RESUMEN
New methods to direct the self-assembly of particles are highly sought after for multiple applications, including photonics, electronics, and drug delivery. Most techniques, however, are limited to chemical patterning on spherical particles, limiting the range of possible structures. We developed a lithographic technique for fabrication of chemically anisotropic rod-like particles in which we can specify both the size and shape of particles and implement multiple diverse materials to control interfacial interactions. Multiphase rod-like particles, including amphiphilic diblock, triblock, and multiblock were fabricated in the same template mold having a tunable hydrophilic/hydrophobic ratio. Self-assembly of diblock or triblock rods at a water/oil interface led to the formation of bilayer or ribbon-like structures.
Asunto(s)
Interacciones Hidrofóbicas e Hidrofílicas , Compuestos Orgánicos/química , Impresión/métodos , Animales , Anisotropía , Aceites/química , Agua/química , HumectabilidadRESUMEN
The facile preparation of amphiphilic network coatings having a hydrophobic dimethacryloxy-functionalized perfluoropolyether (PFPE-DMA; M(w) = 1500 g mol(-1)) crosslinked with hydrophilic monomethacryloxy functionalized poly(ethylene glycol) macromonomers (PEG-MA; M(w) = 300, 475, 1100 g mol(-1)), intended as non-toxic high-performance marine coatings exhibiting antifouling characteristics is demonstrated. The PFPE-DMA was found to be miscible with the PEG-MA. Photo-cured blends of these materials containing 10 wt% of PEG-MA oligomers did not swell significantly in water. PFPE-DMA crosslinked with the highest molecular weight PEG oligomer (ie PEG1100) deterred settlement (attachment) of algal cells and cypris larvae of barnacles compared to a PFPE control coating. Dynamic mechanical analysis of these networks revealed a flexible material. Preferential segregation of the PEG segments at the polymer/air interface resulted in enhanced antifouling performance. The cured amphiphilic PFPE/PEG films showed decreased advancing and receding contact angles with increasing PEG chain length. In particular, the PFPE/PEG1100 network had a much lower advancing contact angle than static contact angle, suggesting that the PEG1100 segments diffuse to the polymer/water interface quickly. The preferential interfacial aggregation of the larger PEG segments enables the coating surface to have a substantially enhanced resistance to settlement of spores of the green seaweed Ulva, cells of the diatom Navicula and cypris larvae of the barnacle Balanus amphitrite as well as low adhesion of sporelings (young plants) of Ulva, adhesion being lower than to a polydimethyl elastomer, Silastic T2.
Asunto(s)
Biopelículas/efectos de los fármacos , Incrustaciones Biológicas/prevención & control , Materiales Biocompatibles Revestidos , Equipos y Suministros/microbiología , Éteres , Fluorocarburos , Polietilenglicoles , Navíos/instrumentación , Animales , Biopelículas/crecimiento & desarrollo , Materiales Biocompatibles Revestidos/química , Materiales Biocompatibles Revestidos/farmacología , Diatomeas/efectos de los fármacos , Diatomeas/fisiología , Éteres/química , Éteres/farmacología , Fluorocarburos/química , Fluorocarburos/farmacología , Interacciones Hidrofóbicas e Hidrofílicas , Fenómenos Microbiológicos/efectos de los fármacos , Docilidad , Polietilenglicoles/química , Polietilenglicoles/farmacología , Tensoactivos/química , Tensoactivos/farmacología , Thoracica/efectos de los fármacos , Thoracica/fisiología , Ulva/efectos de los fármacos , Ulva/fisiologíaRESUMEN
We investigated the effects of particle shape on shear thickening in densely packed suspensions. Rods of different aspect ratios and nonconvex hooked rods were fabricated. Viscosity curves and normal stresses were measured using a rheometer for a wide range of packing fractions for each shape. Suspensions of each shape exhibit qualitatively similar discontinuous shear thickening. The logarithmic slope of the stress vs shear rate increases dramatically with packing fraction and diverges at a critical packing fraction φ(c) which depends on particle shape. The packing fraction dependence of the viscosity curves for different convex shapes can be collapsed when the packing fraction is normalized by φ(c). Intriguingly, viscosity curves for nonconvex particles do not collapse on the same set as convex particles, showing strong shear thickening over a wider range of packing fraction. The value of φ(c) is found to coincide with the onset of a yield stress at the jamming transition, suggesting the jamming transition also controls shear thickening. The yield stress is found to correspond with trapped air in the suspensions, and the scale of the stress can be attributed to interfacial tension forces which dramatically increase above φ(c) due to the geometric constraints of jamming. Using this connection we show that the jamming transition can be identified by simply looking at the surface of suspensions. The relationship between shear and normal stresses is found to be linear in both the shear thickening and jammed regimes, indicating that the shear stresses come from friction. In the limit of zero shear rate, normal stresses pull the rheometer plates together due to the surface tension of the liquid below φ(c), but push the rheometer plates apart due to jamming above φ(c).
RESUMEN
Herein we report the design of a photocurable amphiphilic co-network consisting of perfluoropolyether and poly(ethylene glycol) segments that display outstanding nonfouling characteristics with respect to spores of green fouling alga Ulva when cured under high humidity conditions. The analysis of contact angle hysteresis revealed that the poly(ethylene glycol) density at the surface was enhanced when cured under high humidity. The nonfouling behavior of nonbiocidal surfaces against marine fouling is rare because such surfaces usually reduce the adhesion of organisms rather than inhibit colonization. We propose that the resultant surface segregation of these materials induced by high humidity may be a promising strategy for achieving nonfouling materials, and such an approach is more important than simply concentrating poly(ethylene glycol) moieties at an interface because the low surface energy has been maintained in our work.
Asunto(s)
Éteres/química , Fluorocarburos/química , Polietilenglicoles/química , Ulva/química , Humedad , Estructura Molecular , Tamaño de la Partícula , Propiedades de SuperficieRESUMEN
Herein we describe a versatile and readily scalable approach for the fabrication of particles with a variety of shapes and sizes from a single master template by augmenting the particle replication in nonwetting templates (PRINT) method with mechanical elongation. Repetition of the elongation steps in one direction leads to the fabrication of linear particles with high aspect ratio (AR), over 40 times greater than in the original master, while a range of particle shapes can be obtained by repeating the elongation procedure while changing the stretching direction, generating diamond, rectangular, curved parallelogram particles from a single cubic master.
Asunto(s)
Éteres/química , Fluorocarburos/química , Silicio/química , Coloides/química , Dimetilpolisiloxanos/química , Tamaño de la Partícula , Polietilenglicoles/química , Propiedades de SuperficieRESUMEN
Suspensions are of wide interest and form the basis for many smart fluids. For most suspensions, the viscosity decreases with increasing shear rate, that is, they shear thin. Few are reported to do the opposite, that is, shear thicken, despite the longstanding expectation that shear thickening is a generic type of suspension behaviour. Here we resolve this apparent contradiction. We demonstrate that shear thickening can be masked by a yield stress and can be recovered when the yield stress is decreased below a threshold. We show the generality of this argument and quantify the threshold in rheology experiments where we control yield stresses arising from a variety of sources, such as attractions from particle surface interactions, induced dipoles from applied electric and magnetic fields, as well as confinement of hard particles at high packing fractions. These findings open up possibilities for the design of smart suspensions that combine shear thickening with electro- or magnetorheological response.
RESUMEN
Amphiphilic networks of perfluoropolyethers (PFPE) and poly(ethylene glycol) (PEG) have been achieved to yield optically transparent, mechanically robust films over a wide range of compositions. Telechelic diols of these oligomers were transformed to a photocurable dimethacryloxy form (DMA) and free radically cured at various composition weight ratios to yield free-standing films. Clear and colorless amphiphilic networks could be achieved when low molar mass versions of both the PFPE-DMA (1 kg/mol) and the PEG-DMA (550 g/mol) were used. The bulk morphologies of the samples were extensively characterized by a variety of techniques including ultraviolet-visible spectroscopy, differential scanning calorimetry, dynamic mechanic thermal analysis, small-angle X-ray scattering, atomic force microscopy, X-ray photoelectron spectroscopy, and optical microscopy, which strongly suggest that nanoscopic to macroscopic phase-separated materials could be achieved. By incorporating a threshold amount of PFPEs into PEG-based hydrogel networks, water swelling could be significantly reduced, which may offer a new strategy for a number of medical device applications. Along these lines, strong inhibition of nonspecific protein adsorption could be achieved with these amphiphilic network materials compared with an oligo(ethylene glycol)-based self-assembled monolayer coated surface.