RESUMEN

The objective of this research was to optimize the natural deep eutectic solvent (NADES) extraction process from sour cherry kernels (Prunus cerasus L.). For polyphenol isolation, conventional solid-liquid extraction was employed using different concentrations of ethanol (0, 10, 20, 30, 40, 50, 60, 70, 80, 90, and 96%), as well as the innovative NADES extraction technique. In the initial phase of the research, a screening of 10 different NADESs was conducted, while extraction was carried out under constant parameters (50 °C, 1:20 w/w, 60 min). NADES 4, composed of lactic acid and glucose in a molar ratio of 5:1, exhibited the highest efficiency in the polyphenol isolation. In the subsequent phase of the research, response surface methodology (RSM) was utilized to optimize the extraction process. Three independent variables, namely temperature, extraction time, and solid-liquid (S/L) ratio, were examined at three different levels. The extracted samples were analyzed for total phenol (TP) and antioxidant activity using the DPPH, ABTS, and FRAP assays. ANOVA and descriptive statistics (R2 and CV) were performed to fit the applied model. According to RSM, the optimal extraction conditions were determined as follows: temperature of 70 °C, extraction time of 161 min, and S/L ratio of 1:25 w/w.

Asunto(s)

RESUMEN

This study aims to compare the suitability of three extraction techniques (cold pressing, Soxhlet and supercritical fluid extraction (SFE)) to isolate oil from cherry seeds. Oils were examined in terms of extraction yield, fatty acids profile, tocopherols yield and antioxidant activity. Additionally, influence of SFE parameters was evaluated using one-factor-at-a-time design with pressure (200−350 bar), temperature (40−70 °C), flow rate (0.2−0.4 kg/h) and particle size (<800 µm and >800 µm). Oil yields ranged from 2.50% to 13.02%, whereas the highest yield was achieved with SFE. Samples were rich in polyunsaturated fatty acids, regardless of the applied extraction technique. The main fatty acids were linoleic (46.32−47.29%), oleic (40.89−41.65%), palmitic (6.56−8.00%) and stearic (2.21−2.30%) acid. Total tocopherols yield was between 16.63 mg/100 g oil and 60.61 mg/100 g oil, and highest yield was achieved with SFE. Among the tocopherols, γ-tocopherol was the most abundant, followed by α-, δ- and ß-tocopherol. Antioxidant activity was determined using 1,1-diphenyl-2-picrylhydrazyl (DPPH) and 2,2'-azinobis-(3-ethylbenzothiazoline-6-sulfonic) cation (ABTS) assays, and the results indicated that SFE extracts exhibited better or comparable antioxidant potential compared to traditional techniques. The comparison between modern and conventional extractions for oil recovery demonstrates pros and cons for the possibility of industrial application.

RESUMEN

This study was primarily focused on the supercritical fluid extraction (SFE) of cherry seed oil and the optimization of the process using sequential extraction kinetics modeling and artificial neural networks (ANN). The SFE study was organized according to Box-Behnken design of experiment, with additional runs. Pressure, temperature and flow rate were chosen as independent variables. Five well known empirical kinetic models and three mass-transfer kinetics models based on the Sovová's solution of SFE equations were successfully applied for kinetics modeling. The developed mass-transfer models exhibited better fit of experimental data, according to the calculated statistical tests (R2, SSE and AARD). The initial slope of the SFE curve was evaluated as an output variable in the ANN optimization. The obtained results suggested that it is advisable to lead SFE process at an increased pressure and CO2 flow rate with lower temperature and particle size values to reach a maximal initial slope.

RESUMEN

The aim of this study was to valorize the oil recovery from red and white grape seeds (Vitis vinifera L.) that remains as by-product after the winemaking process. Oils were extracted by modern techniques, ultrasound assisted (UAE), microwave assisted (MAE) and supercritical fluid extraction (SFE), and compared to the Soxhlet extraction (SE). Firstly, SFE was optimized at different operating conditions: pressure (250-350 bar), temperature (40-60 °C), CO2 flow rate (0.2, 0.3 and 0.4 kg h-1), and particle size (315-800 µm and >800 µm). The highest extraction yields were achieved by SFE at the optimal conditions: 350 bar, 60 °C, 0.4 kg h-1. Afterwards, SFE was compared to SE, UAE and MAE with respect to oil extraction yields, and analyzed for fatty acid composition and antioxidant capacity. Considering the general classification of fatty acids, it was found that samples had high content of polyunsaturated fatty acids, regardless of extraction technology. Tocopherol content was significantly influenced by all extraction methods, whereas UAE and MAE resulted in extracts richer with lipophilic antioxidants. In conclusion, modern extractions that are suited for industrial applications had better performance as compared to SE, as judging by the oil yield and quality.

RESUMEN

The purpose of this study was to estimate the electrochemical behavior and biocompatibility of ultrafine-grained (UFG) commercially pure titanium (CPTi) and Ti-13Nb-13Zr (TNZ) alloy obtained by high-pressure torsion process. Electrochemical behavior of materials in artificial saliva at 37°C was evaluated by potentiodynamic polarization tests and electrochemical impedance spectroscopy (EIS), and the obtained results indicated that UFG TNZ alloy showed corrosion current density (jcorr  = 53 ± 5 nA cm-2 ) which was 2 times lower compared to coarse-grained (CG) TNZ alloy (jcorr  = 110 ± 12 nA cm-2 ) and higher corrosion resistance, while UFG CPTi and CPTi showed approximately the same corrosion rate (mean jcorr ∼ 38-40 nA cm-2 ). Static immersion test in artificial saliva, performed in this study, showed that the released ion concentrations from UFG materials were more than 10 times lower than the permitted concentration (the highest released Ti ion concentration from UFG CPTi and UFG TNZ alloy was 1.12 and 1.28 ppb, respectively, while permitted concentration was 15.5 ppb). The in vitro cytotoxicity tests, as the initial phase of the biocompatibility evaluation, showed that the fraction of surviving cells in all examined materials was much higher compared to the control sample and hence demonstrated absence of cytotoxicity and an increase of fibroblast cells adhesion on UFG materials surfaces. UFG CPTi and UFG TNZ alloy can be considered as promising materials for applications in dentistry due to high corrosion resistance and outstanding biocompatibility which were shown in this study. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1097-1107, 2018.

Asunto(s)