RESUMEN
The purpose of this study was to evaluate the effect of load on microleakage of pit and fissure sealants. In the first phase of the study load of maximal force (F = 880 N) on central and peripheral enamel was applied. Three groups of ten specimens were tested for microleakage. Group A no application of load, Group B application of load on the central pit of the tooth, and Group application of load on the peripheral enamel 2.5 mm away from the margin of the tooth, at the level of dentinoenamel junction. The results of that study showed significant increase of microleakage on the peripheral sealed enamel, as well as enamel microcracks. So, in the phase II sixty wisdom teeth were sealed with Ultra seal XT plus and load of different magnitude was applied on the peripheral enamel. The specimens were thermocycled for 500 cycles at 5 degrees C and 55 degrees C with a dwell of 30 seconds at each temperature prior to load application. Six groups of ten specimens were tested for microleakage under load. The force was applied at the peripheral enamel, 2.5 mm away from the margin of the tooth, at the level of dentin-enamel junction in cross-section view. Group A: F = 0 N; Group B: F = 300 N; Group C: F = 400 N; Group D: F = 500 N; Group E: F = 600 N; Group F: F = 700 N. Microleakage was scored as distance of dye penetration with 0 = no microleakage and 3 = microleakage to underlying fissure. A linear regression statistics was used with R-squared of 0.31. The groups with load applied (B, C, D, E, F) showed statistically significant results (p < 0.05) compared with group A (F = 0 N). Both, the magnitude of the force and tooth morphology may influence the degree of microleakage observed after the placement of sealants.
Asunto(s)
Fuerza de la Mordida , Filtración Dental , Selladores de Fosas y Fisuras , Resinas Compuestas , Fracaso de la Restauración Dental , Análisis del Estrés Dental , Humanos , Modelos Lineales , Ensayo de Materiales , Tercer MolarRESUMEN
Enameloplasty has been implicated in the successful application of pit and fissure sealants. The present study aimed to evaluate the effect of enameloplasty technique on microleakage of sealants when occlusal force was applied on the teeth. The study also allowed a direct comparison of the effectiveness of enameloplasty, when two different burs were used. Six groups of ten human extracted wisdom teeth were tested. Group A: no load, conventional (no enameloplasty--control); Group B: no load, enameloplasty 1/2 round bur (Brasseler USA); Group C: no load, enameloplasty diamond fissure bur REF/UP 791 (Ultradent); Group D: load 500 N, conventional, Group E: load 500 N, 1/2 round bur; Group F: load 500 N, diamond fissure bur. Specimens were thermocycled for 500 cycles at 5 degrees C and 55 degrees C with a dwell time of 30 seconds after load application. Microleakage was scored as distance of dye penetration with 0 = no microleakage and 3 = microleakage to underling fissure. The Kruskal-Wallis One Way Anova and Mann-Whitney U test showed group D having the greatest degree of microleakage statistically significant (p < 0.05) comparing with other groups. Sealants prepared with the conventional technique (A, D) had statistically significant differences in microleakage with those prepared with enameloplasty (B, C, E, F) (p = 0.01). Enameloplasty in groups with no load (B, C) did reduce microleakage, but not significantly (p = 0.3). However, loaded teeth with enameloplasty appeared to perform superior, as compared to those without (p = 0.005). Regarding the effect of load, teeth without load (Groups A, B, C) were found to have significantly less microleakage than teeth where mechanical force had been applied (Groups D, E, F), (p = 0.01). Microleakage in Group A (conventional technique without load) was significantly less than microleakage in Group D (conventional technique with load), (p = 0.04). However, load did not seem to influence microleakage when enameloplasty had been performed. This finding was true for both round bur enameloplasty (p = 0.29), and fissure bur enameloplasty (p = 0.26). There was no statistically significant difference between Groups B, E (round bur) and C, F (fissure bur) (p > 0.05), or between Groups B and C (p > 0.05) and between Groups E and F (p > 0.05). The results of the study indicated that enameloplasty reduced microleakage of pit and fissure sealants, especially when load was applied to teeth, irrespective of what bur was used to enlarge the fissure, as there was no statistical significant differences between the round and fissured diamond burs. The application of occlusal force to the tooth produces significantly more microleakage, unless enameloplasty is performed.