectly adequate. There are however applications, such as the study of radiation-sensitive biological samples, where film is still used and improved detectors would be of great value. The emphasis in this review is therefore on detectors for use in such applications. Two of the most promising candidates for improved detection are: monolithic active pixel sensors (MAPS) and hybrid pixel detectors (of which Medipix2 was chosen for this study). From the studies described in this review, a back-thinned MAPS detector appears well suited to replace film in for the study of radiation-sensitive samples at 300 keV, while Medipix2 is suited to use at lower energies and especially in situations with very low count rates. The performance of a detector depends on the energy of electrons to be recorded, which in turn is dependent on the application it is being used for; results are described for a wide range of electron energies ranging from 40 to 300 keV. The basic properties of detectors are discussed in terms of their modulation transfer function (MTF) and detective quantum efficiency (DQE) as a function of spatial frequency.

Asunto(s)

RESUMEN

Quantitative analysis of electron microscope images of organic and biological two-dimensional crystals has previously shown that the absolute contrast reached only a fraction of that expected theoretically from the electron diffraction amplitudes. The accepted explanation for this is that irradiation of the specimen causes beam-induced charging or movement, which in turn causes blurring of the image due to image or specimen movement. In this paper, we used three different approaches to try to overcome this image-blurring problem in monolayer crystals of paraffin. Our first approach was to use an extreme form of spotscan imaging, in which a single image was assembled on film by the successive illumination of up to 50,000 spots, each of a diameter of around 7 nm. The second approach was to use the Medipix II detector with its zero-noise readout to assemble a time-sliced series of images of the same area in which each frame from a movie with up to 400 frames had an exposure of only 500 electrons. In the third approach, we simply used a much thicker carbon support film to increase the physical strength and conductivity of the support. Surprisingly, the first two methods involving dose fractionation in space or time produced only partial improvements in contrast whereas the third approach produced many virtually perfect images, where the absolute contrast predicted from the electron diffraction amplitudes was observed in the images. We conclude that it is possible to obtain consistently almost perfect images of beam-sensitive specimens if they are attached to an appropriately strong and conductive support; however great care is needed in practice and the problem remains of how to best image ice-embedded biological structures in the absence of a strong, conductive support film.

Asunto(s)

RESUMEN

We compare the direct electron imaging performance at 120keV of a monolithic active pixel sensor (MAPS) operated in a conventional integrating mode with the performance obtained when operated in a single event counting mode. For the combination of sensor and incident electron energy used here, we propose a heuristic approach with which to process the single event images in which each event is renormalised to have an integrated weight of unity. Using this approach we find enhancements in the Nyquist frequency modulation transfer function (MTF) and detective quantum efficiency (DQE) over the corresponding integrating mode values by factors of 8 and 3, respectively.

Asunto(s)

RESUMEN

Recent progress in detector design has created the need for a careful side-by-side comparison of the modulation transfer function (MTF) and resolution-dependent detective quantum efficiency (DQE) of existing electron detectors with those of detectors based on new technology. We present MTF and DQE measurements for four types of detector: Kodak SO-163 film, TVIPS 224 charge coupled device (CCD) detector, the Medipix2 hybrid pixel detector, and an experimental direct electron monolithic active pixel sensor (MAPS) detector. Film and CCD performance was measured at 120 and 300 keV, while results are presented for the Medipix2 at 120 keV and for the MAPS detector at 300 keV. In the case of film, the effects of electron backscattering from both the holder and the plastic support have been investigated. We also show that part of the response of the emulsion in film comes from light generated in the plastic support. Computer simulations of film and the MAPS detector have been carried out and show good agreement with experiment. The agreement enables us to conclude that the DQE of a backthinned direct electron MAPS detector is likely to be equal to, or better than, that of film at 300 keV.

RESUMEN

The advantages of backthinning monolithic active pixel sensors (MAPS) based on complementary metal oxide semiconductor (CMOS) direct electron detectors for electron microscopy have been discussed previously; they include better spatial resolution (modulation transfer function or MTF) and efficiency at all spatial frequencies (detective quantum efficiency or DQE). It was suggested that a 'thin' CMOS detector would have the most outstanding properties [1-3] because of a reduction in the proportion of backscattered electrons. In this paper we show, theoretically (using Monte Carlo simulations of electron trajectories) and experimentally that this is indeed the case. The modulation transfer functions of prototype backthinned CMOS direct electron detectors have been measured at 300keV. At zero spatial frequency, in non-backthinned 700-mum-thick detectors, the backscattered component makes up over 40% of the total signal but, by backthinning to 100, 50 or 35mum, this can be reduced to 25%, 15% and 10%, respectively. For the 35mum backthinned detector, this reduction in backscatter increases the MTF by 40% for spatial frequencies between 0.1 and 1.0 Nyquist. As discussed in the main text, reducing backscattering in backthinned detectors should also improve DQE.

RESUMEN

Two types of direct electron detectors, potentially useful in low energy electron microscopy and photoemission electron microscopy (LEEM/PEEM) experiments, are reviewed in this paper. Hybrid pixel detectors, using a silicon sensor and based on Medipix2 offer a high detective quantum efficiency, due to an essentially noiseless readout, but are technically challenging. Backthinned monolithic active pixel sensors (MAPS) are not noise-free but have other advantages as discussed in this review.

RESUMEN

OBJECTIVE: To determine the accuracy of naked eye assessment of surgical margins after formalin fixation in vulval cancer in comparison with microscopic assessment. DESIGN: Retrospective review. SETTING: The Gynaecological Cancer Centre, St Bartholomew's Hospital, London, U.K. POPULATION: Patients with primary vulval cancer who underwent surgery from 1997 to 2006. METHODS: Histopathology reports were reviewed and data on surgical margins were analysed. After formalin fixation, pathologists analysed surgical margins and measured them with a ruler. This measurement was compared with microscopic measurement. Other clinicopathologic variables were also recorded and compared. MAIN OUTCOME MEASURE: Comparison between macroscopic and microscopic measurement, and the relation to clinicopathological variables. RESULTS: Naked eye assessment of surgical margins was within 2 mm of correlated microscopic measurement in 29 patients (Group 1). In ten patients the macroscopic measurement of clear margins was less than the microscopic (Group 2). In the remaining 11 cases (22%) naked eye observation overestimated the normal skin margins (Group 3). Seven patients from this group eventually fell into the unfavourable prognostic category of surgical margins <8 mm. The presence of LVSI was significantly more frequent in Group 3 than in the other two groups (p = 0.01). The difference between other variables of the study groups was statistically non-significant. CONCLUSION: Our study demonstrates that naked eye assessment of surgical margins after formalin fixation is inaccurate and that surgical margins are often inadequate. We conclude that tumours with LVSI should be considered for a wider surgical excision.

Asunto(s)

Asunto(s)

RESUMEN

Due to the increasing popularity of electron cryo-microscopy (cryoEM) in the structural analysis of large biological molecules and macro-molecular complexes and the need for simple, rapid and efficient readout, there is a persuasive need for improved detectors. Commercial detectors, based on phosphor/fibre optics-coupled CCDs, provide adequate performance for many applications, including electron diffraction. However, due to intrinsic light scattering within the phosphor, spatial resolution is limited. Careful measurements suggest that CCDs have superior performance at lower resolution while all agree that film is still superior at higher resolution. Consequently, new detectors are needed based on more direct detection, thus avoiding the intermediate light conversion step required for CCDs. Two types of direct detectors are discussed in this review. First, there are detectors based on hybrid technology employing a separate pixellated sensor and readout electronics connected with bump bonds-hybrid pixel detectors (HPDs). Second, there are detectors, which are monolithic in that sensor and readout are all in one plane (monolithic active pixel sensor, MAPS). Our discussion is centred on the main parameters of interest to cryoEM users, viz. detective quantum efficiency (DQE), resolution or modulation transfer function (MTF), robustness against radiation damage, speed of readout, signal-to-noise ratio (SNR) and the number of independent pixels available for a given detector.

Asunto(s)

Asunto(s)

Asunto(s)

RESUMEN

A series of simple tests have been used to measure the performance of flat-bed film scanners suitable for digitisation of electron micrographs. Two of the film scanners evaluated are commercially available and one has been constructed in the laboratory paying special attention to the needs of the electron microscopist. The tests may be useful for others.

Asunto(s)

RESUMEN

The electron imaging performance of Medipix2 is described. Medipix2 is a hybrid pixel detector composed of two layers. It has a sensor layer and a layer of readout electronics, in which each 55 microm x 55 microm pixel has upper and lower energy discrimination and MHz rate counting. The sensor layer consists of a 300 microm slab of pixellated monolithic silicon and this is bonded to the readout chip. Experimental measurement of the detective quantum efficiency, DQE(0) at 120 keV shows that it can reach approximately 85% independent of electron exposure, since the detector has zero noise, and the DQE(Nyquist) can reach approximately 35% of that expected for a perfect detector (4/pi(2)). Experimental measurement of the modulation transfer function (MTF) at Nyquist resolution for 120 keV electrons using a 60 keV lower energy threshold, yields a value that is 50% of that expected for a perfect detector (2/pi). Finally, Monte Carlo simulations of electron tracks and energy deposited in adjacent pixels have been performed and used to calculate expected values for the MTF and DQE as a function of the threshold energy. The good agreement between theory and experiment allows suggestions for further improvements to be made with confidence. The present detector is already very useful for experiments that require a high DQE at very low doses.

Asunto(s)

RESUMEN

The conversion of the genomic information produced by the recent sequencing projects into a comprehensive understanding of the human proteome has yet to occur. A new technology that represents a potential bridge between genomics and proteomics is reverse transfection. Reverse transfection cell microarrays are produced by overlaying cDNA arrays with mammalian cells, generating localized clusters of transfected cells with each cluster overexpressing a unique protein. This miniaturized cell-based microarray format affords parallel functional analysis of thousands of cDNA constructs in a high throughput format. In this report we document the development of a co-transfection methodology for reverse transfection applications. The demonstrated high co-transfection efficiency with a "marker" plasmid encoding for GFP enables the identification of transfected cells and eliminates the need for epitope-tagged constructs in cell-based high throughput screening applications using reverse transfection. This co-transfection method was used to study in parallel the structure/function of multiple versions of the v-Src protein using automated fluorescence microscopy. The wild-type v-Src protein and four mutants having insertions or deletions in the SH2 or SH3 domains displayed high levels of tyrosine kinase activity in HEK293T cells. Three other mutated v-Src proteins, including a kinase-dead version, were shown to be defective for tyrosine kinase activity. This reverse co-transfection approach is applicable for high throughput screening of both cDNA libraries and positional scanning recombinant protein libraries.

Asunto(s)

RESUMEN

Comprehensive genome scans involving many thousands of SNP assays will require significant amounts of genomic DNA from each sample. We report two successful methods for amplifying whole-genomic DNA prior to SNP analysis, multiple displacement amplification, and OmniPlex technology. We determined the coverage of amplification by analyzing a SNP linkage marker set that contained 2320 SNP markers spread across the genome at an average distance of 2.5 cM. We observed a concordance of >99.8% in genotyping results from genomic DNA and amplified DNA, strongly indicating the ability of both methods used to amplify genomic DNA in a highly representative manner. Furthermore, we were able to achieve a SNP call rate of >98% in both genomic and amplified DNA. The combination of whole-genome amplification and comprehensive SNP linkage analysis offers new opportunities for genetic analysis in clinical trials, disease association studies, and archiving of DNA samples.

Asunto(s)

RESUMEN

BACKGROUND: Rolling circle amplification of ligated probes is a simple and sensitive means for genotyping directly from genomic DNA. SNPs and mutations are interrogated with open circle probes (OCP) that can be circularized by DNA ligase when the probe matches the genotype. An amplified detection signal is generated by exponential rolling circle amplification (ERCA) of the circularized probe. The low cost and scalability of ligation/ERCA genotyping makes it ideally suited for automated, high throughput methods. RESULTS: A retrospective study using human genomic DNA samples of known genotype was performed for four different clinically relevant mutations: Factor V Leiden, Factor II prothrombin, and two hemochromatosis mutations, C282Y and H63D. Greater than 99% accuracy was obtained genotyping genomic DNA samples from hundreds of different individuals. The combined process of ligation/ERCA was performed in a single tube and produced fluorescent signal directly from genomic DNA in less than an hour. In each assay, the probes for both normal and mutant alleles were combined in a single reaction. Multiple ERCA primers combined with a quenched-peptide nucleic acid (Q-PNA) fluorescent detection system greatly accellerated the appearance of signal. Probes designed with hairpin structures reduced misamplification. Genotyping accuracy was identical from either purified genomic DNA or genomic DNA generated using whole genome amplification (WGA). Fluorescent signal output was measured in real time and as an end point. CONCLUSIONS: Combining the optimal elements for ligation/ERCA genotyping has resulted in a highly accurate single tube assay for genotyping directly from genomic DNA samples. Accuracy exceeded 99 % for four probe sets targeting clinically relevant mutations. No genotypes were called incorrectly using either genomic DNA or whole genome amplified sample.

Asunto(s)

RESUMEN

Preparation of genomic DNA from clinical samples is a bottleneck in genotyping and DNA sequencing analysis and is frequently limited by the amount of specimen available. We use Multiple Displacement Amplification (MDA) to amplify the whole genome 10,000-fold directly from small amounts of whole blood, dried blood, buccal cells, cultured cells, and buffy coats specimens, generating large amounts of DNA for genetic testing. Genomic DNA was evenly amplified with complete coverage and consistent representation of all genes. All 47 loci analyzed from 44 individuals were represented in the amplified DNA at between 0.5- and 3.0-fold of the copy number in the starting genomic DNA template. A high-fidelity DNA polymerase ensures accurate representation of the DNA sequence. The amplified DNA was indistinguishable from the original genomic DNA template in 5 SNP and 10 microsatellite DNA assays on three different clinical sample types for 20 individuals. Amplification of genomic DNA directly from cells is highly reproducible, eliminates the need for DNA template purification, and allows genetic testing from small clinical samples. The low amplification bias of MDA represents a dramatic technical improvement in the ability to amplify a whole genome compared with older, PCR-based methods.

Asunto(s)