RESUMEN
Purpose: Pelvis tilting in sagittal plane influences the acetabular cup position. Majority of total hip arthroplasty (THA) are performed in lateral decubitus surgical position. This study is to assess whether there is any difference in sacral slope between standing and lateral decubitus position and influence of this variation in planning acetabular cup anteversion. Materials and Methods: This is a prospective study including 50 patients operated between January 2020 to March 2022. Preoperative radiograph included lumbosacral spine lateral X-ray in standing, supine and lateral decubitus positions to calculate the sacral slope for assessment of anterior or posterior pelvic tilting. In our study, we determined the position of the acetabular cup based on changes in sacral slope between standing and lateral decubitus postures. For patients whose sacral slope increased from lateral decubitus to standing, we implanted the acetabular component with a higher degree of anteversion. Conversely, for patients with reverse phenomenon, the cup was inserted at lower anteversion. Results: Twenty-four patients (48.0%) had increase in sacral slope from lateral decubitus to standing whereas 26 patients (52.0%) had decrease in sacral slope. There was linear correlation between difference in preoperative sacral slope and postoperative cross table lateral cup anteversion. Harris hip scores improved from 40.78 to 85.43. There was no subluxation or dislocation in any patient at minimum 2-year follow-up. Conclusion: Individualized acetabular cup placement is important for better functional outcome in THA. Evaluation of pelvic tilting in lateral decubitus position is necessary for better positioning of acetabular cup and avoid postoperative complications.
RESUMEN
Background: The use of robotic-assisted total knee arthroplasty (RA-TKA) is gaining traction. There is evidence to suggest that RA-TKA can help to optimize the precision and accuracy of implant positioning and that there may be protective effects on surrounding bony and soft tissues. Yet, there are important differences between the various RA-TKA systems currently on the market. One such newly introduced RA-TKA system uses imageless technology and performs bony cuts with the use of a burr-based device. The learning curve and complications unique to this system have yet to be assessed. Methods: We evaluated 500 consecutive RA-TKA cases using a newly developed burr-based and imageless system which were done by a single surgeon between the months of October 2021 and February 2023. Operative times were recorded and compared to the previous 150 conventional TKA cases allowing for the learning curve to be calculated using the CUSUM method. Intraoperative and postoperative complications were categorically profiled. Results: The learning curve of this RA-TKA system was found to be 6 cases. Intraoperative complications included unintended bony over resection (n = 3), soft tissue injury (n = 2), and robotic system hardware (n = 2) or software (n = 2) malfunction. Postoperative complications consisted of superficial pin site infection (n = 1) and periprosthetic fracture near the pin sites (n = 1). There were no identified cases of prosthetic joint infection, instability events, or wound complications. Conclusions: The learning curve and the complication profile of a newly introduced imageless and burr-based RA-TKA system were described. This information serves to guide surgeons in adopting this technology and can counsel them regarding the potential pitfalls and challenges associated with its integration into practice. The work sheds light on the complexity and learning curve of the recently released imageless burr-based RA-TKA system. This important information is intended to help surgeons accept this cutting-edge technology by providing advice on any errors and difficulties that can occur when integrating it into clinical practice. This information can help surgeons navigate the complexities of integrating this new burr-based robotic technology into knee replacement procedures, enabling them to make well-informed decisions and receive guidance.
RESUMEN
Introduction: Revision total hip arthroplasty requires meticulous planning and execution to achieve the desired outcome. Pelvic vessel injury following total hip arthroplasty is rare, but a well-known and serious complication, having a very high morbidity (15%) and mortality (7%). This case demonstrates the rare occurrence of acetabular screw abutment to the external iliac vessels, which if removed during revision hip surgery without releasing the adhesions around it, will lead to avulsion injury of the vessels and a catastrophic event. Case Report: We present this challenging and unique case of a 64-year-old female patient where the acetabular component screw was found to be adherent to the external iliac vessels, with vascular injury imminent. During revision surgery, the iliac vessels were first released free of all adhesions with the intrapelvis screw using an ilioinguinal incision and retroperitoneal approach. The prosthesis was removed using a posterior approach to the hip joint. Definitive surgery was performed after 2 weeks. Conclusion: Surgeons should be cognizant of the possibility of an avulsion vascular injury in revision cases having intrapelvic screws or implants. The proximity of such an implant with the intrapelvic vasculature must be confirmed preoperatively. Management should be individualized. Dual approach and staged procedure help in a favorable outcome. Vascular injury, revision total hip arthroplasty, screw abutting iliac vessel, external iliac vessel, computed tomographic angiography.