RESUMEN

Filter membrane processes are water purification methods that use a partially permeable membrane to separate contaminants from drinking water and wastewater. Although highly effective, they suffer from biofouling due to the aggregation of bacteria and contaminants from the filtrate, thus rendering the membrane unusable. Consequently, the membrane needs to be replaced on a regular basis, which interrupts filtration operation, reduces throughput, and increases production cost. To address this issue, we have developed a new method to remove biofoulants via induction heating on a modified membrane with magnetite (Fe3O4) magnetic nanoparticles (MNPs) coating. Under applied alternating magnetic field (AMF), the surface temperature of the MNPs coating reaches 180 °C with a heating rate of 1.03 °C/s, which disintegrates biofoulants generated by model bacteria (Bacillus subtilis) and by those present in environmental water samples collected from a local lake. The heating process is capable of cleaning biofoulants for several cycles without damaging the filtration function of the membrane. Furthermore, magnetic induction heating on the modified membrane allows uniform high-intensity heat generation on a large surface in only a few minutes using inexpensive MNPs, which can potentially be scaled up for industrial applications.

Asunto(s)

RESUMEN

Response surface methodology was successfully used to optimize the amounts of chitosan (CS), polyethyleneimine (PEI), graphene oxide (GO), and glutaraldehyde (GLA) to produce a multifunctional nanocomposite membrane coating able to remove positively and negatively charged heavy metals, such as Cr(VI) and Cu(II). Batch experiments with different concentrations of the four coating components (GO, CS, PEI, and GLA) on cellulose membranes were carried out with solutions containing 10 ppm Cr(VI) and Cu(II) ions. Reduced quadratic equations for the Cr(VI) and Cu(II) removal were obtained based on the observed results of the batch experiments. The numerical analysis resulted in an optimized solution of soaking for 30 min in CS, 1.95% PEI, 1000 ppm GO, and 1.68% GLA with predicted removal of 90 ± 10 and 30 ± 3% for Cr(VI) and Cu(II), respectively, with a desirability of 0.99. This mathematically optimized solution for the coating was experimentally validated. To determine the best membrane material for the coating, stability of the nanocomposite coating was determined using attenuated total reflectance-infrared spectroscopy in eight membrane materials before and after exposure to four solutions with different water chemistries. The glass microfiber (GMF) membranes were determined to be one of the best materials to receive the coating. Then, the coated GMF filter was further investigated for the removal of Cr(VI) and Cu(II) in single and binary component solutions. The results showed that the coatings were able to remove successfully both heavy metal ions, suggesting its ability to remove positively and negatively charged ions from water.

RESUMEN

In the present study, we take advantage of the high thermal conductivity of graphene nanomaterials to develop a filter that can be easily cleaned via laser irradiation after biofouling occurs. In this investigation, the intensity of the laser beam and the amount of graphene used for membrane coating were investigated with Bacillus subtilis to achieve the most efficient removal of biofoulants. Thermographic measurements of glass microfiber filters coated with 500 µg of graphene showed an increase in temperature of about 328 ± 9 °C in about 6 s when the filters were irradiated with a 21.6 W/cm-2 laser intensity, which allowed successful removal of biofoulants. The thermal cleaning was effective for at least four filtrations without impacting the subsequent microbial removals, which were of ∼5 log for each filtration step followed by laser irradiation. Additionally, the permeability of the coated filters only dropped from 17.8 to 15.9 L/m2s after the laser cleaning procedure. The cleaning procedure was validated by using bayou water with a complex composition of biofoulants. Graphene-coated membranes coupled with laser irradiation afford a very fast and nonhazardous approach to clean biofoulants on graphene-coated membranes.

Asunto(s)