RESUMEN
Multiresistant pathogens such as methicillin-resistant Staphylococcus aureus (MRSA) cause serious postoperative infections. A skin tolerant far-UVC (< 240 nm) irradiation system for their inactivation is presented here. It uses UVC LEDs in combination with a spectral filter and provides a peak wavelength of 233 nm, with a full width at half maximum of 12 nm, and an irradiance of 44 µW/cm2. MRSA bacteria in different concentrations on blood agar plates were inactivated with irradiation doses in the range of 15-40 mJ/cm2. Porcine skin irradiated with a dose of 40 mJ/cm2 at 233 nm showed only 3.7% CPD and 2.3% 6-4PP DNA damage. Corresponding irradiation at 254 nm caused 15-30 times higher damage. Thus, the skin damage caused by the disinfectant doses is so small that it can be expected to be compensated by the skin's natural repair mechanisms. LED-based far-UVC lamps could therefore soon be used in everyday clinical practice to eradicate multiresistant pathogens directly on humans.
Asunto(s)
Desinfección/métodos , Resistencia a Múltiples Medicamentos/efectos de la radiación , Fenómenos Fisiológicos de la Piel/efectos de la radiación , Rayos Ultravioleta , Animales , Infección Hospitalaria/prevención & control , Daño del ADN , Staphylococcus aureus Resistente a Meticilina/crecimiento & desarrollo , Staphylococcus aureus Resistente a Meticilina/efectos de la radiación , Viabilidad Microbiana/efectos de la radiación , Complicaciones Posoperatorias/prevención & control , Tolerancia a Radiación/fisiología , Piel/metabolismo , Piel/patología , Piel/efectos de la radiación , Porcinos , Rayos Ultravioleta/efectos adversosRESUMEN
The effects of composition and p-doping profile of the AlGaN:Mg electron blocking layer (EBL) in 310 nm ultraviolet B (UV-B) light emitting diodes (LEDs) have been investigated. The carrier injection and internal quantum efficiency of the LEDs were simulated and compared to electroluminescence measurements. The light output power depends strongly on the temporal biscyclopentadienylmagnesium (Cp 2 Mg) carrier gas flow profile during growth as well as on the aluminum profile of the AlGaN:Mg EBL. The highest emission power has been found for an EBL with the highest Cp 2 Mg carrier gas flow and a gradually decreasing aluminum content in direction to the p-side of the LED. This effect is attributed to an improved carrier injection and confinement that prevents electron leakage into the p-doped region of the LED with a simultaneously enhanced carrier injection into the active region.
RESUMEN
We propose and demonstrate evanescently-decoupled, solid-angle-optimized distributed Bragg reflectors (DBRs) for AlGaInP light-emitting diodes (LEDs). The thickness of each DBR layer is tuned to the wavelength slightly longer than the emission peak of the active medium in order to maximize the radiated power integrated over the top surface. In addition, to increase the horizontal radiation through the side facets, the glancing-angle reflectivity at the AlInP/AlAs interface is improved by employing an AlAs layer thicker than the attenuation length of the evanescent field. With the improved DBR, the integrated output power of AlGaInP LEDs is enhanced by a factor of 1.9 in comparison to those of LEDs with conventional DBRs. Additional 1.25-fold enhancement is observed by incorporating an square-lattice hole array (a=1200nm) into the top GaP surface by a conventional photolithography.
Asunto(s)
Luz , Microscopía Electrónica de Rastreo , Microscopía Electrónica de Transmisión , FotonesRESUMEN
The nano-imprint lithography method was employed to incorporate wide-area (375 x 330 mum(2)) photonic-crystal (PC) patterns onto the top surface of GaN-based LEDs. When the 280-nm-thick p-GaN was partly etched to ~140 nm, the maximal extraction-efficiency was observed without deteriorating electrical properties. After epoxy encapsulation, the light output of the PC LED was enhanced by 25% in comparison to the standard LED without pattern, at a standard current of 20 mA. By three-dimensional finite-difference time-domain method, we found that the extraction efficiency of the LED tends to be saturated as the etch-depth in the GaN epitaxial-layer becomes larger than the wavelength of the guided modes.