RESUMEN

Pharmaceuticals are present in various waters and can be almost completely rejected by membrane separation processes, i.e., nanofiltration (NF) and reverse osmosis (RO). Nevertheless, the adsorption of pharmaceuticals can decrease their rejection, so adsorption can be considered a very important removal mechanism. In order to increase the lifetime of the membranes, the adsorbed pharmaceuticals must be cleaned from the membrane. The used pharmaceutical (albendazole), the most common anthelmintic for threatening worms, has been shown to adsorb to the membrane (solute-membrane adsorption). In this paper, which is a novelty, commercially available cleaning reagents, NaOH/EDTA solution, and methanol (20%, 50%, and ≥99.6%) were used for pharmaceutical cleaning (desorption) of the NF/RO membranes used. The effectiveness of the cleaning was verified by Fourier-transform infrared spectra of the membranes. Of all the chemical cleaning reagents used, pure methanol was the only cleaning reagent that removed albendazole from the membranes.

RESUMEN

The idea of using drugs from the benzimidazole group as potential antitumor agents is becoming increasingly popular and widespread in research. However, their use as antiparasitics and in cancer treatment will increase their already recorded occurrence in the aquatic environment. In this study, the removal of the anthelmintic mebendazole from aqueous solution was investigated using nanofiltration and reverse osmosis membranes, adsorption on granular activated carbon (GAC), and photolytic degradation. The dense NF90 and reverse osmosis XLE membranes showed almost complete removal (>97.7%), while the NF270 membrane showed a large dependence of removal on initial concentration from 41.9% to 96.6%. Adsorption in the column resulted in complete removal of mebendazole at the highest GAC height used (40 cm) from the solution with the lowest concentration (1 mg/L). Photolytic degradation by artificial light for 2 and 12 h resulted in photodegradation of mebendazole in the range of 23.5−61.4%, forming a new degradation or transformation compound with an m/z ratio of 311. Mebendazole is a photosensitive drug whose photodegradation follows first-order kinetics and depends on the drug concentration. Toxicity was studied with Vibrio fischeri before and after photolysis, and showed a decrease in inhibition after 12 h.

RESUMEN

Ultra-violet light-emitting diode (UV-LED)-based processes for water treatment have shown the potential to surpass the hurdles that prevent the adoption of photocatalysis at a large scale due to UV-LEDs' unique features and design flexibility. In this work, the degradation of five EU Watch List 2020/1161 pharmaceutical compounds was comprehensively investigated. Initially, the UV-A and UV-C photolytic and photocatalytic degradation of individual compounds and their mixtures were explored. A design of experiments (DoE) approach was used to quantify the effects of numerous variables on the compounds' degradation rate constant, total organic carbon abatement, and toxicity. The reaction mechanisms of UV-A photocatalysis were investigated by adding different radical scavengers to the mix. The influence of the initial pH was tested and a second DoE helped evaluate the impact of matrix constituents on degradation rates during UV-A photocatalysis. The results showed that each compound had widely different responses to each treatment/scenario, meaning that the optimized design will depend on matrix composition, target pollutant reactivity, and required effluent standards. Each situation should be analyzed individually with care. The levels of the electrical energy per order are still unfeasible for practical applications, but LEDs of lower wavelengths (UV-C) are now approaching UV-A performance levels.

RESUMEN

In this paper, nanostructured TiO2 film was prepared by the by sol-gel process and dip-coating technique with titanium tetraisopropoxide as a precursor. After heat treatment at 550 °C, the deposited film was characterized by means of micro-Raman spectroscopy and atomic force microscopy (AFM). It was found that the TiO2 film consisted of only the TiO2 anatase phase and showed a granular microstructure. Photocatalytic degradation of azithromycin by using sol-gel nanostructured TiO2 film was studied to define the most effective degradation process for potential use in wastewater treatment. Different factors were evaluated during photocatalysis, such as pH (3, 7, and 10), water matrix (ultrapure water and synthetic municipal waste water effluent), influence of another pharmaceutically active compound (sulfamethoxazole, one of the most often detected pharmaceutic compounds in waste waters), and radiation sources (low pressure ultraviolet (UV) mercury lamps with a UV-A and UV-C range; a light-emitting diode (LED) lamp with a radiation peak at 365 nm). The most effective degradation process was achieved with the UV-C irradiation source in matrices at pH 10. The water matrix had little effect on the photocatalytic degradation rates of azithromycin. The presence of sulfamethoxazole in the water matrix decreased the degradation rate of azithromycin, however, only in matrices with a pH level adjusted to 10. During the experiments, five azithromycin degradation products were identified and none of them showed toxic properties, suggesting effective removal of azithromycin. LED 365 nm as the irradiation source was not as effective as the UV-C lamp. Nevertheless, considering the cost, energy efficiency, and environmental aspects of the irradiation source, the LED lamp could be a "real-life" alternative.

RESUMEN

Febantel is widely used anthelmintic drug active against a range of gastrointestinal parasites in animals. Despite the fact that it has been detected in the aquatic environment, there is no information on its environmental fate. Therefore, abiotic elimination processes of febantel in the aquatic environment have been studied. The results of direct and indirect photodegradation experiments showed that febantel was persistent against solar radiation. Kinetics of hydrolytic elimination was pH and temperature dependent with half-lives in the range from 210 min to 99 days. Febantel metabolites, fenbendazole and fenbendazole sulfone, were found as major degradation products using high-resolution mass spectrometry. The proposed hydrolytic degradation pathway consisted of the base catalyzed hydrolysis followed by consecutive oxidative cyclization to the five-membered ring of the benzo-imidazole derivative. Aquatic toxicity of febantel and its hydrolytic mixture were evaluated toward the luminescence bacteria Vibrio fischeri. Investigation of febantel sorption onto river sediments showed that the best agreement was obtained with the linear model (R2 > 0.99), while the rate of sorption is the best described with the kinetic model of pseudo-second order. The organic carbon-normalized sorption coefficient, KOC, ranged from 1490 to 3894 L kg-1 for five sediment samples. The results of this research demonstrate that febantel persist in the natural waters and potentially could travel far from the source.

Asunto(s)

RESUMEN

For the characterization of grape cultivars, the profile and content of flavonoids are important because these compounds have an impact on grape and wine quality. A new extraction method for the recovery of flavonoids, e.g. anthocyanins, flavonols and flavan-3-ols from grape skins was developed. The optimization of solid-liquid extraction of flavonoids was conducted, with respect to the type of the organic solvent and its percentage in the extraction solvent as well as the extraction temperature and extraction time, using response surface methodology. Optimal conditions were obtained by using extraction solvent composed from acetonitrile:water:formic acid (20:79:1; v/v/v), at an extraction temperature of 50 °C, an extraction time of 1 h in a single-step extraction and with a solid-to-solvent ratio of 1:80 g mL(-1) (125 mg of grape skin powder and 10 mL of extraction solvent). The new optimal extraction method is inexpensive, simple, fast, accurate and selective for the recovery of simple flavonoids.

Asunto(s)

RESUMEN

INTRODUCTION: For the characterisation of grape cultivars, the profile and content of flavonoids are important because these compounds impact grape and wine quality. To determine the correct profile and content of flavonoids, the use of robust, sensitive and reliable methods is necessary. OBJECTIVE: The object of this research is to develop a new ultrasound-assisted extraction (UAE) method for the recovery of flavonoids from grape skins using response surface methodology. METHOD: Optimisation of UAE was performed using a complementary study combining a Box-Behnken experimental design with qualitative analysis by high-performance liquid chromatography. RESULTS: Optimal extraction conditions were obtained using the extraction solvent composed of acetonitrile:water:formic acid (26:73:1, v/v/v) at an extraction temperature of 50 °C, an extraction time of 15 min in a single-extraction step and with a solid-to-solvent ratio of 1:80 g/mL. The calculated relative standard deviations for the optimal extraction method were very low, measuring less than 5%. CONCLUSIONS: This study demonstrates that numerous factors have strong effects on the extraction efficiency, including the type of organic modifier and its percentage in the extraction solvent, the number of extraction steps, the solid-to-solvent ratio, the extraction time and temperature and, finally, the particular nature of analyte and their position within the grape skin cell.

Asunto(s)

RESUMEN

This paper describes the development, optimization, and validation of a method for the determination of five pharmaceuticals from different therapeutic classes (antibiotics, anthelmintics, glucocorticoides) in water samples. Water samples were prepared using SPE and extracts were analyzed by HPLC with diode-array detection. The efficiency of 11 different SPE cartridges to extract the investigated compounds from water was tested in preliminary experiments. Then, the pH of the water sample, elution solvent, and sorbent mass were optimized. Except for optimization of the SPE procedure, selection of the optimal HPLC column with different stationary phases from different manufacturers has been performed. The developed method was validated using spring water samples spiked with appropriate concentrations of pharmaceuticals. Good linearity was obtained in the range of 2.4-200 µg/L, depending on the pharmaceutical with the correlation coefficients >0.9930 in all cases, except for ciprofloxacin (0.9866). Also, the method has revealed that low LODs (0.7-3.9 µg/L), good precision (intra- and interday) with RSD below 17% and recoveries above 98% for all pharmaceuticals. The method has been successfully applied to the analysis of production wastewater samples from the pharmaceutical industry.

Asunto(s)

RESUMEN

BACKGROUND: Emerging contaminants (ECs) are commonly derived from industrial wastewater, which is often a consequence of an inadequate treatment of the latter. Improperly pretreated pharmaceutical wastewater could cause difficulties in operations of wastewater treatment plants while incomplete elimination of ECs during the processing might result in their appearance in drinking water. METHODS: This paper deals with membrane treatment of pharmaceutical wastewater on a laboratory and a pilot scale as well as with the removal of the following veterinary pharmaceuticals (VPs) (sulfamethoxazole, trimethoprim, ciprofloxacin, dexamethasone, and febantel). RESULTS: The pretreatment of pharmaceutical wastewater by means of coagulation and microfiltration (MF) prevented the irreversible fouling of the fine porous structure of the reverse osmosis (RO) and nanofiltration (NF) membranes which were used in the final stage of wastewater processing. The percentage of the removal of the selected VPs ranges from 94% to almost 100% in the case of NF and RO membranes in both scales. The recovery percentage concerning the pilot scale amounted to 88%. Membrane cleaning was successfully carried out in both scales. CONCLUSIONS: The differences in retention between laboratory and pilot tests are due to different raw wastewater quality and different recovery and hydrodynamic of the two systems. Fouling and concentration polarization were more pronounced in laboratory setup (frame-plate module) than in pilot unit (spiral module). The proposed integrated membrane treatment (coagulation, MF, NF, and RO) can be employed for treatment of wastewater originating from pharmaceutical factory. The obtained permeate can be safely discharged to sewer system or could be reused in manufacturing process.

Asunto(s)

RESUMEN

This study explored the removal of five veterinary pharmaceuticals (VPs) (sulfamethoxazole (SMETOX), trimethoprim (TMP), ciprofloxacin (CIPRO), dexamethasone (DEXA) and febantel (FEBA)) from different water matrices (Milli-Q water, model water, tap water and real pharmaceutical wastewater using four types of nanofiltration (NF) membranes (NF90, NF270, NF and HL) and two reverse osmosis (RO) membranes (LFC-1 and XLE). All VPs were added to different water matrices at a concentration of 10 mg/L. Rejections of VPs and water flux were measured. The rejection increased with increase of molecular weight. The highest rejections were obtained with RO membranes (LFC-1, XLE) and tight NF (NF90) membrane. In general, the rejection of VPs was higher in model water and tap water than in Milli-Q water, but the water flux was lower. This was mainly explained by ion adsorption inside the membranes pores. Narrower pore size counteracted the effect of presence of low concentration of natural organic matter (NOM) in tap water. The NOM was assumed to enhance the adsorption of VPs onto membrane surface, increased the size exclusion and electrostatic repulsion also appeared during the transport. Investigated water matrices had influence on water flux decline due to their complexity.

Asunto(s)

RESUMEN

An analytical method for multi-class pharmaceuticals determination in wastewater has been developed and validated. Target compounds were: sulfonamides (sulfadiazine, sulfaguanidine, sulfamethazine, sulfamethoxazole), fluoroquinolones (ciprofloxacin, enrofloxacin, norfloxacin), diaminopyrimidine (trimethoprim), anaesthetic (procaine), anthelmintic (praziquantel and febantel), and macrolide (roxithromycin). The method involves pre-concentration and clean-up by solid-phase extraction (SPE) using Strata-X extraction cartridges at pH 4.0. Target analytes were identified and quantitatively determined by liquid chromatography-tandem mass spectrometry using multiple reaction monitoring (MRM). Recoveries were higher than 50% with relative standard deviation (RSD) below 18.3% for three concentrations. Only for sulfaguanidine was low recovery obtained. Matrix effect was evaluated using matrix-matched standards. The method detection limit (MDL) was between 0.5 and 5 ng L(-1) in spiked water samples. The precision of the method, calculated as relative standard deviation, ranged from 0.5 to 2.0% and from 1.4 to 8.3 for intra-day and inter-day analysis, respectively. The described analytical method was used for determination of pharmaceuticals in effluent wastewaters from the pharmaceutical industry.

Asunto(s)

RESUMEN

This paper focuses on the investigation of different types of SPE sorbents for the preconcentration of eight veterinary pharmaceuticals from water samples. The pharmaceuticals studied were sulfamethazine, sulfadiazine, sulfaguanidine, trimethoprim, oxytetracycline, enrofloxacin, norfloxacin and penicillin G/procaine. Five different SPE materials (Strata-X, Strata-X-C, Strata SDB-L, Strata C8 and Strata C18) from Phenomenex were compared with Oasis HLB with a view to obtaining the best cartridges for all pharmaceuticals investigated. Extraction efficiency was determined by HPLC with diode array detection (DAD). HPLC-DAD separation and quantification of the selected pharmaceuticals were carried out under gradient elution by a binary mixture of 0.01 M oxalic acid and ACN based on cyano modified column (LiChrosphere 100 CN) from Merck. Strata-X provided the best results in the preconcentration of 100 mL water samples, yielding average pharmaceutical recoveries of higher than 90%, except for sulfaguanidine (76.1%). The developed Strata-X-HLPC-DAD method was validated and applied, for the efficient investigation of reverse osmosis/nanofiltration membranes and for the removal of these eight pharmaceuticals from the production wastewater samples. NF90 and XLE membranes were shown to be the best for the rejection of all investigated pharmaceuticals.

Asunto(s)

RESUMEN

This work focuses on the application of SPE-HPLC analysis of important veterinary pharmaceuticals from different classes in highly complex wastewater matrix. The pharmaceutical investigated included three sulfonamides (sulfamethazine, sulfadiazine and sulfaguanidine), a sulfonamide synergist (trimethoprim), a tetracycline (oxytetracycline), a fluoroquinolone (enrofloxacine) and a beta-lactame (penicillin G/procaine). The method involves pre-concentration and clean-up by solid phase extraction (SPE) using Oasis HLB extraction catridges. Final analysis of the selected pharmaceutical compounds was carried out by high-performance liquid chromatography (HPLC) coupled with diode array detector (DAD). Recoveries were ranged from 68.3 to 97.9% with relative standard deviation below 8.4%. Only for sulfaguanidine low recovery was obtained. Limits of quantification were in the range 1.5-100mug/L depending on pharmaceutical. The described method was applied to the determination of pharmaceuticals in wastewater samples from pharmaceutical industry.