RESUMEN

PURPOSE: Item analysis of multiple-choice questions (MCQs) is an essential tool for identifying items that can be stored, revised, or discarded to build a quality MCQ bank. This study analyzed MCQs based on item analysis to develop a pool of valid and reliable items and investigate stakeholders' perceptions regarding MCQs in a written summative assessment (WSA) based on this item analysis. METHODS: In this descriptive study, 55 questions each from 2016 to 2019 of WSA in preclinical removable prosthodontics for fourth-year undergraduate dentistry students were analyzed for item analysis. Items were categorized according to their difficulty index (DIF I) and discrimination index (DI). Students (2021-2022) were assessed using this question bank. Students' perceptions of and feedback from faculty members concerning this assessment were collected using a questionnaire with a five-point Likert scale. RESULTS: Of 220 items when both indices (DIF I and DI) were combined, 144 (65.5%) were retained in the question bank, 66 (30%) required revision before incorporation into the question bank, and only 10 (4.5%) were discarded. The mean DIF I and DI values were 69% (standard deviation [Std.Dev] = 19) and 0.22 (Std.Dev = 0.16), respectively, for 220 MCQs. The mean scores from the questionnaire for students and feedback from faculty members ranged from 3.50 to 4.04 and from 4 to 5, respectively, indicating that stakeholders tended to agree and strongly agree, respectively, with the proposed statements. CONCLUSION: This study assisted the prosthodontics department in creating a set of prevalidated questions with known difficulty and discrimination capacity.

Asunto(s)

Educación en Odontología , Evaluación Educacional , Prostodoncia , Prostodoncia/educación , Humanos , Educación en Odontología/métodos , Evaluación Educacional/métodos , Estudiantes de Odontología/psicología , Encuestas y Cuestionarios , Participación de los Interesados

RESUMEN

AIM: A variety of anthropometric techniques have been proposed to determine the correct vertical dimension of occlusion. However, none have reported correlating thumb length (TL) with vertical dimension at rest (VDR). This study aimed to correlate the VDR to measurements of the thumb in a multi-national, multi-centric trial in participants with and without orthodontic treatment and establish a regression equation for each region. SETTINGS AND DESIGN: A cross-sectional multi-national, multi-centric correlation trial. MATERIALS AND METHODS: A cross-sectional study was conducted in India and Malaysia with a total of 688 participants. Measurements of thumb and VDR were obtained using a modified Willi's gauge using a standard operating procedure. STATISTICAL ANALYSIS USED: Pearson's correlation coefficient was calculated to determine the correlation between TL and VDR. A multiple linear regression was done to correlate VDR from gender, orthodontic treatment, and length of thumb. RESULTS: Correlation coefficient between TL and VDR in patients with orthodontic treatment was 0.829 and 0.774 in patients without orthodontic treatment. The correlation between TL and VDR in patients with orthodontic treatment in North India was 0.484, P = 0.010 and Malaysia was 0.946, P < 0.001. There were significant correlations between TL and VDR in patients without orthodontic treatment in all regions (P < 0.001). Regression equations were obtained for different ethnic groups for calculating the VDR. CONCLUSION: There was an overall positive correlation between TL and VDR in patients with and without orthodontic treatment. The regression equations presented in this article could help clinicians in their clinical practice and researchers to conduct future trials.

RESUMEN

AIM AND OBJECTIVES: Acrylic teeth are used for fabrication of dentures. Debonding of tooth - denture base bond is routine problem in dental practice. The aim of this study was to comparatively evaluate failure load of acrylic resin denture teeth bonded to three different heat resin. MATERIALS AND METHODS: Four groups were created out of test samples central incisors (11). Group I: Control, whereas Group II, Group III and Group IV were experimental groups modified with diatoric hole, cingulum ledge lock and Teeth modified with both diatoric hole and cingulum ledge lock, respectively. These test specimens with 3 teeth (2 central [11, 21] and 1, lateral [12] incisors) positioned imitating arrangement of teeth in the conventional denture, prepared by three different heat cure materials (DPI, Trevalon, Acralyn-H). A shear load was applied at cingulum of central incisor (11) at 130° to its long axis using universal tester at a cross head speed of 5 mm/min until failure occurred. Failure load test was conducted and statistical analysis was performed using SPSS 16 software package (IBM Company, New York, U.S). RESULTS: Highest failure load was seen in Group IV specimens, prepared by Trevalon but did not significantly differ from that of DPI. CONCLUSION: The failure load of bonding denture teeth to three different heat cure materials was notably affected by modifications of ridge lap before processing. The specimens with a combination of diatoric hole and cingulum ledge lock, prepared by Trevalon showed highest failure load but did not significantly vary from that of DPI. The control group prepared by Acralyn-H showed lowest failure load but did not significantly differ from that of DPI.

RESUMEN

AIM AND OBJECTIVE: Acrylic teeth separates from the denture base and remains a major worry in day-to-day routine dental procedure. The present study was conducted to comparatively evaluate different mechanical modifications of acrylic teeth on bond strength between Lucitone 199 heat cure resin and cross-linked teeth. MATERIALS AND METHODS: The test specimens, central incisors (21) were demarcated into four groups. Group 1 was the control group, whereas Group 2, Group 3, and Group 4 were experimental groups modified with round groove, vertical groove, and T-shaped groove, respectively. The preparation of masterpiece was done by aligning the long axis of the central incisor teeth at 45° to the base of a wax block (8 mm × 10 mm × 30 mm), with ridge lap surface contacting the base. These test specimen (21) was prepared by Lucitone 199 heat cure resin. Evaluation of bond strength of all the specimens was done using universal tester (materials testing machine). Shapiro-Wilk Test, one-way analysis of variance (ANOVA), and Bonferroni test were done to do statistical investigation. RESULTS: Group 1 specimens prepared by Lucitone 199 heat cure resin showed the lowest bond strength and Group 4 specimens prepared with T-shaped groove packed with Lucitone 199 exhibited the highest bond strength. CONCLUSION: The bond strength between Lucitone 199 heat cure resin and cross-linked teeth was increased when mechanical modifications was done on denture teeth. The specimens prepared with T-shaped groove packed with Lucitone 199 heat cure resin showed the highest bond strength followed by Group 3, Group 2, and lastly Group 1 prepared by Lucitone 199 heat cure resin.