RESUMEN
New composites made of natural fiber polymers such as wasted date palm surface fiber (DPSF) and pineapple leaf fibers (PALFs) are developed in an attempt to lower the environmental impact worldwide and, at the same time, produce eco-friendly insulation materials. Composite samples of different compositions are obtained using wood adhesive as a binder. Seven samples are prepared: two for the loose natural polymers of PALF and DPSF, two for the composites bound by single materials of PALF and DPSF using wood adhesive as a binder, and three composites of both materials and the binder with different compositions. Sound absorption coefficients (SACs) are obtained for bound and hybrid composite samples for a wide range of frequencies. Flexural moment tests are determined for these composites. A thermogravimetric analysis test (TGA) and the moisture content are obtained for the natural polymers and composites. The results show that the average range of thermal conductivity coefficient is 0.042-0.06 W/(m K), 0.052-0.075 W/(m K), and 0.054-0.07 W/(m K) for the loose fiber polymers, bound composites, and hybrid composites, respectively. The bound composites of DPSF have a very good sound absorption coefficient (>0.5) for almost all frequencies greater than 300 Hz, followed by the hybrid composite ones for frequencies greater than 1000 Hz (SAC > 0.5). The loose fiber polymers of PALF are thermally stable up to 218 °C. Most bound and hybrid composites have a good flexure modulus (6.47-64.16 MPa) and flexure stress (0.43-1.67 Mpa). The loose fiber polymers and bound and hybrid composites have a low moisture content below 4%. These characteristics of the newly developed sustainable and biodegradable fiber polymers and their composites are considered promising thermal insulation and sound absorption materials in replacing synthetic and petrochemical insulation materials in buildings and other engineering applications.
RESUMEN
Researchers from all around the world have been paying close attention to particle-based power tower technologies. On the King Saud University campus in the Kingdom of Saudi Arabia, the first integrated gas turbine-solar particle heating hybrid system has been realized. In this study, two different types of experiments were carried out to examine how susceptible prospective liner materials for thermal energy storage tanks were to erosion. An accelerated direct-impact test with high particulate temperature was the first experiment. A low-velocity mass-flow test was the second experiment, and it closely mimicked the flow circumstances in a real thermal energy storage tank. The tests were conducted on bare insulating fire bricks (IFBs) and IFBs coated with Tuffcrete 47, Matrigun 25 ACX, and Tuffcrete 60 M. The latter three lining materials were high-temperature-resilient materials made by Allied Mineral Products Inc. (AMP) (Columbus, OH, USA). The results showed that although IFBs coated with AMP materials worked well in this test, the accelerated direct-impact test significantly reduced the bulk of the bare IFB. As a result, lining substances must be added to the surface of IFBs to increase their strength and protection because they cannot be used in situations where particles directly impact their surface. On the other hand, the findings of the 60 h cold-particle mass-flow test revealed that the IFBs were not significantly eroded. Additionally, it was discovered that the degree of erosion on the samples of bare IFB was unaffected by the height of the particle bed.
RESUMEN
Pineapple leaf fiber (PALF), striped sunflower seed fiber (SFSF), and watermelon seed (WMS) are considered natural waste polymer materials, which are biodegradable and sustainable. This study presents new novel thermal insulation and sound absorption materials using such waste as raw materials. PALF, SFSF, and WMS were used as loose, bound, and hybrid samples with different compositions to develop promising thermal insulation and sound-absorbing materials. Eleven sample boards were prepared: three were loose, three were bound, and five were hybrid between PALF with either SFSF or WMS. Wood adhesive was used as a binder for both the bound and hybrid sample boards. Laboratory scale sample boards of size 30 cm × 30 cm with variable thicknesses were prepared. The results show that the average thermal conductivity coefficient for the loose samples at the temperature range 20-80 °C is 0.04694 W/(m.K), 0.05611 W/(m.K), and 0.05976 W/m.K for PALF, SFSF, and WMS, respectively. Those for bound sample boards are 0.06344 W/(m.K), 0.07113 W/(m.K), and 0.08344 W/m.K for PALF, SFSF, and WMS, respectively. The hybrid ones between PALF and SFSF have 0.05921 W/m.K and 0.06845 W/(m.K) for two different compositions. The other hybrid between PALF and WMS has 0.06577 W/(m.K) and 0.07007 for two different compassions. The sound absorption coefficient for most of the bound and hybrid boards is above 0.5 and reaches higher values at some different frequencies. The thermogravimetric analysis for both SFSF and WMS shows that they are thermally stable up to 261 °C and 270 °C, respectively. The three-point bending moment test was also performed to test the mechanical properties of the bound and hybrid sample boards. It should be mentioned that using such waste materials as new sources of thermal insulation and sound absorption materials in buildings and other applications would lead the world to utilize the waste until zero agrowaste is reached, which will lower the environmental impact.
RESUMEN
Utilizing solid particles as a heat-transfer medium in concentrated solar power applications has gained growing attention lately. Unlike molten salts, solid particles offer many benefits, which include: high operating temperatures (greater than 1000 °C), a lack of freezing issues and corrosivity, abundant availability, high thermal energy storage capacity, a low cost, and applicability in direct irradiation. Comprehensive knowledge of thermophysical and optical properties of solid particles is essential to ensure an effective harnessing of solar energy. The most important considerations when selecting solid particles include: thermophysical and optical properties, thermal resistance, crack resistance, satisfactory health and safety risks, availability, and low cost. It is also imperative to consider optical and thermophysical characteristics that might change from what they were "as received" after cyclic heating for a long period. Therefore, the knowledge of thermal performance of particulate materials becomes significant before using them as a heat-transfer medium. In this study, some particulate materials were chosen to study their feasibilities as heat-transfer and storage media for a particle-based central receiver tower system. These particulate materials included white sand, red sand, ilmenite, and Carbobead CP. The candidate particulate materials were heated at high temperatures for 6 h and then cooled to room temperature. After that, cyclic heating was performed on the particulate materials for 500 h at 1200 °C. The optical properties were represented by weighted solar absorptance, and the thermophysical properties of the particulates were measured "as received" and after cyclic heating (aging). EDX and XRD were conducted to quantify the chemical composition and interpret the changes in appearance associated with the particulate materials after cyclic heating. The results showed a considerable agglomeration in all particulates except for white sand in the 6 h heating test, and high agglomeration in the ilmenite. A slight decrease in the optical properties in the white sand and Carbobead CP was found after the aging test. The specific heat was decreased for red and white sand. The EDX and XRD results for white sand and Carbobead CP showed chemical stability, indicating high durability and reliability.