RESUMEN

Laser-induced graphene (LIG) has garnered much attention due to its facile and chemically free fabrication technique. Metal nanoparticle incorporation into the LIG matrix can improve its electrical and catalytical properties for environmental application. Here, we demonstrate the fabrication of nanoscale zerovalent iron (nZVI) nanoparticle-incorporated LIG (Fe-LIG) and sulfidized-nanoscale zerovalent iron (S-nZVI) nanoparticle-incorporated LIG (SFe-LIG) surfaces. The sheets were first fabricated to investigate nanoparticle loading, successful incorporation in the LIG matrix, and electrochemical performance as electrodes. Fe-LIG and SFe-LIG sheets showed ∼3-3.5 times more charge density as compared with the control LIG sheet. The XPS and its deconvolution confirmed the presence of nZVI and S-nZVI in the Fe-LIG and SFe-LIG surfaces, which can generate in situ hydroxyl radical (•OH) via iron activation of electrogenerated hydrogen peroxide (H2O2) in short in situ electro-Fenton process. After confirmation of the successful incorporation of iron-based nanoparticles in the LIG matrix, filters were fabricated to demonstrate the application in the flow-through filtration. The Fe-LIG and SFe-LIG filters showed ∼10-30% enhanced methylene blue removal under the application of 2.5 V at ∼1000 LMH flux. The Fe-LIG and SFe-LIG filters also showed complete 6-log bacteria and virus removal at 2.5 and 5 V, respectively, while the LIG filters showed only ∼4-log removal. Such enhanced removal by the Fe-LIG and SFe-LIG filters as compared to LIG filters is attributed to the improved charge density, electrochemical activity, and in situ electro-Fenton process. The study shows the potential to develop catalytic LIG-based surfaces for various applications, including contaminant removal and microbial inactivation.

RESUMEN

Water is an essential commodity for society, and alternate resources such as seawater and wastewater are vital for the future. There are various desalination technologies that can provide sufficient and sustainable water sources. Renewable energy-based desalination technologies like solar-based interfacial evaporation are very efficient and sustainable desalination methods. Solar-based interfacial evaporation has been a focus due to its efficient and easy-to-use methods. Still, research is needed for fouling resistance, scalable and low-cost materials, and devices for solar interfacial evaporation. Recent research focuses on the materials for evaporation devices, but various other aspects of device design and fabrication methods are also necessary to improve device performance. In this article, all the evaporator device configurations and strategies for efficient evaporator devices are compiled and summarized. The evaporator devices have been classified into eight main categories: monolayer, bilayer, tree-like design, low-temperature designs, 3D-Origami-based designs, latent heat recovery design, design with storage/batch process, and contactless design. It was found that a good absorber, well-engineered air-water interface, and bottom-layer insulation are necessary for the best systems. The current research focuses on the vapor production output of the devices but not on the water production from devices. So, the focus on device-based water production and the associated cost of the water produced is essential. This article articulates the strategies and various scalable and efficient devices for evaporation-based solar-driven desalination. This article will be helpful for the researchers in improving devices output and coming up with a sustainable desalination and water treatment.

RESUMEN

Chromium [Cr] contamination in groundwater is one of the serious environmental concerns due to the carcinogenicity of its water-soluble and mobile hexavalent [Cr(VI)] form. In spite of the existence of multiple precipitation and adsorption-based Cr(VI) remediation technologies, the usage of sulfidated nano zerovalent iron (S-nZVI) has recently attracted researchers due to its high selectivity. Although S-nZVI effectively immobilized Cr(VI), its long-term performance in multiple shifted equilibrium has not been explored. In this contribution, influences of S-nZVI dosage, initial concentration of Cr(VI), pH, ionic strength, total hardness, sulfate, carbonate, and silicate were probed in ultrapure water. Further experiments were performed in synthetic groundwater to investigate the effects of initial concentration of Cr(VI) in the pH range of 4-8 for 1 g L-1 S-nZVI dosage. Cr(VI) removal rate was quantified in groundwater without pH fixation. Finally, a comparative study between conventional nano zerovalent iron (nZVI) and S-nZVI was conducted in sequential batch reactors to investigate their respective efficiencies during repeated usage. Mechanistic interpretation of the processes governing the immobilization of Cr(VI) was done by integrating the results of these experiments with the metadata. While aggregation due to magnetic properties and rapid oxidation of Fe decreased the efficiency of nZVI with repeated usage, sulfidation minimized the passivation and favored an extended reducing environment because of continuous electron transfer from iron and sulfur components.

Asunto(s)

RESUMEN

Over the last few years, the list of water contaminants has grown tremendously due to many anthropogenic activities. Various conventional technologies are available for water and wastewater treatment. However, micropollutants of emerging concern (MEC) are posing a great threat due to their activity at trace concentration and poor removal efficiency by the conventional treatment processes. Advanced technology like membrane technology can remove MEC to some extent. However, issues like the different chemical properties of MEC, selectivity, and fouling of membranes can affect the removal efficiency. Moreover, the concentrate from the membrane filtration may need further treatment. Enzymatic degradation of pollutants and foulants is one of the green approaches for removing various contaminants from the water as well as mitigating membrane fouling. Biocatalytic membranes (BCMs), in which enzymes are immobilized on membranes, combines the advantages of membrane separation and enzymatic degradation. This review article discussed various commonly used enzymes in BCMs for removing MEC and fouling. The majorly used enzymes were oxidoreductases and hydrolases for removing MEC, antifouling, and self-cleaning ability. The various BCM synthesis processes based on entrapment, crosslinking, and binding have been summarized, along with the effects of the addition of the nanoparticles on the performances of the BCMs. The scale-up, commercial viability, challenges, and future direction for improving BCMs have been discussed and shown bright possibilities for these new generation membranes.

Asunto(s)

RESUMEN

Graphene research has steadily increased, and its commercialization in many applications is becoming a reality because of its superior physicochemical properties and advances in synthesis techniques. However, bulk-scale production of graphene still requires large amounts of solvents, electrochemical treatment, or sonication. Recently, a method was discovered to convert bulk quantities of carbonaceous materials to graphene using flash Joule heating (FJH) and, so named, flash graphene (FG). This method can be used to turn various solid wastes containing the prerequisite element carbon into FG. Globally, more than 2 billion tons of municipal solid waste (MSW) are generated every year and, in many municipalities, are becoming unmanageable. The most commonly used waste management methods include recycling, composting, anaerobic digestion, incineration, gasification, pyrolysis, and landfill disposal. However, around 70% of global waste ends up in landfills or open dumps, while the rest is recycled, composted, or incinerated. Even the various waste valorization techniques, such as pyrolysis and gasification, produce some waste residues that have their ultimate destination in landfills. Thus, technologies that can minimize waste volume or convert waste into valuable products are required. The thermal treatment process of FJH for FG production provides both waste volume reduction and valorization in the form of FG. In this Perspective, we provide an overview of FJH and its possible applications in various types of waste conversion/valorization. We describe the typical current MSW management system as well as the potential for creating FG at various stages and propose a schematic plan for the incorporation of FG in MSW management. We also analyze the strengths, weaknesses, opportunities, and threats of MSW as an FG precursor in terms of technical, economic, environmental, and social sustainability. This valuable waste valorization and management strategy can help achieve near-zero waste and an economy-boosting MSW management system.

Asunto(s)

RESUMEN

Interest in the pathogenesis, detection, and prevention of viral infections has increased broadly in many fields of research over the past year. The development of water treatment technology to combat viral infection by inactivation or disinfection might play a key role in infection prevention in places where drinking water sources are biologically contaminated. Laser-induced graphene (LIG) has antimicrobial and antifouling surface effects mainly because of its electrochemical properties and texture, and LIG-based water filters have been used for the inactivation of bacteria. However, the antiviral activity of LIG-based filters has not yet been explored. Here we show that LIG filters also have antiviral effects by applying electrical potential during filtration of the model prototypic poxvirus Vaccinia lister. This antiviral activity of the LIG filters was compared with its antibacterial activity, which showed that higher voltages were required for the inactivation of viruses compared to that of bacteria. The generation of reactive oxygen species, along with surface electrical effects, played a role in the mechanism of virus inactivation. This new property of LIG highlights its potential for use in water and wastewater treatment for the electrochemical disinfection of various pathogenic microorganisms, including bacteria and viruses.

RESUMEN

The presence of antimicrobials in wastewater (WW), surface water (SW), groundwater (GW), and even in potable water from treatment plants has been reported from many countries. Their presence in the water sources is causing the rise and spread of antimicrobial resistance (AMR), thereby threatening our public health, global economy, and development. This necessitates the constant monitoring of these compounds along with the evaluation of their associated risk to aquatic organisms. In this study, GW, WW, and SW samples from different parts of West Bengal (India) were analyzed using the SPE-HPLC-DAD method for detecting two frequently used fluoroquinolones (ciprofloxacin, CIP and ofloxacin, OFL). The highest concentration of CIP and OFL was 5.75 µg/L (GW) and 17.84 µg/L (WW), respectively. The antimicrobial activity was determined against Escherichia coli and Staphylococcus aureus isolates from WW against CIP, which showed that Escherichia coli and Staphylococcus aureus had developed ~ 69 and ~ 12 times resistance compared to their respective pure strains. The risk assessment showed that CIP poses an insignificant threat to fish and Daphnia (RQ < 1) but a significant threat to green algae and Microcystis aeruginosa (RQ> > 1). OFL concentration also poses a great threat to all the organisms for which the assessment was made (RQ> > 1). Moreover, risk assessment in terms of AMR showed that the present level of these antimicrobials in different water sources could cause the development of resistance among the microbial community (RQ > 1). These results emphasize the need for constant monitoring of pharmaceutical compounds, especially antimicrobials, to be kept under check.

Asunto(s)